Coemar Reflection LEDko FullSpectrum 6 User manual

Version 2.0
FullSpectrum 6
instruction manual

2
Please note in the space provided above the relative service information of the model and the
retailer from whom you purchased your LEDko FullSpectrum 6: this information will assist us in
providing spare parts, repairs or in answering any technical enquiries with the utmost speed and
accuracy.
WARNING: the security of the fixture is granted only if these instructions are strictly followed;
therefore it is absolutely necessary to keep this manual.
User Manual version 2.0
Edition April 2018
Serial Number:
...............................................................................................................................................................................................
Purchase date:
...............................................................................................................................................................................................
Dealer:
...............................................................................................................................................................................................
Address:
...............................................................................................................................................................................................
Suburb:
...............................................................................................................................................................................................
Country:
...............................................................................................................................................................................................
Phone / Fax:
...............................................................................................................................................................................................
FullSpectrum 6

3
Index
1. Packaging and transportation..............................................................................................................Pag. 5
1.1. Packaging...........................................................................................................................................................Pag. 5
1.2. Transportation..................................................................................................................................................Pag. 5
2. General information.......................................................................................................................................Pag. 5
2.1 Safety informations...........................................................................................................................................Pag. 5
2.2 Warranty conditions.......................................................................................................................................Pag. 6
2.3 EC Norms ............................................................................................................................................................Pag. 6
3. Product specifications................................................................................................................................. Pag. 7
3.1 Technical characteristics................................................................................................................................Pag. 7
3.2 Dimensions..........................................................................................................................................................Pag. 7
3.3 Unit’s main components...............................................................................................................................Pag. 8
3.4 Back panel description...................................................................................................................................Pag. 9
4. Installation.......................................................................................................................................................... Pag. 10
4.1 Optical Installation........................................................................................................................................ Pag. 10
4.2 Mechanical installation............................................................................................................................... Pag. 11
4.3 Safety chain...................................................................................................................................................... Pag. 11
4.4 Adjusting unit’s tilt......................................................................................................................................... Pag. 11
5. Powering up....................................................................................................................................................... Pag. 12
5.1 Operating voltage and frequency ........................................................................................................ Pag. 12
5.2 Connection to mains power.................................................................................................................... Pag. 12
6. Control signal connections................................................................................................................... Pag. 14
6.1 Control signal connection by XLR5 plugs ......................................................................................... Pag. 14
7. Turning on the projector......................................................................................................................... Pag. 15
7.1 DMX address of the unit ........................................................................................................................... Pag. 15
8. DMX Chart (software vrs. 1.09 - 1.23) ......................................................................................... Pag. 16
8.1 DMX Chart 16, 9, 6, 1 channels ............................................................................................................. Pag. 16
8.2 DMX Chart 5 channels ............................................................................................................................... Pag. 18
9. DMX Chart (software vrs. 1.31 - 2.03) ......................................................................................... Pag. 19
9.1 DMX Chart 16, 10, 6, 1 channels .......................................................................................................... Pag. 19
9.2 DMX Chart 5 channels ............................................................................................................................... Pag. 20
10. DMX Chart (software vrs. 2.04 or following) .................................................................... Pag. 23
10.1 DMX Chart 16, 7, 1 channels ............................................................................................................... Pag. 23
10.2 DMX Chart 5 channels ........................................................................................................................... Pag. 24

4
11. Display panel functions........................................................................................................................ Pag. 26
11.1 Quick guide to menu............................................................................................................................... Pag. 26
11.2 Rapid count.................................................................................................................................................. Pag. 26
11.3 Main functions menu............................................................................................................................... Pag. 27
11.4 Measure (MEAS)......................................................................................................................................... Pag. 29
11.5 Electronic alignment of the LEDs........................................................................................................ Pag. 31
11.6 Special functions of the fixture............................................................................................................. Pag. 32
11.7 Error messages............................................................................................................................................ Pag. 32
12. Accessories and spare parts.............................................................................................................. Pag. 33
13. Maintenance................................................................................................................................................... Pag. 35
13.1 Firmware update....................................................................................................................................... Pag. 35
13.2 Periodic cleaning....................................................................................................................................... Pag. 35
13.3 Periodic controls......................................................................................................................................... Pag. 35
13.4 Fuses................................................................................................................................................................ Pag. 35
14. F.A.Q. and answers................................................................................................................................... Pag. 36

5
Congratulations on having purchased a Coemar product. You have assured yourself of a fixture
of the highest quality, both in componentry and in the technology used. We renew our invitation
to you to complete the service information on the previous page, to expedite any request for
service information or spares (in case of problems encountered either during, or subsequent to,
installation). This information will assist in providing prompt and accurate advice from your Coemar
service centre. Following the instructions and procedures outlined in this manual will ensure the
maximum efficiency of this product for years to come.
1. Packaging and transportation
1.1 Packaging
Open the packaging and make sure that no part of the equipment has suffered any damage
during the transportation. In case of damage to the fixture, contact your currier and your supplier
immediately by telephone, fax or email, and inform them you will formally notify them in writing
through registered letter.
Packing list
Ensure the packaging contains:
1 Reflection LEDko FullSpectrum 6
1 Instruction manual
1 Main power plugs
2. General information
2.1 Safety informations
Fire prevention:
1. Never locate the fixture on any flammable surface.
2. Minimum distance from flammable materials: 0,5m.
3. Minimum distance from the closet illuminable surface: 0,5m.
4. Replace any blown or damaged fuse only with those of identical values. Refer
to the schematic diagram if there is any doubt.
5. Connect the projector to mains power protected by a thermal magnetic
circuit breaker.
Prevention from electric shock:
1. Presence of high voltage inside of the fixture. Insulate the projector from mains
supply before opening or performing any function which involves touching
the inside of the fixture, including lamp replacement.
2. For the connection to the mains, adhere strictly to the guidelines outlined in
this manual.
1.2 Transportation
The LEDko FullSpectrum 6 should be transported in either its original packaging or in an
appropriate flight case.

6
Safety:
1. The projector must always be installed with bolts, clamps, or other fixing
devices which are suitably rated to support the weight of the projector.
2. Always use a secondary safety fixing device with chain or steel wire of
a suitable rating to sustain the weight of the unit in case of failure of the
principal fixing point.
3. The external surfaces of the unit, at various points, may reach 60°C. Never
handle the unit until at least 10 minutes have elapsed since the LED was
turned off.
4. Never install the fixture in an enclosed area lacking sufficient air flow; the
room temperature must not exceed 35°C.
5. The projector contains electronic and electrical components which must
under no circumstances be in contact with water, oil or any other liquid.
Failure to do so will compromise the proper functioning of the projector.
2.2 Warranty conditions
1. The fixture is under warranty for 36 months from the purchase date against factory defections.
2. Damage ought to unskillfulness, inappropriate use, or lack of suggested maintenance are
excluded from the warranty.
3. Warranty expires when the projector is opened by unauthorized personnel.
4. Warranty doesn’t include the replacement of the fixture.
5. Serial number and model of the fixture are necessary to retrieve informations and assistance
from the dealer.
2.3 EC Norms
The projector meets all fundamental applicable EC requirements.
3. The level of technology of LEDko FullSpectrum 6 requires the use of spe-
cialised personnel for all service applications; refer all work to your authorised
Coemar service centre.
4. A good earth connection is essential for the proper functioning of the projec-
tor. Never connect the fixture if there is no earth connection.
5. Mains cables must not come into contact with other cables.
6. Do not operate the projector with wet hands or in an area where water is
present.
7. The fixture must never be located in an exposed position, or in areas of ex-
treme humidity.

7
Power supply 90-230Vac, 50-60Hz
Maximum current 1.06 A a 230 VaC - 2.71 A a 90 Vac
Power factor Cosϕ= 0.9
Power consumption 220 watt
Color temperature RGBWLA, with pure colour mixing throughout the
field and all whites from 2.700 to 6.500 K
Weight (without optic) 6kg - 13.2lbs
Minimum ambient temperature -20°C / -4°F
Maximum ambient temperature +35°C / +95°F
IP rating IP20
3. Product specifications
3.1 Technical characteristics
3.2 Dimensions
601mm
23.66”
369mm
145.3”
189mm
74.4”
355mm
139.8”
229mm
90.2”

8
3.3. Unit’s main components
Components description
AAdjustable yoke
BIris (optional)
CGobo holder (optional)
DLens adjusting handles
EYoke locking handle
FGel frame locking spring
GProfile blade
HInterchangeable optic
A
B
C
D
EF
G
H

9
3.4 Back panel description
Display
Menu button
Enter button
PowerCon In
PowerCon Out
Plus button
Minus button
DMX In
DMX Out

10
4. Installation
Remove the frontal cap by loosening the upper and lower screws enough to free the cap itself, set
the optic’s flange tilted about 60°. Insert the optic’s flange into the body’s receptacle and turn the
optic 60° until it is firmly assembled to the projector body, free to rotate but not free to detach itself
from the body. Ensure the optic to the body by tightening the two screws previously loosened.
4.1 Optical installation
Warning!!
When the protective cap is removed, never lean the fixture facing down.
The front lens can be seriously damaged.

11
4.2 Mechanical installation
LEDko FullSpectrum 6 may be hung from an appropriate structure in any position or on
tripode. If hanging the fixture from a lighting truss or similar, we recommend the use of an
appropriate clamp “A”, as shown in the following diagram.
Warning!!
Always ensure that your support structure
and fixing (bolts, clamps, etc…) are rated
A to support the weight of the fixture.
A
4.3 Safety chain
When hanging LEDko FullSpectrum 6 it is recommended to use a safety chain, as required
by current legislation. The safety chain must pass through the handles of the unit and then
attached to the structure.
If using steel cables and chains not Coemar’s production, make sure they are suitable to support
the weight of the unit according to normative UL/ETL (required: the weight of 6 complete
devices for at least one hour).
4.4 Adjusting unit’s tilt
In order to adjust the tilt of the unit simply loose the side handle adjust the tilt and lock the yoke
by tightening the handle again.

12
5. Powering up
5.2 Connection to mains power
Mains cable characteristics
The mains cable provided is thermally resistant, complying to the most recent International
standards.
Note: in case of cable replacement, similar cable with comparable thermal resistant qualities
must be used exclusively (cable 3 X 1,5 ø external 10 mm, rated 300/500V, tested to 2 KV,
operating temperature -40°C + 180°C, Coemar cod. CV5311).
Connection to mains power
LEDko FullSpectrum 6 is equipped with two power connectors, one as input and one as
output, which can be used to feed up to 8 (at 230 VAC) or 4 (90 VAC) fixtures.
The max absorption of LEDko FullSpectrum 6 is reported in the following table:
- 230 VaC 1.06 A constant during normal exercise.
- 90 VaC 2.71 A constant during normal exercise.
5.1 Operating voltage and frequency
The unit may operates at voltages ranges from 90 to 250VaC at a frequency of 50 or 60 Hz. It is
not needed to effect any setup procedures: LEDko FullSpectrum 6 will automatically adjust its
operation to suit any frequency or voltage within this range.
Warning!!
•The use of a thermal/magnetic circuit breaker is recommended. Strict adherence to regu-
latory norms is strongly recommended.
•LEDko FullSpectrum 6 should not be powered through a dimmer as this may damage
the internal switching power supply.
•Prior to connecting the device to mains power, ensure that the mains characteristics are
within the recommended range for the use of LEDko FullSpectrum 6.
•All cabling and connections should be carried out by a suitably qualified personnel.

13
Warning!
Make sure that screening and conductors are not in contact one another or with the
metal housing of the connector.
Pin#1 and housing must never be connected to the power supply unit.
6.1 Control signal connection by XLR5 plugs
The digital control signal is transmitted to the projector via a two pole cable screened in ac-
cording to the International standards for DMX 512 data transmission. The connection must be
serial, using connectors XLR5 male and female located on the back of LEDko FullSpectrum 6
labelled DMX512 IN e OUT.
DMX In DMX Out
6. Control signal connections

14
A00 1
7. Turning on the projector
After having followed the preceding steps described, proceed with the power supply and turn on
the projector connecting it to the mains power.
The software version installed on the internal microprocessors will be shown on the display,
suddenly it will show the current DMX addressing. If the address blinks, it means that the DMX
signal has not been received. Check the connection cable and the mixer functioning.
7.1 DMX address of the unit
Each projector can use 14/9/6/5/1 (software vrs. 1.09-1.23), 16/10/6/5/1 (software vrs. 1.31-
2.03) or 16/7/5/1 (software vrs. 2.04 or following) address channels for its complete operation
and is controlled by a DMX 512 signal.
DMX addressing
When powered up initially, each projector will show A001, which indicates DMX address 001;
for example, when set at 16 channels a projector thus addressed will respond to commands of
channel 1 to 16 from your DMX 512 controller. A second unit must be addressed as A017, a
third one as A033 and so on.
The operation must be carried out on every LEDko FullSpectrum 6 which has an address
different from A001.
Altering the DMX address:
1. Press the + or – button until the display shows the required DMX address. The digits on the
display will blink to indicate that the variation has not been registered.
2. Press the enter key to confirm your selection. The digits on the display panel will cease to blink
and the projector will now respond to the new address.
Note: by holding the + or – button down the scrolling will be faster; thus allowing a faster
selection
Warning!!
If you alter the DMX address with no DMX signal connected, the digits on the display
panel will continue to flash even after you have pressed ENTER button to confirm the
address.

15
8. DMX chart (software vrs. 1.09 - 1.23)
8.1 DMX Chart 14, 9, 6, 1 channels
channel function type of
control effect decimal percentage
1 1 - 1 master
dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2 2 1 - red proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
3 3 2 - green proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
4 4 3 - blue proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
5 5 4 - white proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
6 6 5 - lime proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
7 7 6 - amber proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
8 8 - - dimmer
fine proportional fine dimmer control 16 bit 0 - 255 0% - 100%
9 9 - - special
functions
step
park, no effect 0 - 71 0% - 28%
600 Hz 72 - 84 28% - 33%
fan at low-noise speed 85 - 96 33% - 38%
fan at auto-silent speed 97 - 108 38% - 42%
proportional fan speed control from minimum to maximum 109 - 120 43% - 47%
step
no effect 121 - 133 47% - 52%
enables the automatic display blackout 134 - 185 53% - 73%
disables the automatic display blackout 186 - 199 73% - 78%
LED control frequency tuning 1000 Hz 200 - 205 78% - 80%
LED control frequency tuning 3000 Hz 206 - 211 81% - 83%
LED control frequency tuning 6000 Hz 212 - 217 83% - 85%
LED control frequency tuning 8000 Hz 218 - 223 85% - 87%
LED control frequency tuning 10000 Hz 224 - 229 88% - 90%
LED control frequency tuning 12000 Hz 230 - 235 90% - 92%
LED control frequency tuning 14000 Hz 236 - 241 93% - 95%
LED control frequency tuning 16000 Hz 242 - 247 95% - 97%
LED control frequency tuning 19000 Hz 248 - 255 97% - 100%
10 - - - red tone step
no effect 0 - 9 0% - 4%
R823 MEDIUM RED 10 - 70 4% - 27%
R25 ORANGE RED (TUNGSTEN) 71 - 132 28% - 52%
R24 SCARLET LED (D65) 133 - 194 52% - 76%
R0 BASTARD AMBER 195 - 255 76% - 100%

16
11 - - - green tone step
no effect 0 - 9 0% - 4%
R4460 CALCOLOR 60 GREEN 10 - 70 4% - 27%
R2004 DEEP GREEN 71 - 132 28% - 52%
E730 LIGHT GREEN 133 - 194 52% - 76%
E088 LIME GREEN 195 - 255 76% - 100%
12 - - - blue tone step
no effect 0 - 9 0% - 4%
R2008 STORARO PURPLE 10 - 70 4% - 27%
E5058 FRENCH LILAC 71 - 132 28% - 52%
SOFT PURPLE 133 - 194 52% - 76%
RIPE PURPLE 195 - 255 76% - 100%
13 - - - white tone
step no effect 0 - 9 0% - 4%
2700 K 10 - 30 4% - 12%
proportional proportional value from 2700 K to 3200 K 31 - 52 12% - 20%
step 3200 K 53 - 74 21% - 29%
proportional proportional value from 3200 k to 4000 K 75 - 96 29% - 38%
step 4000 K 97 - 118 38% - 46%
proportional proportional value from 4000 K to 5000 K 119 - 140 47% - 55%
step 5000 K 141 - 162 55% - 64%
proportional proportional value from 5000 K to 5600 K 163 - 184 64% - 72%
step 5600 K 185 - 206 73% - 81%
proportional proportional value from 5600 K to 6500 K 207 - 228 81% - 89%
step 6500 K 229 - 255 90% - 100%
14 - - - green
saturation
step no effect 0 - 9 0% - 4%
proportional exalts the green color in the mixing and diminishes the
presence of magenta 10 - 123 4% - 48%
step no effect 124 - 132 49% - 52%
proportional diminishes the presence of green in the mixing and exalts the
magenta color 133 - 246 52% - 96%
step no effect 247 - 255 97% - 100%
NOTE 1: channels involving 10 - 11 - 12 macro colors can also be obtained by mixing channels
2 - 3 - 4 - 5 - 6 - 7.
NOTE 2: one channel function mode selects the CCT through the display function menu.
NOTE 3: the rest position of the green sauration is 128. Diminishing the DMX value augments the presence
of the green color. Increasing the DMX value augments the presence of magenta.

17
8.2 DMX Chart 5 channels
channel function type of
control effect decimal percentage
1master
dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2 white tone
step no effect 0 - 9 0% - 4%
2700 K 10 - 30 4% - 12%
proportional proportional value from 2700 K to 3200 K 31 - 52 12% - 20%
step 3200 K 53 - 74 21% - 29%
proportional proportional value from 3200 K to 4000 K 75 - 96 29% - 38%
step 4000 K 97 - 118 38% - 46%
proportional proportional value from 4000 K to 5000 K 119 - 140 47% - 55%
step 5000 K 141 - 162 55% - 64%
proportional proportional value from 5000 K to 5600 K 163 - 184 64% - 72%
step 5600 K 185 - 206 73% - 81%
proportional proportional value from 5600 K to 6500 K 207 - 228 81% - 89%
step 6500 K 229 - 255 90% - 100%
3green
saturation
step no effect 0 - 9 0% - 4%
proportional exalts the green color in the mixing and diminishes the
presence of magenta 10 - 123 4% - 48%
step no effect 124 - 132 49% - 52%
proportional diminishes the presence of green in the mixing and exalts the
magenta color 133 - 246 52% - 96%
step no effect 247 - 255 97% - 100%
4dimmer
fine proportional fine dimmer control 16 bit 0 - 255 0% - 100%
5special
functions
step
park, no effect 0 - 71 0% - 28%
600 Hz 72 - 84 28% - 33%
fan at low-noise speed 85 - 96 33% - 38%
fan at auto-silent speed 97 - 108 38% - 42%
proportional fan speed control from minimum to maximum 109 - 120 43% - 47%
step
no effect 121 - 133 47% - 52%
enables the automatic display blackout 134 - 185 53% - 73%
disables the automatic display blackout 186 - 199 73% - 78%
LED control frequency tuning 1000 Hz 200 - 205 78% - 80%
LED control frequency tuning 3000 Hz 206 - 211 81% - 83%
LED control frequency tuning 6000 Hz 212 - 217 83% - 85%
LED control frequency tuning 8000 Hz 218 - 223 85% - 87%
LED control frequency tuning 10000 Hz 224 - 229 88% - 90%
LED control frequency tuning 12000 Hz 230 - 235 90% - 92%
LED control frequency tuning 14000 Hz 236 - 241 93% - 95%
LED control frequency tuning 16000 Hz 242 - 247 95% - 97%
LED control frequency tuning 19000 Hz 248 - 255 97% - 100%
NOTE 1: the rest position of green saturation is 128. Diminishing the DMX value augments the presence of the
green color. Increasing the DMX value augments the presence of magenta.

18
9. DMX chart (software vrs. 1.31 - 2.03)
9.1 DMX Chart 16, 10, 6, 1 channels
channel function type of
control effect decimal percentage
1 1 - 1 master
dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2 2 1 - red proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
3 3 2 - green proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
4 4 3 - blue proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
5 5 4 - white proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
6 6 5 - lime proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
7 7 6 - amber proportional proportional control of the color percentage from 0 to 100% 0 - 255 0% - 100%
8 8 - - strobe
effect
step no effect 0 - 9 0% - 4%
proportional variable speed strobing effect, from slow to fast 10 - 57 4% - 22%
step stop strobe 58 - 59 23% - 23%
proportional sequenced pulsed strobe, slow closing, fast operating
(variable speed pulsing, from slow to fast) 60 - 108 24% - 42%
step stop strobe 109 - 110 43% - 43%
proportional sequenced pulsed strobe, fast closing, slow operating
(variable speed pulsing, from slow to fast) 111 - 159 44% - 62%
step stop strobe 160 - 161 63% - 63%
proportional random strobe effect with variable speed from slow to fast
and synchronized colors 162 - 207 64% - 81%
step stop strobe 208 - 209 82% - 82%
proportional random strobe effect with variable speed from slow to fast
and non-synchonized colors 210 - 255 82% - 100%
9 9 - - dimmer
fine proportional fine dimmer control 16 bit 0 - 255 0% - 100%

19
10 10 - - special
functions
step
park, no effect 0 - 71 0% - 28%
600 Hz 72 - 84 28% - 33%
fan at low-noise speed 85 - 96 33% - 38%
fan at auto-silent speed 97 - 108 38% - 42%
proportional fan speed control from minimum to maximum 109 - 120 43% - 47%
step
no effect 121 - 133 47% - 52%
enables the automatic display blackout 134 - 185 53% - 73%
disables the automatic display blackout 186 - 199 73% - 78%
LED control frequency tuning 1000 Hz 200 - 205 78% - 80%
LED control frequency tuning 3000 Hz 206 - 211 81% - 83%
LED control frequency tuning 6000 Hz 212 - 217 83% - 85%
LED control frequency tuning 8000 Hz 218 - 223 85% - 87%
LED control frequency tuning 10000 Hz 224 - 229 88% - 90%
LED control frequency tuning 12000 Hz 230 - 235 90% - 92%
LED control frequency tuning 14000 Hz 236 - 241 93% - 95%
LED control frequency tuning 16000 Hz 242 - 247 95% - 97%
LED control frequency tuning 19000 Hz 248 - 255 97% - 100%
11 - - - red tone step
no effect 0 - 9 0% - 4%
R823 MEDIUM RED 10 - 70 4% - 27%
R25 ORANGE RED (TUNGSTEN) 71 - 132 28% - 52%
R24 SCARLET LED (D65) 133 - 194 52% - 76%
R0 BASTARD AMBER 195 - 255 76% - 100%
12 - - - green tone step
no effect 0 - 9 0% - 4%
R4460 CALCOLOR 60 GREEN 10 - 70 4% - 27%
R2004 DEEP GREEN 71 - 132 28% - 52%
E730 LIGHT GREEN 133 - 194 52% - 76%
E088 LIME GREEN 195 - 255 76% - 100%
13 - - - blue tone step
no effect 0 - 9 0% - 4%
R2008 STORARO PURPLE 10 - 70 4% - 27%
E5058 FRENCH LILAC 71 - 132 28% - 52%
SOFT PURPLE 133 - 194 52% - 76%
RIPE PURPLE 195 - 255 76% - 100%
14 - - - white tone
step no effect 0 - 9 0% - 4%
2700 K 10 - 30 4% - 12%
proportional proportional value from 2700 K to 3200 K 31 - 52 12% - 20%
step 3200 K 53 - 74 21% - 29%
proportional proportional value from 3200 k to 4000 K 75 - 96 29% - 38%
step 4000 K 97 - 118 38% - 46%
proportional proportional value from 4000 K to 5000 K 119 - 140 47% - 55%
step 5000 K 141 - 162 55% - 64%
proportional proportional value from 5000 K to 5600 K 163 - 184 64% - 72%
step 5600 K 185 - 206 73% - 81%
proportional proportional value from 5600 K to 6500 K 207 - 228 81% - 89%
step 6500 K 229 - 255 90% - 100%
15 - - - green
saturation
step no effect 0 - 9 0% - 4%
proportional exalts the green color in the mixing and diminishes the
presence of magenta 10 - 123 4% - 48%
step no effect 124 - 132 49% - 52%
proportional diminishes the presence of green in the mixing and exalts the
magenta color 133 - 246 52% - 96%
step no effect 247 - 255 97% - 100%
16 - - - saturation proportional the white tone fades to the tone built with
RGBWLA channels 0 - 255 0% - 100%
NOTE 1: channels involving 10 - 11 - 12 macro colors can also be obtained by mixing channels 2 - 3 - 4 - 5 - 6 - 7.
NOTE 2: one channel function mode selects the CCT through the display function menu.
NOTE 3: the rest position of the green sauration is 128. Diminishing the DMX value augments the presence of
the green color. Increasing the DMX value augments the presence of magenta.

20
9.2 DMX Chart 5 channels
channel function type of
control effect decimal percentage
1master
dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2white
temperature step
3200 K 0 - 5 0% - 2%
2700 K 6 - 11 2% - 4%
2800 K 12 - 17 5% - 7%
2900 K 18 - 23 7% - 9%
3000 K 24 - 29 9% - 11%
3100 K 30 - 35 12% - 14%
3200 K 36 - 41 14% - 16%
3300 K 42 - 47 16% - 18%
3400 K 48 - 53 19% - 21%
3500 K 54 - 59 21% - 23%
3600 K 60 - 65 24% - 25%
3700 K 66 - 71 26% - 28%
3800 K 72 - 77 28% - 30%
3900 K 78 - 83 31% - 33%
4000 K 84 - 89 33% - 35%
4100 K 90 - 95 35% - 37%
4200 K 96 - 101 38% - 40%
4300 K 102 - 107 40% - 42%
4400 K 108 - 113 42% - 44%
4500 K 114 - 119 45% - 47%
4600 K 120 - 125 47% - 49%
4700 K 126 - 131 49% - 51%
4800 K 132 - 137 52% - 54%
4900 K 138 - 143 54% - 56%
5000 K 144 - 149 56% - 58%
5100 K 150 - 155 59% - 61%
5200 K 156 - 161 61% - 63%
5300 K 162 - 167 64% - 65%
5400 K 168 - 173 66% - 68%
5500 K 174 - 179 68% - 70%
5600 K 180 - 185 71% - 73%
5700 K 186 - 191 73% - 75%
5800 K 192 - 197 75% - 77%
5900 K 198 - 203 78% - 80%
6000 K 204 - 209 80% - 82%
6100 K 210 - 215 82% - 84%
6200 K 216 - 221 85% - 87%
6300 K 222 - 227 87% - 89%
6400 K 228 - 233 89% - 91%
6500 K 234 - 239 92% - 94%
5600 K 240 - 255 94% - 100%