Code Alarm PROFESSIONAL SERIES User manual

12020 Voxx Electronics Corporation. All rights reserved.
PROFESSIONAL
SERIES
Security and Keyless Entry
Installation Guide
ca1045
**This guide is a reference for module rmware version 5.0 or higher**

2ca1045 rev B
Before You Begin.........................................................................................3
Wire Connection Guide............................................................................... 4
5 Pin Main Harness ................................................................................... 5
6 Pin Input / Output Harness .....................................................................6
2 Pin Door Lock Output Harness ............................................................... 8
Additional Ports.........................................................................................12
LED Port ..................................................................................................12
Programming Port ................................................................................... 12
On-Board Shock Sensor .........................................................................12
DBI Port ...................................................................................................12
Set Up & Programming ............................................................................. 13
Transmitter Programming ........................................................................13
Manual Feature Programming ................................................................. 13
Programming Feature Banks ..................................................................14
PC Based Feature Programming / Firmware Updates - (Optional) ......... 16
Dome Light Delay / Theater Dimming ..................................................... 16
Chirp Delete - User Accessible ................................................................ 17
User Selectable LED ............................................................................... 17
Feature Descriptions................................................................................. 18
Transmitter Button Functions .................................................................. 22
Security Trigger Zones.............................................................................. 22
System Layout...........................................................................................23
Table of Contents

32020 Voxx Electronics Corporation. All rights reserved.
PROFESSIONAL INSTALLATION
STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Technical Support [phone]
or go to
www.voxxuniversity.com
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
“COMPUTER SAFE PROBE” as these can set o󰀨 air
bags or damage vehicle computers.
Use grommets when routing wires through metal
surfaces
BEFORE YOU BEGIN

4ca1045 rev B
6 Pin Input / Output Harness
5 Pin Main Harness
2 Pin Door Lock Output Harness
1WHITE/REDPARKING LIGHT INPUT
2WHITE PARKING LIGHT OUTPUT
3BLACKGROUND
4BROWNSIREN / HORN OUTPUT
5REDBATTERY 12V ( + )
5 PIN MAIN
1PURPLE DOOR TRIGGER INPUT ( + )
2BLUE TRUNK PIN INPUT ( - )
3GREEN DOOR TRIGGER INPUT ( - )
4YELLOWIGNITION INPUT ( + )
5ORANGE GROUND WHEN ARMED OUTPUT ( - )
6RED/WHITETRUNK RELEASE OUTPUT ( - )
6 PIN INPUT / OUTPUT
1BLUE UNLOCK ( - )
2GREEN LOCK ( - )
2 PI
N
LOCK

52020 Voxx Electronics Corporation. All rights reserved.
3 BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface in
the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
5 Pin Main Harness
1 WHITE/RED PARKING LIGHT INPUT
2 WHITE PARKING LIGHT OUTPUT
Locate the parking light output wire at the vehicle’s light switch.
  Verication: This wire registers positive voltage when the parking lights
are turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
4 BROWN SIREN / HORN OUTPUT
This output is available to be used as a constant ( + ) siren output OR a pulsed
( - ) horn output and is selectable by changing the jumper position on the main
module. Refer to the system layout on page 22 for location.
SIREN:
Connect the BLACK siren wire to a chassis ground using a ring terminal and self
tapping screw (not supplied).
Route the BROWN siren output wire from the control module through the rewall and
connect to the RED wire on the siren.
NOTE: Be sure to loom the siren wires, and seal the grommet.

6ca1045 rev B
5 RED BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
 Verication:This wire will register ( + ) voltage in all positions of the
ignition switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
6 Pin Input / Output Harness
1 PURPLE DOOR TRIGGER INPUT ( + )
Locate the vehicle’s dome light or door pin switch wire.
 Verication:This wire will register positive voltage (POS) when the door is
opened and the interior light is on. This wire will
register ground or “0” Volts when the door is closed and the interior light is
o󰀨.
Connect the PURPLE wire to the vehicle’s positive door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide
2 BLUE TRUNK PIN INPUT ( - )
Locate the vehicle’s trunk pin switch wire and connect to the BLUE wire.
 Verication:This wire when connected will register ground when the
vehicle’s trunk is opened.
Connect the BLUE wire to the trunk pin.
HORN:
Locate the vehicle’s horn wire.
 Verication:This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN wire to the vehicle’s horn wire. This is a low current output,
300mA.

72020 Voxx Electronics Corporation. All rights reserved.
5 ORANGE GROUND WHEN ARMED OUTPUT ( - )
This wire will have a continuous ( - ) 500mA output when the system is Armed. This
wire is typically used for controlling window modules or additional sensors.
4 YELLOW IGNITION INPUT ( + )
Locate the vehicle’s ignition wire at the ignition switch.
  Verication:This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START (or CRANK) position.
Connect the YELLOW wire to the vehicle’s Ignition wire.
6 RED/WHITE TRUNK RELEASE OUTPUT ( - )
Locate the vehicle’s trunk release wire at the trunk release switch.
 Verication:This wire will register either positive voltage or ground when
the trunk release is activated.
This is a low current output, 200mA.
3 GREEN DOOR TRIGGER INPUT ( - )
Locate the vehicle’s dome light or door pin switch wire.
 Verication:This wire will register ground (NEG) when the door is opened
and the interior light is on. This wire will register positive voltage when the
door is closed and the interior light is o󰀨.
Connect the GREEN wire to the vehicle’s negative door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle
application guide

8ca1045 rev B
2 Pin Lock Output Harness
1 BLUE UNLOCK ( - )
2 GREEN LOCK ( - )
The door lock / unlock outputs are designed to control several di󰀨erent types of
systems which may require additional parts. Please review the wire and location
chart to see which type of door lock system is in your vehicle. The most common
types are shown in the following diagrams.
Negative Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: These wires will register ground when the Lock and Unlock
switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Lock
Unlock
Vehicle Door Lock
Control Relays
GREEN ( - ) Lock Output
BLUE ( - ) Unlock Output
Negative Locks:

92020 Voxx Electronics Corporation. All rights reserved.
Positive Switching Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: These wires will register positive voltage when the Lock and
Unlock switches are activated.
Connect the GREEN and BLUE wires shown in the diagram below.
Reverse Polarity Locks (5-Wire Door locks)
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: These wires will rest at ground and register positive
voltage when the Lock and Unlock switches are activated.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below
using (2) SPDT relays (not supplied).
Lock
Unlock
87
87a
86 85
30
87
87a
86 85
30
Fused +12 Volt
Battery Souce
Fused +12 Volt
Battery Souce
GREEN ( - ) Lock Output
BLUE ( - ) Unlock Output
Reverse Polarity Locks:
X
Cut
X
Cut
To Door Lock Motor
To Door Lock Motor
Lock
Unlock
87
87a
86 85
30
87
87a
86 85
30
Vehicle Door Lock
Control Relays
Fused +12 Volt
Battery Souce
Fused +12 Volt
Battery Souce
GREEN ( - ) Lock Output
BLUE ( - ) Unlock Output
Positive Locks:

10 ca1045 rev B
Negative Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: This wire will show variable ground when the switch is activated.
Please consult the wire and location chart for specic resistor values for
your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below
using (2) SPDT relays (not supplied).
Positive Multiplexed Locks
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock
switch.
  Verication: This wire will show variable positive voltage when the switch is
activated. Please consult the wire and location chart for specic resistor
values for your vehicle.
Connect the GREEN and BLUE or BLUE/GREEN wires shown in the diagram below
using (2) SPDT relays (not supplied).
Lock
Unlock
Vehicle Door Lock
Control Relays
GREEN ( - ) Lock Output BLUE ( - ) Unlock Output
Multiplex Locks:
87
87a
86
30
87
87a
86
30
85 85
Fused +12 Volt
Battery Source
Resistor
Lock
Unlock
Vehicle Door Lock
Control Relays
GREEN ( - ) Lock Output BLUE ( - ) Unlock Output
Multiplex Locks:
87
87a
86
30
87
87a
86
30
85 85
Fused +12 Volt
Battery Source
Ground
Resistor