Coaster 203501KE User manual

203501KE (B1&B2)
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
www.coastercompany.com
R
PAGE 1 OF 4
EASTERN KING SIZE BED
REVISION 0 : 05/16/2014
REVISION 1 : 05/27/2014

ITEM : 203501KE (B1&B2)
HARDWARE IDENTIFICATION
1.Remove hardware from box and sort by size.
2.Please check to see that all hardware and parts are present prior to start of assembly.
3.Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
1.Don't attempt to repair or modify parts that are broken of defective. Please contact the store
2.This product is for home use only and not intended for commercial establishment.
Warning!
immediately.
PAGE 2 OF 4
SMALL ALLEN WRENCH
BIG ALLEN WRENCH
ASSEMBLY TIPS:
ASSEMBLY INSTRUCTIONS
PARTS IDENTIFICATION
B1 (BOX 1)
A
B
1PC
1PC
Z - B1 (BOX 1) - Hardware pack is located in 203501KE (B1)
F BED RAIL 2PCS
203501KE (B1)
*FROM BOX 1
HEADBOARD COMPLETE
Z - B2 (BOX 2) - Hardware pack is located in 203501KE (B2)
5
6PCS
6
8PCS7
8 1PC
1PC
BOLT
C1PC
B2 (BOX 2)
DBED SLAT 4PCS
EBED SLAT SUPPORT
WITH LEVELER 8PCS
G
H
HB
FOOTBOARD LEG
FOOTBOARD PANEL
2PCS
1PC
1PC
8PCS
9
LONG FLAT HEAD SCREW
SHORT FLAT HEAD SCREW
A
B
1PC
1PC
C1PC
HEADBOARD PANEL
RIGHT
HEADBOARD LEG
LEFT
HEADBOARD LEG
6PCS
1BOLT
1PC2 SMALL ALLEN WRENCH
6PCS3 FLAT WASHER
6PCS4 LOCK WASHER
www.coastercompany.com

PAGE 3 OF 4
ASSEMBLY INSTRUCTIONS
203501KE (B1) - BOX 1
203501KE (B1 & B2) - BOX 1 & BOX 2
STEP 3
IF PURCHASE HEADBOARD ONLY, SKIP BELOW STEPS
H
6
G
ITEM : 203501KE (B1&B2)
2
1
4
3
A
C
STICKER LEFT
STICKER RIGHT
A
C
B
B
STEP 2
Align and fasten right (B) & left (C) headboard legs to
headboard panel (A) using bolt(1), lock washer (4) &flat
washer (3) ,then tighten with Allen wrench(2).
STEP 1
Place headboard panel (A) facing downward on soft
surface,and install right (B) & left (C) headboard legs to
headboard panel (A) as per diagram shown.
**Please take note the marking on the leg **
**BACK VIEW
Align and fasten footboard leg (G) to footboard panel (H) using long flat head screw (6) and tighten with screw
driver (Not included).
www.coastercompany.com
PLEASE REMOVE THE
PROTECTIVE FILM
BEFORE ASSEMBLY

PAGE 4 OF 4
ASSEMBLY INSTRUCTIONS
STEP 4
STEP 5 STEP 6
H
F
HB
9D5
ITEM : 203501KE (B1&B2)
E
D
8
7
E
Loosen the bolt.
Align & hook bed rail (F) to headboard (HB) & footboard (H).
Align and fasten bed slat support with
leveler (E) to bed slat (D) using bolt (7) & tighten
with small Allen wrench (8).
6.1) Fully tighten all the bolts at step 4 with big Allen wrench (9).
6.2) Align & fasten bed slat (D) to bed rail (F) using short flat head
screw (5) & tighten with screw driver (NOT INCLUDED).
Then adjust leveler to touch the floor.
www.coastercompany.com
6.1
6.2