Code Alarm Power Elite PC 4100 User manual

1
Installation
Instructions
Avoid mounting components or
routing wires near hot surfaces
Avoid mounting components or
routing wires near moving parts
Tape or loom wires under hood
for protection and appearance
Use grommets when routing wires
through metal surfaces
Use a voltmeter for testing and
verifying circuits
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking
keys in vehicle during installation
PC 4100
100414-8
Technical Support
24 Hours/ 7 Days per Week
For Authorized Dealers - [phone]
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of Industry
Canada.Operationissubjecttothefollowingtwoconditions:
1.Thisdevice may not cause harmful interference, and
2.This device must accept any interference received, including interference that
maycauseundesiredoperation.
Warning!
Changesor modifications not expressly approved by the party responsible for
compliancecouldvoidtheuser’sauthoritytooperatetheequipment.

2
System Layout
System Layout Power Elite PC 4100TM
Security
A = Advanced Harness (Optional)
B = Basic Harness (24 pin)
Note: The wire connection sections will identify each wire with a
number (pin cavity) and a letter (harness), i.e.: 20/B = Wire 20,
B (Basic) Harness. View from wire end:
1234
PATS/VATS HARNESS
12345
EXTENDED RANGE HARNESS
Advanced Harness (Optional) Basic Harness
1. LockSwitch(87a)(BLUE/BLK) 1. ParkingLightOutput(WHITE)
2. Unused 2. LockMotorOutput(BLUE)
3. UnlockSwitch(87a)(GRN/BLK) 3. Unused
4. Unused 4. Battery(+12v)(RED)
5. Unused 5. Ground(BLACK)
6. Unused 6. StarterKey(+)(VIOLET/RED)
7. Unused 7. Ignition1Input`(+)(PINK)
8. Unused 8. StarterMotor(+)(VIOLET)
9. TrunkSwitch(87a)(TAN/RED) 9. Unused
10. Unused 10. MultiplexOutput(YL/WHT)
11. Unused 11. Unused
12. Unused 12. Unused
13. Unused 13. TrunkMotorOutput(TAN)
14. Unused 14. UnlockMotor(GREEN)
15. Unused 15. Siren Feed(+12v)(PLUG-IN)
16. DoorTrig10kPull-up(RED) 16. Horn/SirenDrive(-)1Amp (PLUG-IN)
17. Disarm/OverrideButton(Ground)(PLUG-IN)
18. Disarm/OverrideButtonInput(PLUG-IN)
19. HoodPinInput(-)(GRAY)
20. DoorTrigger(GRN/VT)
21. Unused
22. LED2(Red)(PLUG-IN)
23. LED1(Black)(PLUG-IN)
24. SecondDoorUnlock(-)500ma(BLU/GRN)
01112131 415161314151617181 91021222324278 901
123456789123456789 011121123456
IMPORTANT!!!
The module MUST be programmed before it will operate.
Refer to the programming instructions on pages 11-13.
FOR MODULE FUSE SIZE AND POLARITY
LOCATIONS, REFER TO CHART ON PAGE 10.

3
1. Basic Harness (B)
IMPORTANT!!!
• Remove fuses from Module before installation.
• Solder and tape all connections.
1/B Parking Light Output (20 AWG) (WHITE)
Locate the vehicle parking light wire.
Verification: This wire will register either positive voltage or ground
when the parking lights are turned on.Voltage does not vary when
dimmer switch is adjusted. Refer to the Vehicle Wire Color and
Location Chart for the wire color, polarity, and location.
Connect the 1/B wire to the parking light wire.
IMPORTANT!
After installation, set the polarity of this circuit by moving the
fuse inside of the control module to positive (+) or negative(-).
Use the following diagrams for door locks or purchase the
Advanced Harness and utilize the on-board relays.
2/B Lock MotorWire (20 AWG) (BLUE)
14/B Unlock MotorWire (20 AWG) (GREEN)
24/B Second Door Unlock (20 AWG -) (BLUE/GREEN)
IMPORTANT!
Afterinstallation, setthepolarityof thiscircuitby movingthe
fuse inside of the control module to positive (+) or negative(-).
Type 1: Positive 3-wire door lock system -
Polarity Fuse = Positive (+)
Single-stage unlock
Connect the 2/B wire to the vehicle
lock wire.
Connect the 14/B wire to the vehicle
unlock wire.
Two-stage unlock
Connect the 2/B wire to the vehicle
lock wire.
Use a SPDT relay (not supplied)
and connect the 24/B wire to the
vehicle unlock wire as shown in Diagram 1.
86 87 85
30
87a
Fused + 12v
To vehicle unlock wire
Diagram 1
24/B

4
Connect the 14/B wire as shown in Diagram 2.
Type 2: Positive 5-Wire Door Lock System
Polarity fuse = Positive (+)
Single-Stage Unlock
Connect wire 2/B as
shown in Diagram 3.
Connect wire 14/B
as shown in
Diagram 4.
Two-Stage Unlock
Connect wire 2/B as
shown in Diagram 3.
Use a SPDT relay
(not supplied) and
connect the 24/B
wire to the vehicle’s
unlock wire as
shown in Diagram 5
(page 5).
Connect wire 14/B
as shown in
Diagram 2 (above).
1. Basic Harness (B), cont’d.
X
86 87 85
30
87a
12v
Diagram 2
14B Unlock
Ground
From Driver’s Door Only
Unlock Switch or Relay To Driver’s Door Unlock Motor
CUT HERE
X
86 87 85
30
87a
CUT HERE
14B
Ground
Unlock MotorUnlock Switch
Unlock
Diagram 4 Fused + 12v
X
86 87 85
30
87a
Diagram 3
CUT HERE
2B
Ground
Door Lock Switch Door Lock Motor
Lock
Fused + 12v

5
Type 3: Negative 3-Wire Door Locking System
Polarity Fuse = Negative
Single-stage unlock
Connect the 2/B wire to the vehicle lock wire.
Connect the 14/B wire to the vehicle unlock wire.
Two-stage unlock
Connect the 2/B wire to the vehicle lock wire.
Connect the 24/B wire to the vehicle unlock wire.
Use a SPDT relay (not supplied) and refer to Diagram 6 to connect
to the vehicle’s driver’s unlock wire.
1. Basic Harness (B), cont’d.
86 87 85
30
87a
X
24/B
Fused +12v
From Door Unlock
Switch To Door Unlock Motor
Diagram 5
X
86 87 85
30
87a
CUT HERE
Fused + 12v
Diagram 6
14/B
Fused + 12v
From Driver’s Door Only
Unlock Switch or Relay To Driver’s Door Unlock Motor

6
Diagram 7
2B
Ground
14B
12v
To Control Pump
LOCK
UNLOCK
Type 5: Resistor Door Lock system
Polarity Fuse = Positive/Negative
Note: Refer to Vehicle Wire Color and Location Chart for correct
polarity. Move the fuse inside of the control module to positive or
negative polarity.
Single Stage Unlock
Diagram 8
MODULE
WIRES
TO DOOR LOCK MODULE
2 / B Lock
14 / B Unlock
Master
Vehicle
Door Lock
Switch
or Plunger
1. Basic Harness (B), cont’d.
Type 4: Vacuum Door Lock System
Polarity Fuse = Negative
Note: Two-stage unlock will not work with this type of system.

7
Two-Stage Unlock
Connect the 2/B wire as shown in Diagram 8 (page 6).
Connect the 24/B wire as shown in Diagram 9 (below).
Connect the 14/B wire as shown in Diagram 10 (below).
1. Basic Harness (B), cont’d.
86 87 85
30
87a
Ground for negative
polarity system
+12v fused for
positive polarity
system
+12v fused
To vehicle door lock module
24/B
Diagram 9
86 87 85
30
87a
X
From Driver’s Door
Only Unlock Switch
14/B
+12v fused
Cut
To Driver’s Door
Only Unlock
Motor
Diagram 10
Ground for positive
polarity system
+12v fused for
negative polarity
system

8
1. Basic Harness (B), cont’d.
4/B Main Power (14 AWG) (RED)
Connect the 4/B wire to the vehicle main power wire at the ignition switch.
Verification: This wire registers voltage through every position of
the ignition switch.
5/B Chassis Ground (14 AWG) (BLACK)
Connect the 5/B wire to a solid chassis ground point. Scrape
away paint from the grounding point to ensure a good connection.
Note: Do not ground the 5B wire with any other vehicle components.
6/B Starter Input Key Side (14 AWG) (VIOLET/RED)
8/B Starter Output Motor Side (14 AWG)(VIOLET)
Locate the vehicle starter wire.
Verification: This wire registers voltage only when the key is turned
to the START position.
Cut the vehicle starter wire in half.
Verification after starter wire is cut:
•KEY SIDE of starter wire registers voltage when the key is turned
to the START position.
•MOTOR SIDE of starter wire registers no voltage.
Connect the 6/B wire to the KEY SIDE of the vehicle starter wire at
the ignition switch harness.
Connect the 8/B wire to the MOTOR SIDE of the vehicle starter wire.
7/B Ignition 1 Input (14 AWG+) (PINK)
Connect 7/B wire to the vehicle ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to
the ON (or RUN) position.The voltage does not drop out when the
key is turned to the START (or CRANK) position.
13/B Trunk Release Output (TAN)
Locate the vehicle trunk release wire.
Verification: Refer to the VehicleWire Color and Location Chart
for the wire color, polarity, and location.
Connect the 13/B wire to the vehicle trunk release wire.
IMPORTANT!
After installation, set the polarity of this circuit by moving the
fuse inside of the control module to positive (+) or negative(-).

9
16/B Horn Relay Drive 500 ma (20 AWG -)
Locate the vehicle horn wire.
Verification: This wire will register
either positive or ground when the
horn is pressed.
Connect the 16/B wire to the vehicle
horn wire if the system is negative.
If the system is positive, use a SPDT
Relay (not supplied) and connect the
16/B wire to the vehicle horn wire as
shown (Diagram 11).
If you are installing a siren:
15/B, 16/B Siren Installation (20 AWG)
Mount siren with bell housing facing down.
Use at least two (2) screws to secure siren to mounting location.
Connect siren BLACK wire to 16/B Horn/Siren drive.
Connect siren RED wire to a 15/B siren feed.
Select output to be “Siren Output” in Option Bank 1/Feature 7
on page 13.
17/B, 18/B Emergency Override Button (20 AWG-)
Find a mounting location for the override button that is not easily
seen or openly accessible.There must be at least 1" clearance
behind the location.
Drill a 9/32" hole and mount the button.
Connect one of the override button BROWN wires to the 17/B wire.
Connect the other override button BROWN wire to the 18/B wire.
19/B Hood Safety Input (20 AWG -) (GRAY)
Install the supplied pin switch and attach the 19/B wire.
Verification: When connected, the 19/B wire will register ground
when the vehicle hood is opened.
1. Basic Harness (B), cont’d.
86 87 85
30
87a
+12 Volts
16/B
To Horn Wire
Diagram 11

10
20/B Positive/Negative Door Input (20 AWG) (GREEN/VIOLET)
Connect the 20/B wire to the vehicle pin switch or courtesy light
circuit.
Verification - Refer to VehicleWire Color and Location Chart for circuit
type and location, or verify the vehicle wire using the following guideline:
• Positive Systems - Target wire registers voltage
when any door is opened.
• Negative Systems - Target wire registers ground
when any door is opened.
Important!
After installation, select the polarity of this circuit in programming
Option Bank 2/Feature 1 (factory default = negative), page 13.
NOTE:
FOR POSITIVE SYSTEMS, TEMPORARILY CONNECT THE 20/B WIRE TO GROUND
IN ORDER TO ACCESS THE PROGRAMMING MODE. REFER TO PAGE 11.
CHANGE OPTION BANK 2/FEATURE 1 TO POSITIVE POLARITY (PAGE 13).
22/B LED2 (20 AWG+)
23/B LED1 (20 AWG-)
Locate a visible section of the dash with 1" clearance behind
the location.
Drill a 9/32" hole and snap the Status Indicator into place.
Connect the Status Indicator Red Wire to the 22/B LED2 wire.
Connect the Status Indicator Black Wire to the 23/B LED1 wire.
Tip: To change the Red LED to a Green LED:
Connect the status indicator Black wire to the 22/B LED2 wire.
Connect the status indicator Red wire to the 23/B LED1 wire.
1. Basic Harness (B), cont’d.
Fuse Size & Location
Trunk
Output Dome Light Parking Lights
Door
Locks
|| || ||
||
|| || ||
||
|| || ||
||
|| || ||
||
|| || ||
||
Heater 1 Heater 2 Ignition 1/2
Main Power
15A 15A 15A
25A
+ + +
+
_ _ _
_
25A 25A 25A
5A