Code Alarm TW-1 User manual

)
Cccc~l.Ar:lm·
Technology that talks to cars and trucks,"
Remote Vehicle Control System
Two Way Remote Start
& Security
IMPORTANT NOTE: The opsr<!.tion of the TW-1 as described in this
manual Is applicable to most vehicles. However. due tothe engine type
and configuration of some vehicles (l.e. diesel engines). sO(lle functions
ANDIOR SAFETY PRECAUTIONS may not apply. Please see your
Installing dealerfor more informallon. 101513-0
)

TABLE OF CONTENTS
Users' Precaution
) The remote LCD icons with functions ................................................................1-2
Operation guide of TW1 unit .................................................................................4
Pre-assigned function modes by remote's buttons ...............................................4
Programmed function modes by a short press of button [ I ] ............................4
Self-defined functions by a short press of button [II] .......................................5
Door Lock/arm..................................................:..................................................5
Defective zone bypass.........................................................................................5
Door unlock/disarm .............................................................................................6
Security diagnostic report....................................................................................6
Parking light flash upon door open .....................................................................6
Auto relock ...................._....................................................................................6
Door Lock/unlock ................................................................................................6
Auto door lock/unlock upon ignition on/off ..........................................................6
Active channel # 3...............................................................................................7
2 Steps door unlock /disarm................................................................................7
Remote engine start.......................................................................................... 7-8
Remote change of engine
run time.....................................................................8
Remote engine shut off.......................................................................................8
Remote temperature start ON/OFF.....................................................................9
Remote check current auto-start temperature setting.................................... :: ... 9
Daily auto-start time ON/OFF..............................................................................9
Remote check car indoor temperature/Status ...................................................10
Active channel # 1 for release trunk............................·........................................10
Remote siren/horn alert ON/OFF........................................................................10
Active channel # 2....................................................:.......................................... 11
Car locator/search............................................................................................... 11
Shock sensor by pass......................................................................................... 11
Alarm mode & warn away................................................................................... 11
Light impact trigger. .. ......................................................................................12
A

/
Heavier impact trigger.........................................................................................12
Door/hood /trunk open trigger ............................................................................12
Remote Panic......................................................................................................12
Remote anti-carjack ON/OFF..............................................................................12
Switch-controlled anti-carjack ON/OFF...............................................................13
Remote valet ON/OFF ........................................................................................13
Programmable function
by over-ride switch ........................................................ 14
Page-out call .......................................................................................................14
Manual ARM and DISARM .............................................................................14-15
Procedures of remote start for manual transmission gear car............................ 15
How to learn codes of the remote transmitter .....................................................15
Dash LED status indicator...................................................................................16
Replacement of battery.......................................................................................16
Programming of remote control unit....................................................................
17
B

)
)
TW-1 ICONS AND FUNCTIONS
• The alphabetical signs indicate the function modes
A. Remote anti-carjack mode ON/OFF
B. Remote control channel # 3 for
electrical appliance ON/OFF
c. Remote activate temp-controlled
auto-start mode ON/OFF
D. Remote activate daily auto-start time
mode ON/OFF
E. Remote engine start (or) changing of
run time when the engine gets
G. Remote activate Audible arm mode
ON/OFF
H. Remote shock sensor bypass mode
ON/OFF
I. Remote activate valet mode
ON/OFF
J. Remote monitor in-car temperature
& status
K. Remote control channel # 2 for
electrical appliance ON/OFF
L. Remote trunk release

J
• The numerical signs indicate the vehicle's security status or
other function display
1. Remote's battery condition
2.
Channel # 2 On/OFF
3. Temp-controlled auto-start mode
4. Engine run mode
5. Trunk release
6. Door open
7. Remote unit's vibration mode
8. Valet mode
9. Auto rearm mode
1
O.Mute alert mode
11.Audible alert mode
12.Hood open mode
13.lmpact/shock mode
14.Hand-brake disengage
15.Door lock mode
16.Door unlockmode
17.Monitor standby mode
18.Feedback confirmation (Alter each
command by remote unit; display of
this confirms feedback can be picked
up by remote unit. Non-display
means remote
is either out-of- range
or feedback is being interfered.
19.Page out-call from car
20.Power save mode of remote(Absolute
current sleep 'mode of the remote,
after system is disarmed)
21.lgnition On mode
22.Alarm clock mode
23.P.M time mode
24.A.M. time mode
25.Daily auto-start time mode
26.Hour, minute, temp. display
27.Centigrade, Celsius mode
28.Count-down time mode
2

TW-1 User's manual 2 Way remote security system
• Precaution before installation
1. Read this manual carefully ahead of operation. You will find this product very
versatile.
2. Park the vehicle in open space each time if the remote start is intended .This avoids
you from being suffocated by the exhaust gas while the engine gets running.
3. For safety purpose, set your car to valet mode "ON" before sending it to workshop for
serviced
4. There are many other functions ,Refer to the installation manual for such extra
functions that require external accessories.
5. You are suggested to refer to the "options Program Table" whenever you find[options
program
table] in the text on the installation manual.
• Special features:
1. Choice of function mode by cursor on screen for easiest operation (patented
features)
2. 2 Way Super-remote control/monitoring range [Effective range of approx
800-1200 m]
3. Electronic luminescent backlight
4. Hopping code for anti-grabbing
5. Main system's memory able to learn codes from 4 different remotes
6. Remote control of lock/unlock, arm/disarm, engine start, trunk release and etc.
7. Switch-accessed Arm/disarm for emergency
8. Selectable mode for auto/manual transmission gear with safety circuit
9. Selectable rnode for gasoline and diesel engine
10. Programmable for temp-controlled auto-start
11. Programmable for daily auto start time
12. Remote monitoring of car status lin-car temperature
on display
13. Display
of defective zones bypass when arming
14. Display
of remote shock sensor bypass
15. Smart temper report by siren when disarmed
16. Remote control electrical appliances through channel # 1,#2 ,#3
17. The main system temporarily by-passes shock sensor at the moment the remote
trunk release is activated
18. Remote control & switch-activated anti-carjack modes
19. Remote panic
20. Remote or manual valet mode
21. Other system's functions accessible by software program
22. LED status indicator to assist programming and anti-theft warning
3

.. J
)
Operation guide of TW-1
This is devised for easy operation just by somel fixed functionl by buttons and
Imovable cursor meansj. Users can choose the desired function just by first popping
out the cursor and then
moving it on to the related function Position.
There are total 3 buttons marked with [I ' II ' ill] on the remote unit. The [ I ' II]
buttons are used in alarm function mode setting and the third [ill] button is used in
popping out and
moving of the cursor on to the desired function position.
* Pre-assigned function modes by remote's buttons
Remote's button [I]: Press and hold this for engine-start and shutoff
Remote's button [
II] : Press and hold this for trunk release.
Remote's button
[I] [ II] : Press and release both [ I ] & [II] simultaneously for
car find.
Remote's button
[1][ II ]: Press and hold both[ I ] &[ II ]simultaneouslyfor remote
panic
* Programmed function modes by a short press of button [ I ]
Press and release this to activate self-defined function .It is generally programmed for
door lock/unlock. Other functions can also
be programmed as below:
Step 1: Press button [ill] twice or more times quickly to pop up the cursor. Move the
cursor to the desired position
by pressing button [ill] a number times as
~
necessary. For example, move the cursor on to r t::;I J position, if you want to
have "Audible Arm Mode" function activated by a short press of button [ I ] .
Step 2: When the cursor reaches the desired position, press and hold [ill] again for 6
sec till the remote unit sounds the first 2 and final 3
beeps. From then on, press
and release button [ I] to activate the selected function.
* To re-define the function of button[ I ]re-do the procedure from procedure step (1)
& (2).The previously-defined function mode will be substituted by the last definition.
4

* Self-defined functions by a short press of button [II]
Press and release button [1I] to activate self-defined function .It is generally
~
programmed to assign rJQJ for Mute Arm Mode. other functions can also be
programmed as below:
Step 1 : Press button [ill] twice or more times quickly to pop up the cursor. Move the
cursor
to the desired position by pressing button [ill] a number times as
~
necessary. For example, move the cursor on to r\,$l:JJ , if you want to have
" Status Check" function activated by a short press of button [1I] .
The following 2 way remote's function guide is based on the current
cursor setting in the above passage
1. IRemote arm & door lock I
(a) , Shut off the engine, get out of the car making sure handbrake is depressed, hood
closed and all the door closed.
(b) , Press and release button [ I] the system will lock the door and enter arm mode
with 1 siren chirp and 1 parking light flash.
• The remote unit sounds melody and displays r Q J r(<<" J icons on its screen.
(c) , Press and release button [1I] the system will lock the door and enter arm mode
with 1 siren chirp and 1 parking light flash.
• The remote unit sounds melody and displays r e lr({i)jI Jicons on its screen which
means the system
is in mute arm mode.
(d) , Defective zone
report and bypass arming: When arming, if the system detects
defective zones, the system will sound 4 siren chirps or the remote unit sounds 4
beeps twice. The remote unit displays on its screen the defective zone ( like the
door open).The system then will bypass the defective zone and can enter arm
mode. When the defective zone
is corrected ( just by closing the door later ), the
system immediately enters full
arm mode.
(e) , Arm
delay time can be programmed: ( like 6 or 30 sec daily arming after door is
closed) as needed. [option program table]
5

2. IRemote disarm & door unlock I
(a) -Press and release the button [ I] or [IT] the system will unlock the door and
disarm itself with 2 siren chirps and 2 car light flashes. The dome light will turn
on .( Refer to installation manual for dome light features that needs external relay)
• The remote unit sounds 2 beeps and
displays' iii ~ icon on its screen
(b) -Smart zone trigger report: Should there be any abnormal security status while in
arm mode, the siren sounds 4 chirps or the remote sounds 4 beeps when the
remote unit's button
[I] is pressed. The trigged zone during arm mode is
displayed on the remote unit's screen.
(c) -Parking light flash upon door-open: Each time the car door is opened following
disarm, the parking light flashes for 10 sec
to caution other vehicles coming behind.
[option program
table]
(d) -Auto rearm: This is programmable to have your system rearm itself if the car door is
not opened after
30 sec from the time of remote disarm [ option program table]
3. IRemote door lock/unlock I
(a) Press and release button [ I ] while driving, the system will unlock/lock with parking
light flash.
• The remote unit displays
'd ~ for the door unlock or displays' 6 ~ for door lock.
* You can also program to have door lock/unlock upon ignition ON/OFF. [option
program table ]
6

J
/)
J
IRemote control channel # 3 I(option program table ]
(a) , If the system is programmed for channel #3 mode ( an external relay is
required)
(b) , Press quickly
(ill] twice or more rimes to pop up cursor and then move
Wit onto [B3]
).
(c), Then press and release[ IT] .The system responses in accordance with
Single selected function mode .The parking light flashes 3 times for confirmation.
Option • The remote unit displays Car Status
on its screen and sounds 3 beeps
( ChooseI2 stage
door unlock, disarm I(option program table ]
only one
(a) , If the system is programmed channel # 3 for 2 stage door unlock mode.
of these) (
an external accessory is required)
(b) , Press quickly
[ill] twice or more times to pop up the cursor and then
W
move it onto (B3] )
(c) , Then press and release (
IT] to unlock all the doors. The system will
unlock
and disarm with 2 siren chirps and 2 parking light flashes.
• The remote unit displays •U
~ on its screen and sound 2 beeps.
"" Choose one of the above two options and program ·It as required.
4, IRemote engine start I
(a) , The engine is in shut off state.
(b)' Press and hold ( I] button. Or press IT button when the active cursor is shifted
onto the
d;b the column. Siren chirps 3 times with 3 parking light flashes when the
engine gets started.
• The remote unit displays 2 stages on its screen as below:
(1) , In the 1st stage: The remote unit displays the current status along with
• 51:: ~ while engine is trying for engine start and sounds.
(2)' In the 2
nd
stage: After the engine gets started, the remote unit displays
along with engine's preset run tirne and sounds.
7
-
Ii" ... _ .!l