Coemar LEDko EXT FullSpectrum RGBLA User manual

EXT
FullSpectrum RGBLA

2
Please note in the space provided above the relative service information of the model and the retailer from whom
you purchased your LEDko EXT FullSpectrum RGBLA: this information will assist us in providing spare parts,
repairs or in answering any technical enquiries with the utmost speed and accuracy.
WARNING: the security of the fixture is granted only if these instructions are strictly followed; therefore it is
absolutely necessary to keep this manual.
Serial Number:
...................................................................................................................................................................................................
Purchase date:
...................................................................................................................................................................................................
Dealer:
...................................................................................................................................................................................................
Address:
...................................................................................................................................................................................................
Suburb:
...................................................................................................................................................................................................
Country:
...................................................................................................................................................................................................
Phone / Fax:
...................................................................................................................................................................................................
User Manual version 1.4
Edition January 2020
EXT
FullSpectrum RGBLA

3
Index
1. Packaging and transportation ................................................................................................................................Pag. 5
1.1 Packaging ...........................................................................................................................................................Pag. 5
1.2 Transportation ...................................................................................................................................................Pag. 5
2. General information .............................................................................................................................................. Pag. 5
2.1 Safety informations .......................................................................................................................................... Pag. 5
2.2 Warranty conditions ........................................................................................................................................ Pag. 6
2.3 EC norms ......................................................................................................................................................... Pag. 6
3. Product specifications .............................................................................................................................................Pag. 7
3.1 Technical characteristics ...................................................................................................................................Pag. 7
3.2 Dimensions....................................................................................................................................................... Pag. 7
3.3 Unit’s main components ..................................................................................................................................Pag. 8
3.4 Back panel description .....................................................................................................................................Pag. 9
4. Installation .............................................................................................................................................................Pag. 10
4.1 Mechanical installation ................................................................................................................................... Pag. 11
4.2 Safety chain .....................................................................................................................................................Pag. 11
4.3 Adjusting unit’s tilt ...........................................................................................................................................Pag. 11
4.4 Optic group, framing system and gobos.......................................................................................................Pag. 11
5. Powering up ............................................................................................................................................................Pag. 13
5.1 Operating voltage and frequency ................................................................................................................. Pag. 13
5.2 Connection to mains power ..........................................................................................................................Pag. 13
6. Control signal connections ..................................................................................................................................Pag. 14
6.1 Control signal connection by XLR5 plugs ................................................................................................... Pag. 14
7. Turning the projector on ........................................................................................................................................Pag. 15
7.1 DMX address of the unit ................................................................................................................................ Pag. 15
8. DMX Chart............................................................................................................................................................ Pag. 16
8.1 DMX Chart 16, 7, 1 channels ......................................................................................................................... Pag. 16
8.2 DMX Chart Studio mode .............................................................................................................................. Pag. 18
8.3 DMX Chart RGB mode ............................................................................................................................... Pag. 20
9. Display panel functions ...................................................................................................................................... Pag. 21
9.1 Quick guide to menu ...................................................................................................................................... Pag. 21
9.2 Rapid count .....................................................................................................................................................Pag. 21
9.3 Main functions menu .................................................................................................................................... Pag. 22
9.4 Measure (MEAS) ......................................................................................................................................... Pag. 25
9.5 Electronic alignment of the LEDs ............................................................................................................... Pag. 26
9.6 Special functions of the fixture .................................................................................................................... Pag. 28
9.7 Error messages ............................................................................................................................................. Pag. 28
10. Spare parts .......................................................................................................................................................... Pag. 29

4
11. Maintenance ....................................................................................................................................................... Pag. 29
11.1 Firmware update ........................................................................................................................................... Pag. 29
11.2 Periodic cleaning .......................................................................................................................................... Pag. 29
11.3 Periodic controls .......................................................................................................................................... Pag. 29
11.4 Fuses ..............................................................................................................................................................Pag. 29
12. F.A.Q. and answers ............................................................................................................................................. Pag. 30

5
Congratulations on having purchased a Coemar product. You have assured yourself of a fixture of the highest
quality, both in componentry and in the technology used. We renew our invitation to you to complete the service
information on the previous page, to expedite any request for service information or spares (in case of problems
encountered either during, or subsequent to, installation). This information will assist in providing prompt and ac-
curate advice from your Coemar service centre. Following the instructions and procedures outlined in this manual
will ensure the maximum eciency of this product for years to come.
1. Packaging and transportation
1.1 Packaging
Open the packaging and make sure that no part of the equipment has suered any damage during the transpor-
tation. In case of damage to the fixture, contact your currier and your supplier immediately by telephone, fax or
e-mail, and inform them you will formally notify them in writing through registered letter.
Packing list
Ensure the packaging contains:
1 LEDko EXT FullSpectrum RGBLA
1 Instruction manual
2. General information
1.2 Transportation
Fire prevention:
1. Never locate the fixture on any flammable surface.
2. Minimum distance from flammable materials: 0,5 m.
3. Minimum distance from the closet illuminable surface: 0,5 m.
4. Replace any blown or damaged fuse only with those of identical values. Refer to the sche-
matic diagram if there is any doubt.
5. Connect the projector to mains power protected by a thermal magnetic circuit breaker.
Prevention from electric shock:
1. Presence of high voltage inside of the fixture. Insulate the projector from mains supply
before opening or performing any function which involves touching the inside of the fix-
ture, including lamp replacement.
2. For the connection to the mains, adhere strictly to the guidelines outlined in this manual.
1.2 Transportation
The LEDko EXT FullSpectrum RGBLA should be transported in either its original packaging or in an appropri-
ate flight case.

6
Safety:
1. The projector must always be installed with bolts, clamps, or other fixing devices which are
suitably rated to support the weight of the projector.
2. Always use a secondary safety fixing device with chain or steel wire of a suitable rating to
sustain the weight of the unit in case of failure of the principal fixing point.
3. The external surfaces of the unit, at various points, may reach 60°C. Never handle the
unit until at least 10 minutes have elapsed since the LED was turned o.
4. Never install the fixture in an enclosed area lacking sucient air flow; the room tempera-
ture must not exceed 35°C.
5. The projector contains electronic and electrical components which must under no cir-
cumstances be in contact with water, oil or any other liquid. Failure to do so will compro-
mise the proper functioning of the projector.
2.2 Warranty conditions
1. The fixture is under warranty for 36 months from the purchase date against factory defections.
2. Damage ought to unskillfulness, inappropriate use, or lack of suggested maintenance are excluded from the
warranty.
3. Warranty expires when the projector is opened by unauthorized personnel.
4. Warranty doesn’t include the replacement of the fixture.
5. Serial number and model of the fixture are necessary to retrieve informations and assistance from the
dealer.
2.3 EC Norms
The projector meets all fundamental applicable EC requirements.
3. The level of technology of LEDko EXT FullSpectrum RGBLA requires the use of spe-
cialised personnel for all service applications; refer all work to your authorised Coemar
service centre.
4. A good earth connection is essential for the proper functioning of the projector. Never
connect the fixture if there is no earth connection.
5. Mains cables must not come into contact with other cables.
6. Do not operate the projector with wet hands or in an area where water is present.
7. The fixture must never be located in an exposed position, or in areas of extreme humidity.

7
3. Product specifications
3.1 Technical characteristics
3.2 Dimensions
=
ø 75 mm
Gobo Holder
Power supply 80-264 V, auto-sensing, 50/60 Hz
Maximum current 1.16 A at 230 V, 2.34 A at 115 V
Power factor Cosφ= 0.93
Max power consumption 250 W
Color temperature RGBLA color mixing and all whites from 2.700 to 6.500 K
Weight 14.0 Kg (30.8 lbs)
Storage temperature from - 40° C / -40° F to + 85° C / +185° F
Operating temperature from - 40° C / -40° F to + 40° C / +104° F
IP rating 65
687.8 mm
27.07 in
252.6 mm
9.94 in
405 mm
15.94 in
252.6 mm
9.94 in

8
3.3 Unit’s main components
A
B
C
D
Components description
AYoke with mounting holes
BCooling unit
COptical holder tube
DLocking screw for yoke

9
3.4 Back panel description
Plus button
Minus button
DMX Out
DMX In
Display
Menu button
Enter button
Power In

10
4. Installation
4.1 Mechanical installation
LEDko EXT FullSpectrum RGBLA may be hung from an appropriate structure in any position or on tripod.
If hanging the fixture from a lighting truss or similar, we recommend the use of an appropriate clamp “A”, as
shown in the following diagram.
Warning!!
Always ensure that your support structure
and fixing (bolts, clamps, etc…) are rated
to support the weight of the fixture.
4.2 Safety chain
When hanging LEDko EXT FullSpectrum RGBLA it is recommended to use a safety chain, as required by cur-
rent legislation. The safety chain must pass through the handles of the unit and then attached to the structure.
If using steel cables and chains not Coemar’s production, make sure they are suitable to support the weight of
the unit according to normative UL/ETL (required: the weight of 6 complete devices for at least one hour).

11
4.4 Optical group and framing system
Follow these steps in order to configure the optical group properly:
1. Remove the two screws “C” placed on both sides of the optical holder tube;
2. Gently remove the optical holder tube “D” pulling it away from the body;
3. Loose the thumbscrews “E” of the two lenses to set them at desired position. Turn on the fixture and check
if the desired focus and zoom lever are correct, then tighten the thumbscrews;
4.3 Adjusting unit’s tilt
1. In order to adjust the tilt of the unit simply loose the side screw “B” on the yoke, adjust the tilt and lock the
yoke by tightening the screw again.
C
D
E
B

12
4. It is possible to regulate the blades “D” to achieve the desired shape, use the four thumbscrews “E” that you
can see behind the blades to free or block them;
5. It is possible to use the gobos, to do so open the gobo holder, insert a normal gobo or a glass gobo and close
the gobo holder;
7. Reassemble the projector by pushing the optical holder tube on the optical group and tighten the screws
that has been removed at the beginning.
NB: When putting the screws, be careful not to tighten too much, otherwise it may deform the base of the
optical holder tube.
6. Use the hole that you can see above and under the projector to lock the optical group’s position, tighten the
two screws symmetrically with each other in order to keep straight your optical group;
D
E

13
5. Powering up
5.2 Connection to mains power
Mains cable characteristics
The mains cable provided is thermally resistant, complying to the most recent International standards.
Note: in case of cable replacement, similar cable with comparable thermal resistant qualities must be used ex-
clusively (cable 3 X 1,5 ø external 10 mm, rated 300/500 V, tested to 2 KV, operating temperature -40°C +
180°C, Coemar cod. CV5311).
Connection to mains power
LEDko EXT FullSpectrum RGBLA is equipped with an internal cable without power plug.
The max absorption of LEDko EXT FullSpectrum RGBLA is reported in the following table:
- 230 V, 1.16 A constant during normal exercise.
- 115 V, 2.34 A constant during normal exercise.
5.1 Operating voltage and frequency
The unit may operates at voltages ranges from 80 to 264 V at a frequency of 50 or 60 Hz. It is not needed to
eect any setup procedures: LEDko EXT FullSpectrum RGBLA will automatically adjust its operation to suit
any frequency or voltage within this range.
fase
neutral
mass
brown
blue
yellow/green

14
Warning!!
The use of a thermal/magnetic circuit breaker is recommended. Strict adherence to regulatory norms is
strongly recommended.
LEDko EXT FullSpectrum RGBLA should not be powered through a dimmer as this may damage the
internal switching power supply.
Prior to connecting the device to mains power, ensure that the mains characteristics are within the rec-
ommended range for the use of LEDko EXT FullSpectrum RGBLA.
All cabling and connections should be carried out by a suitably qualified personnel.
Warning!
Make sure that screening and conductors are not in contact one another or with the metal housing of the
connector. Pin#1 and housing never must be connected to the power supply unit.
6.1 Control signal connection by XLR5 plugs
The digital control signal is transmitted to the projector via a two pole cable screened as per International stan-
dards for the transmission of DMX 512 data. The connection must be serial, using connectors XLR5 male and
female located on the back of LEDko EXT FullSpectrum RGBLA labelled DMX512 IN e OUT (see diagram).
Connectors equipped on LEDko EXT FullSpectrum RGBLA are IP rated, which ensures protection against
water and dust. In order to keep this rating they must be connected exclusively to other IP rated connectors.
6. Control signal connections
DMX IN DMX OUT

15
A00 1
7. Turning the projector on
After having followed the preceding steps described, proceed with the power supply and turn on the projector
connecting it to the mains power.
The software version installed on the internal microprocessors will be shown on the display, suddenly it will show
the current DMX addressing. If the address blinks, it means that the DMX signal has not been received. Check
the connection cable and the mixer functioning.
7.1 DMX address of the unit
Each projector can use 16, 7, 1 address channels + Studio and RGB mode for its complete operation and is
controlled by a DMX 512 signal.
DMX addressing
When powered up initially, each projector will show A001, which indicates DMX address 001; for example,
when set at 16 channels a projector thus addressed will respond to commands of channel 1 to 16 from your DMX
512 controller. A second unit must be addressed as A017, a third one as A033 and so on. The operation must be
carried out on every LEDko EXT FullSpectrum RGBLA which has an address dierent from A001.
Altering the DMX address:
1. Press the + or – button until the display shows the required DMX address. The digits on the display will blink
to indicate that the variation has not been registered.
2. Press the enter key to confirm your selection. The digits on the display panel will cease to blink and the
projector will now respond to the new address.
Note: by holding the + or – button down the scrolling will be faster; thus allowing a faster selection
Warning!
If you alter the DMX address with no DMX signal connected, the digits on the display
panel will continue to flash even after you have pressed ENTER button to confirm the
address.

16
8. DMX chart
8.1 DMX Chart 16, 7, 1 channels
channel function type of control eect decimal percentage
16 7 1
1 1 12master dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2 2 - red proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
3 3 - green proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
4 4 - blue proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
5 5 - spare channel step no eect 0 - 255 0% - 100%
6 6 - lime proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
7 7 - amber proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
8 - - strobe
step no eect 0 - 9 0% - 4%
proportional pulse eect 10 -57 4% - 22%
step no eect 58 - 255 23% - 100%
9 - - dimmer fine proportional fine dimmer control 16 bit 0 - 255 0% - 100%
10 - - special functions step
no eect 0 - 71 0% - 28%
600 Hz 72 - 84 28% - 33%
fan at auto-silent speed 85 - 133 33% - 52%
enables the automatic display blackout 134 - 185 53% - 73%
disables the automatic display blackout 186 - 199 73% - 78%
LED control frequency tuning 1.000 Hz 200 - 205 78% - 80%
LED control frequency tuning 3.000 Hz 206 - 211 81% - 83%
LED control frequency tuning 6.000 Hz 212 - 217 83% - 85%
LED control frequency tuning 8.000 Hz 218 - 223 85% - 87%
LED control frequency tuning 10.000 Hz 224 - 229 88% - 90%
LED control frequency tuning 12.000 Hz 230 - 235 90% - 92%
LED control frequency tuning 14.000 Hz 236 - 241 93% - 95%
LED control frequency tuning 16.000 Hz 242 -247 95% - 97%
LED control frequency tuning 19.000 Hz 248 - 255 97% - 100%
111- - red tone step
no eect 0 - 9 0% - 4%
R24 - Scarlet red 10 - 34 4% - 13%
R02 - Bastard amber 35 - 59 14% - 23%
R313 - Light relief yellow 60 - 84 24% - 33%
R18 - Flame 85 - 109 33% - 43%
R331 - Shell pink 110 - 134 43% - 53%
R25 - Orange red 135 - 159 53% - 62%
R46 - Magenta 160 - 184 63% - 72%
R08 - Pale gold 185 - 209 73% - 82%
R27 - Medium red 210 - 234 82% - 92%
R318 - Mayan sun 235 - 255 92% - 100%

17
121- - green tone step
no eect 0 - 9 0% - 4%
R4460 - Calcolor 60 green 10 - 34 4% - 13%
R2004 - Storaro green 35 - 59 14% - 23%
E730 - Liberty green 60 - 84 24% - 33%
E088 - Lime green 85 - 109 33% - 43%
R90 - Kelly green 110 - 134 43% - 53%
R395 - Teal green 135 - 159 53% - 62%
R91 - Primary green 160 - 184 63% - 72%
R393 - Emerald green 185 - 209 73% - 82%
R393 - Leaf green 210 - 234 82% - 92%
R86 - Pea green 235 - 255 92% - 100%
131- - blue tone step
no eect 0 - 9 0% - 4%
R2008 - Storaro indigo 10 - 34 4% - 13%
E5058 - French lilac 35 - 59 14% - 23%
R369 - Tahitian blue 60 - 84 24% - 33%
R347 - Belladonna rose 85 - 109 33% - 43%
R381 - Baldassari blue 110 - 134 43% - 53%
R57 - Lavander 135 - 159 53% - 62%
R55 - Lilac 160 - 184 63% - 72%
R4790 - Calcolor 90 magenta 185 - 209 73% - 82%
R92 - Turquise 210 - 234 82% - 92%
R370 - Italian blue 235 - 255 92% - 100%
14 - - white tone
step no eect 0 - 9 0% - 4%
2.700 K 10 - 30 4% - 12%
proportional proportional value from 2.700 K to 3.200 K 31 - 52 12% - 20%
step 3.200 K 53 - 74 21% - 29%
proportional proportional value from 3.200 K to 4.000 K 75 - 96 29% - 38%
step 4.000 K 97 - 118 38% - 46%
proportional proportional value from 4.000 K to 5.000 K 119 - 140 47% - 55%
step 5.000 K 141 - 162 55% - 64%
proportional proportional value from 5.000 K to 5.600 K 163 - 184 64% - 72%
step 5.600 K 185 - 206 73% - 81%
proportional proportional value from 5.600 K to 6.500 K 207 - 228 81% - 89%
step 6.500 K 229 - 255 90% - 100%
152- - green saturation
step no eect 0 0%
proportional exalts the green color in the mixing and diminishes the
presence of magenta 1 - 127 0% - 50%
step no eect 128 50%
proportional diminishes the presence of green in the mixing and
exalts the green color 129 - 254 51% - 99%
step no eect 255 100%
163- - saturation proportional the white tone fades to the tone built with the
RGBLA channels 0 - 255 0% - 100%
Note 1: colors macros of channels 11-12-13 can also be obtained through the mixing of channels 2-3-4-6-7.
Note 2: the rest position of green saturation is 128. Diminishing the DMX value augments the presence of the green color.
Increasing the DMX value augments the presence of magenta.
Note 3: increasing the value of the saturation DMX channel the white tone (channel 14) will fade to the color selected by the
channel 2-3-4-6-7.

18
8.2 DMX Chart Studio mode
channel function type of control eect decimal percentage
1master dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2white tone step
3.200 K 0 - 10 0% - 4%
2.700 K 11 - 16 4% - 6%
2.800 K 17 - 22 7% - 9%
2.900 K 23 - 28 9% - 11%
3.000 K 29 - 34 11% - 13%
3.100 K 35 - 40 14% - 16%
3.200 K 41 - 46 16% - 18%
3.300 K 47 -52 18% - 20%
3.400 K 53 - 58 21% - 23%
3.500 K 59 - 64 23% - 25%
3.600 K 65 - 70 25% - 27%
3.700 K 71 - 76 28% - 30%
3.800 K 77 - 82 30% - 32%
3.900 K 83 - 88 33% - 35%
4.000 K 89 - 94 35% - 37%
4.100 K 95 - 100 37% - 39%
4.200 K 101 -106 40% - 42%
4.300 K 107 - 112 42% - 44%
4.400 K 113 - 118 44% - 46%
4.500 K 119 - 124 47% -49%
4.600 K 125 - 130 49% -51%
4.700 K 131 - 136 51% - 53%
4.800 K 137 - 142 54% - 56%
4.900 K 143 - 148 56% - 58%
5.000 K 149 - 154 58% - 60%
5.100 K 155 - 160 61% - 63%
5.200 K 161 - 166 63% - 65%
5.300 K 167 - 172 65% - 67%
5.400 K 173 - 178 68% - 70%
5.500 K 179 - 184 70% - 72%
5.600 K 185 - 190 73% - 75%
5.700 K 191 - 196 75% - 77%
5.800 K 197 -202 77% - 79%
5.900 K 203 - 208 80% - 82%
6.000 K 209 - 214 82% - 84%
6.100 K 215 - 220 84% - 86%
6.200 K 221 - 226 87% - 89%
6.300 K 227 - 232 89% - 91%
6.400 K 233 - 238 91% - 93%
6.500 K 239 - 244 94% - 96%
5.600 K 245 - 255 96% - 100%
31green saturation
step no eect 0 0%
proportional exalts the green color in the mixing and diminishes the
presence of magenta 1 - 127 0% - 20%
step no eect 128 50%
proportional diminishes the presence of green in the mixing and
exalts the green color 129 - 254 51% - 99%
step no eect 255 100%
42saturation proportional the white tone fades to the tone built with the hue
channel 0 - 255 0% - 100%

19
5hue proportional reproduce the color crossfades around the color space 0 - 255 0% - 100%
6dimmer fine proportional fine dimmer control 16 bit 0 - 255 0% - 100%
7special functions step
no eect 0 - 71 0% - 28%
600 Hz 72 - 84 28% - 33%
fan at auto-silent speed 85 - 133 33% - 52%
enables the automatic display blackout 134 - 185 53% - 73%
disables the automatic display blackout 186 - 199 73% - 78%
LED control frequency tuning 1.000 Hz 200 - 205 78% - 80%
LED control frequency tuning 3.000 Hz 206 - 211 81% - 83%
LED control frequency tuning 6.000 Hz 212 - 217 83% - 85%
LED control frequency tuning 8.000 Hz 218 - 223 85% - 87%
LED control frequency tuning 10.000 Hz 224 - 229 88% - 90%
LED control frequency tuning 12.000 Hz 230 - 235 90% - 92%
LED control frequency tuning 14.000 Hz 236 - 241 93% - 95%
LED control frequency tuning 16.000 Hz 242 -247 95% - 97%
LED control frequency tuning 19.000 Hz 248 - 255 97% - 100%
Note 1: the rest position of green saturation is 128. Diminishing the DMX value augments the presence of the green color. Increasing
the DMX value augments the presence of magenta.
Note 2: Increasing the value of the saturation DMX channel (channel 4) the white light will fade to the color selected with the hue
channel (channel 5)

20
channel function type of control eect decimal percentage
1master dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2dimmer fine proportional fine dimmer control 16 bit 0 - 255 0% - 100%
3red proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
4green proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
5blue proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
6white tone
step no eect 0 - 9 0% - 4%
2.700 K 10 - 30 4% - 12%
proportional proportional value from 2.700 K to 3.200 K 31 - 52 12% - 20%
step 3.200 K 53 - 74 21% - 29%
proportional proportional value from 3.200 K to 4.000 K 75 - 96 29% - 38%
step 4.000 K 97 - 118 38% - 46%
proportional proportional value from 4.000 K to 5.000 K 119 - 140 47% - 55%
step 5.000 K 141 - 162 55% - 64%
proportional proportional value from 5.000 K to 5.600 K 163 - 184 64% - 72%
step 5.600 K 185 - 206 73% - 81%
proportional proportional value from 5.600 K to 6.500 K 207 - 228 81% - 89%
step 6.500 K 229 - 255 90% - 100%
7saturation proportional the white tone fades to the tone built with the hue
channel 0 - 255 0% - 100%
8strobe eect
step no eect 0 - 9 0% - 4%
proportional pulse eect 10 -57 4% - 22%
step no eect 58 - 255 23% - 100%
8.3 DMX Chart RGB mode
9special function step
no eect 0 - 71 0% - 28%
600 Hz 72 - 84 28% - 33%
fan at auto-silent speed 85 - 133 33% - 52%
enables the automatic display blackout 134 - 185 53% - 73%
disables the automatic display blackout 186 - 199 73% - 78%
LED control frequency tuning 1.000 Hz 200 - 205 78% - 80%
LED control frequency tuning 3.000 Hz 206 - 211 81% - 83%
LED control frequency tuning 6.000 Hz 212 - 217 83% - 85%
LED control frequency tuning 8.000 Hz 218 - 223 85% - 87%
LED control frequency tuning 10.000 Hz 224 - 229 88% - 90%
LED control frequency tuning 12.000 Hz 230 - 235 90% - 92%
LED control frequency tuning 14.000 Hz 236 - 241 93% - 95%
LED control frequency tuning 16.000 Hz 242 -247 95% - 97%
LED control frequency tuning 19.000 Hz 248 - 255 97% - 100%