Coaster Hartshill 881284 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
COASTERFURNITURE.COM
REVISION 0 : 07/07/2020 PAGE 1 OF 5
881284
File Cabinet

881284
File Cabinet
COASTERFURNITURE.COM
PAGE 2 OF 5
ASSEMBLY TIME 10 MINUTES
PART IDENTIFICATION
FILE CABINET
LEG
1PC
4PCS
6PCS
2PCS
BIG DRAWER DIVIDER
A
B
C
D
E2PCS
ITEM: 881284
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
WARNING!
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediatelly.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
2. This product is for home use only and not intended for commercial establishments.
DRAWER HANGER
SMALL DRAWER DIVIDER
HARDWARE IDENTIFICATION
1BOLT
(M6 x 100mm - BLK) 8PCS
2
3
LOCK WASHER
(1.6 x 14mm - BLK)
FLAT WASHER
(1 x 18mm - BLK)
8PCS
8PCS
4ALLEN WRENCH
(M4 x 65mm - BLK) 1PC
5FLAT HEAD SCREW
(8 x 38mm - BLK) 8PCS
NOTE:
Philips head screw driver is required in the assembly process; however, manufacturer does not provide this item.

ITEM: 881284
COASTERFURNITURE.COM
PAGE 3 OF 5
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
PART # B ~ E INSIDE
A
A
B
5
4
3
1
2

STEP 4
COMPLETE
ITEM: 881284
COASTERFURNITURE.COM
PAGE 4 OF 5
ASSEMBLY INSTRUCTIONS
STEP 3
LEVELER
E
D
C

881284
File Cabinet
COASTERFURNITURE.COM
PAGE 5 OF 5
ITEM: 881284
ANTI-TIPPING INSTALLMENT INSTRUCTIONS
Injury may result from tipping furniture.
WARNING
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the short screw.
2. Determine where the furniture is to be to placed and mark location on the wall for the mounting bracket
screw hole approximately 2” below the bracket mounted to the edge of the furniture.
3. Drill a 3/16” hole in the wall. Press the plastic wall plug into the hole and gently tap until the flange on
the wall plug is against the wall surface.
4. Position the bracket over the wall plug and use the long screw to securely attach the bracket to the wall.
5. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
6. Lace an end of the cable tie down through each bracket. Bring both ends together and slide the
beaded end of the cable tie through the keyhole shaped slot on the other end untill snug. Pull down
on the beaded end until it snap locks into the keyhole slot.
7. To double lock return the beaded end back through the keyhole as shown.
8. Check to make sure the cable tie is securely laced and locked to the brackets.
FURNITURE TIPPING RESTRAINT

COASTERFURNITURE.COM
ITEM: 881284
NOTE: Dimension tolerance + 5%
-
INNER SIZE OF DRAWER (A) : 15.2” x 17.8” x 1.8”
INNER SIZE OF DRAWER (B) : 15.2” x 17.8” x 3.6”
INNER SIZE OF DRAWER (C) : 15.2” x 17.8” x 9.6”
INNER SIZE OF DRAWER (D) : 15.2” x 17.8” x 9.6”
2.8”
4.9”
11”
31”
24”
42”
11”
11.2”
17.2”
3.7”
27.6”
10”
A
B
C
C
D
23.7”
41.4”