Coaster 102065 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
102065
Server
REVISION 0 : 10/06/2017
REVISION 1 : 03/16/2020 PAGE 1 OF 5COASTERFURNITURE.COM

ITEM: 102065
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
WARNING!
1. Don't attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME 15 MINUTES
PARTS IDENTIFICATION
COASTERFURNITURE.COMPAGE 2 OF 5
HARDWARE IDENTIFICATION
AVSERVER 1PC
BVLEG 5PCS
1
2
3
BOLT
( Ø5/16" x 2" - RBW )
LOCK WASHER
( Ø5/16" - RBW )
FLAT WASHER
( Ø5/16" - RBW )
5PCS
5PCS
5PCS
5ALLEN WRENCH
( 4MM - RBW )
1PC
WOOD DOWEL
( Ø8x30MM - RBW )
10PCS
4
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.

ITEM: 102065
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
COMPLETE
COASTERFURNITURE.COMPAGE 3 OF 5
2
5
1
3
4
BV
AV
BV
BV

OPTIONAL ADJUSTABLE SHELF
COASTERFURNITURE.COM
PAGE 4 OF 5
STEP 2.3
STEP 2.2
STEP 2.1
NOTE:
Phillps head screw driver is required in the assembly process; however, manufacturer does not provide this item.

1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the short screw.
2. Determine where the furniture is to be placed and mark location on the wall for the mounting bracket
screw hole approximately 2" below the bracket mounted to the edge of the furniture.
3. Drill a 3/16" hole in the wall. Press the plastic wall plug into the hole and gently tap until the flange on
the wall plug is against the wall surface.
4. Position the bracket over the wall plug and use the long screw to securely attach the bracket to the wall.
5. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
6. Lace an end of the cable tie down through each bracket. Bring both ends together and slide the
beaded end of the cable tie through the keyhole shaped slot on the other end until snug. Pull down on
the beaded end until it snap locks into the keyhole slot.
7. To double lock return the beaded end back through the keyhole as shown.
8. Check to make sure the cable tie is securely laced and locked to the brackets.
PAGE 5 OF 5COASTERFURNITURE.COM
ANTI-TIPPING INSTALLMENT INSTRUCTIONS
Failure to detach this restraint before moving the furniture may result in injury and damage.
FURNITURE TIPPING RESTRAINT
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
ITEM: 102065

ITEM: 102065
COASTERFURNITURE.COM
Note: Dimension tolerance ±5%
INNER SIZE OF DRAWER : 20.47" X 15.43" X 8.77"H
59" 20"
30.5"
12.32"
12.32"
18.11"
17.32"
18.11"
17.87"
53.5"
20.47"
8.77"
26.57"
2.75"
19"