Your Detector
Mode Tone Display/Voice Result
Set
IntelliShield
City mode
default*
Two beeps City X Asingle beep sounds when the
signal is first detected.
One beep City X
beep Off Audio for all X band alerts are blocked
until signal strength reaches Level 3.
One beep City X+K Combines the City X mode with
prevention of K band audio alerts
until signal strength reaches Level 2.
IntelliMute
mode Two beeps IntelliMute On All alerts (except for strobe signals
from emergency vehicles) are
automatically muted below the
engine rev point you set.
One beep IntelliMute Off Normal operation.
Set
IntelliMute
RPMs
One beep Set IntelliMute
(see page 15
to set activation
point)
Allows you to set the engine
rev point while using IntelliMute.
Note: Only shown if IntelliMute is Off.
IntelliMute
Pro mode Two beeps IntelliMute Pro
On All radar, VG-2 and Spectre detection is
turned Off below the engine rev set point.
One beep IntelliMute Pro
Off Normal operation.
Auto Mute
mode Two beeps AutoMute On The audio volume of all alerts will be
automatically muted after four seconds for
as long as the signal is detected.
One beep AutoMute Off All alerts will sound at full volume
for as long as the signal is detected.
Set
Compass One beep Set Compass Allows you to calibrate the compass.
(see page 18 to calibrate compass)
Pop Detect
mode Two beeps Pop Detect On Unit will detect Pop signals.
One beep Pop Detect Off Unit will not detect Pop signals.
This EasySet programming menu lists all of the modes and settings you can
choose from after you have entered Program mode as described on page 7. Mode Tone Display/Voice Result
VG-2 Detect
mode Two beeps VG-2 Detect On Unit will detect VG-2 signals.
One beep VG-2 Detect Off Unit will not detect VG-2 signals.
VG-2 Audio
mode (not
shown if VG-2
detect is Off)
Two beeps VG-2 Audio On With VG-2 Detect On, the unit will give
audible alerts for VG-2 signals.
One beep VG-2 Audio Off With VG-2 Detect Off, the unit will give
only visual alerts for VG-2 signals.
Spectre
Detect mode Two beeps Spectre
Detect On Unit will detect Spectre I & IV+ signals.
One beep Spectre
Detect Off Unit will not detect Spectre I & IV+
signals.
Spectre
Audio mode
(not shown
if Spectre
detect is Off)
Two beeps Spectre Audio
On With Spectre Audio On, unit will give
audible alerts for Spectre signals.
One beep Spectre Audio
Off With Spectre I Audio Off, unit will give only
visual alerts for Spectre I & IV+ signals.
SmartPower
mode Two beeps SmartPower On SmartPower is On.
One beep SmartPower Off SmartPower is Off.
XBand
Detect mode Two beeps XBand On Unit will detect X Band signals.
One beep XBand Off Unit will not detect X Band signals.
Kor Ku Band
Detect mode Two beeps Kor Ku Band On Unit will detect K or Ku Band signals.
One beep Kor Ku Band Off Unit will not detect K or Ku Band signals.
Set display
Dim mode
default*
Two beeps Display Dim Partially dimmed for dusk or night driving.
One beep Display
Dimmer More dimmed for dusk or night driving.
One beep Display Dark Display is Off.
Restore factory
settings One beep Restore Factory
Settings Resets user modes and settings to
factory default.
Exit program One beep EXIT PROGRAM Allows you to exit Program mode.
*The settings for these user modes can also be changed
with the one button method.See description of each user
mode (pages 10 and 25) for details.
Nothing Comes Close to a Cobra®9
