Coemar LEDko FullSpectrum Series 2 User manual

FullSpectrum Series 2

2
Please note in the space provided above the relative service information of the model and the
retailer from whom you purchased your LEDko FullSpectrum Series 2: this information will
assist us in providing spare parts, repairs or in answering any technical enquiries with the utmost
speed and accuracy.
WARNING: the security of the fixture is granted only if these instructions are strictly followed;
therefore it is absolutely necessary to keep this manual.
User Manual version 2.0
Edition June 2018
Serial Number:
......................................................................................................................................................................
Purchase date:
......................................................................................................................................................................
Dealer:
......................................................................................................................................................................
Address:
......................................................................................................................................................................
Suburb:
......................................................................................................................................................................
Country:
......................................................................................................................................................................
Phone / Fax:
......................................................................................................................................................................
FullSpectrum Series 2

3
Index
1. Packaging and transportation..............................................................................................................Pag. 5
1.1. Packaging...........................................................................................................................................................Pag. 5
1.2. Transportation..................................................................................................................................................Pag. 5
2. General information.......................................................................................................................................Pag. 5
2.1 Safety informations...........................................................................................................................................Pag. 5
2.2 Warranty conditions.......................................................................................................................................Pag. 6
2.3 EC Norms.............................................................................................................................................................Pag. 6
3. Product specifications................................................................................................................................. Pag. 7
3.1 Technical characteristics................................................................................................................................Pag. 7
3.2 Dimensions..........................................................................................................................................................Pag. 7
3.3 Unit’s main components...............................................................................................................................Pag. 8
3.4 Back panel description...................................................................................................................................Pag. 9
4. Installation.......................................................................................................................................................... Pag. 10
4.1 Optical Installation........................................................................................................................................ Pag. 10
4.2 Mechanical installation............................................................................................................................... Pag. 11
4.3 Safety chain...................................................................................................................................................... Pag. 11
4.4 Adjusting unit’s tilt......................................................................................................................................... Pag. 11
5. Powering up....................................................................................................................................................... Pag. 12
5.1 Operating voltage and frequency ........................................................................................................ Pag. 12
5.2 Connection to mains power.................................................................................................................... Pag. 12
6. Control signal connections................................................................................................................... Pag. 14
6.1 Control signal connection by XLR5 plugs ......................................................................................... Pag. 14
7. Turning on the projector......................................................................................................................... Pag. 15
7.1 DMX address of the unit ........................................................................................................................... Pag. 15
8. DMX Chart............................................................................................................................................................ Pag. 16
8.1 DMX Chart 14, 8, 4, 1 channels ............................................................................................................. Pag. 16
8.2 DMX Chart 7 channels................................................................................................................................ Pag. 18
9. Display panel functions............................................................................................................................ Pag. 20
9.1 Quick guide to menu.................................................................................................................................. Pag. 20
9.2 Rapid count..................................................................................................................................................... Pag. 20
9.3 Main functions menu.................................................................................................................................. Pag. 21
9.4 Measure (MEAS)............................................................................................................................................ Pag. 24
9.5 Electronic alignment of the LEDs........................................................................................................... Pag. 26
9.6 Special functions of the fixture................................................................................................................. Pag. 27
9.7 Error messages............................................................................................................................................... Pag. 27
10. Accessories and spare parts.............................................................................................................. Pag. 28

4
11. Maintenance................................................................................................................................................... Pag. 30
11.1 Firmware update....................................................................................................................................... Pag. 30
11.2 Periodic cleaning....................................................................................................................................... Pag. 30
11.3 Periodic controls......................................................................................................................................... Pag. 30
11.4 Fuses................................................................................................................................................................ Pag. 30
12. F.A.Q. and answers................................................................................................................................... Pag. 31

5
Congratulations on having purchased a Coemar product. You have assured yourself of a fixture
of the highest quality, both in componentry and in the technology used. We renew our invitation
to you to complete the service information on the previous page, to expedite any request for
service information or spares (in case of problems encountered either during, or subsequent to,
installation). This information will assist in providing prompt and accurate advice from your Coemar
service centre. Following the instructions and procedures outlined in this manual will ensure the
maximum efficiency of this product for years to come.
1. Packaging and transportation
1.1 Packaging
Open the packaging and make sure that no part of the equipment has suffered any damage
during the transportation. In case of damage to the fixture, contact your currier and your supplier
immediately by telephone, fax or email, and inform them you will formally notify them in writing
through registered letter.
Packing list
Ensure the packaging contains:
1 Reflection LEDko FullSpectrum Series 2
1 Instruction manual
1 Main power plugs
2. General information
2.1 Safety informations
Fire prevention:
1. Never locate the fixture on any flammable surface.
2. Minimum distance from flammable materials: 0,5m.
3. Minimum distance from the closet illuminable surface: 0,5m.
4. Replace any blown or damaged fuse only with those of identical values. Refer
to the schematic diagram if there is any doubt.
5. Connect the projector to mains power protected by a thermal magnetic cir-
cuit breaker.
Prevention from electric shock:
1. Presence of high voltage inside of the fixture. Insulate the projector from mains
supply before opening or performing any function which involves touching
the inside of the fixture, including lamp replacement.
2. For the connection to the mains, adhere strictly to the guidelines outlined in
this manual.
1.2 Transportation
The LEDko FullSpectrum Series 2 should be transported in either its original packaging or in
an appropriate flight case.

6
Safety:
1. The projector must always be installed with bolts, clamps, or other fixing de-
vices which are suitably rated to support the weight of the projector.
2. Always use a secondary safety fixing device with chain or steel wire of a suit-
able rating to sustain the weight of the unit in case of failure of the principal
fixing point.
3. The external surfaces of the unit, at various points, may reach 60°C. Never
handle the unit until at least 10 minutes have elapsed since the LED was
turned off.
4. Never install the fixture in an enclosed area lacking sufficient air flow; the
room temperature must not exceed 35°C.
5. The projector contains electronic and electrical components which must un-
der no circumstances be in contact with water, oil or any other liquid. Failure
to do so will compromise the proper functioning of the projector.
2.2 Warranty conditions
1. The fixture is under warranty for 36 months from the purchase date against factory defec-
tions.
2. Damage ought to unskillfulness, inappropriate use, or lack of suggested maintenance are
excluded from the warranty.
3. Warranty expires when the projector is opened by unauthorized personnel.
4. Warranty doesn’t include the replacement of the fixture.
5. Serial number and model of the fixture are necessary to retrieve informations and assistance
from the dealer.
2.3 EC Norms
The projector meets all fundamental applicable EC requirements.
3. The level of technology of LEDko FullSpectrum Series 2 requires the use
of specialised personnel for all service applications; refer all work to your au-
thorised Coemar service centre.
4. A good earth connection is essential for the proper functioning of the projec-
tor. Never connect the fixture if there is no earth connection.
5. Mains cables must not come into contact with other cables.
6. Do not operate the projector with wet hands or in an area where water is
present.
7. The fixture must never be located in an exposed position, or in areas of ex-
treme humidity.

7
Power supply 90-230Vac, 50-60Hz
Maximum current 0.85 A a 230 VaC - 2.15 A a 90 Vac
Power factor Cosϕ= 0.98
Power consumption 180 watt
Color temperature RGBW, with pure colour mixing throughout the
field and all whites from 3200 to 10000 K
Weight (without optic) 6kg - 13.2lbs
Maximum room temperature 35°C
IP rating IP20
3. Product specifications
3.1 Technical characteristics
3.2 Dimensions
601mm
23.66”
369mm
145.3”
189mm
74.4”
355mm
139.8”
229mm
90.2”

8
3.3. Unit’s main components
Components description
AAdjustable yoke
BIris (optional)
CGobo holder (optional)
DLens adjusting handles
EYoke locking handle
FGel frame locking spring
GProfile blade
HInterchangeable optic
A
B
C
D
EF
G
H

9
3.4 Back panel description
Display
Menu button
Enter button
PowerCon In
PowerCon Out
Plus button
Minus button
DMX In
DMX Out

10
4. Installation
Remove the frontal cap by loosening the upper and lower screws enough to free the cap itself, set
the optic’s flange tilted about 60°. Insert the optic’s flange into the body’s receptacle and turn the
optic 60° until it is firmly assembled to the projector body, free to rotate but not free to detach itself
from the body. Ensure the optic to the body by tightening the two screws previously loosened.
4.1 Optical installation
Warning!!
When the protective cap is removed, never lean the fixture facing down.
The front lens can be seriously damaged.

11
4.2 Mechanical installation
LEDko FullSpectrum Series 2 may be hung from an appropriate structure in any position or
on tripode. If hanging the fixture from a lighting truss or similar, we recommend the use of an
appropriate clamp “A”, as shown in the following diagram.
Warning!!
Always ensure that your support structure
and fixing (bolts, clamps, etc…) are rated
A to support the weight of the fixture.
A
4.3 Safety chain
When hanging LEDko FullSpectrum Series 2 it is recommended to use a safety chain, as
required by current legislation. The safety chain must pass through the handles of the unit and
then attached to the structure.
If using steel cables and chains not Coemar’s production, make sure they are suitable to sup-
port the weight of the unit according to normative UL/ETL (required: the weight of 6 complete
devices for at least one hour).
4.4 Adjusting unit’s tilt
In order to adjust the tilt of the unit simply loose the side handle adjust the tilt and lock the yoke
by tightening the handle again.

12
5. Powering up
5.2 Connection to mains power
Mains cable characteristics
The mains cable provided is thermally resistant, complying to the most recent International stan-
dards.
Note: in case of cable replacement, similar cable with comparable thermal resistant qualities
must be used exclusively (cable 3 X 1,5 ø external 10 mm, rated 300/500V, tested
to 2 KV, operating temperature -40°C + 180°C, Coemar cod. CV5311).
Connection to mains power
LEDko FullSpectrum Series 2 is equipped with two power connectors, one as input and one
as output, which can be used to feed up to 8 (at 230 VAC) or 4 (90 VAC) fixtures
The max absorption of LEDko FullSpectrum Series 2 is reported in the following table:
- 230 VaC 0.85 A constant during normal exercise.
- 90 VaC 2.15 A constant during normal exercise.
5.1 Operating voltage and frequency
The unit may operates at voltages ranges from 90 to 250VaC at a frequency of 50 or 60 Hz. It is
not needed to effect any setup procedures: LEDko FullSpectrum Series 2 will automatically
adjust its operation to suit any frequency or voltage within this range.

13
Warning!!
•The use of a thermal/magnetic circuit breaker is recommended. Strict adherence to
regulatory norms is strongly recommended.
•LEDko FullSpectrum Series 2 should not be powered through a dimmer as this may
damage the internal switching power supply.
•Prior to connecting the device to mains power, ensure that the mains characteristics
are within the recommended range for the use of LEDko FullSpectrum Series 2.
•All cabling and connections should be carried out by a suitably qualified personnel.

14
Warning!
Make sure that screening and conductors are not in contact one another or with the
metal housing of the connector.
Pin#1 and housing must never be connected to the power supply unit.
6.1 Control signal connection by XLR5 plugs
The digital control signal is transmitted to the projector via a two pole cable screened in accord-
ing to the International standards for DMX 512 data transmission. The connection must be serial,
using connectors XLR5 male and female located on the back of LEDko FullSpectrum Series
2labelled DMX512 IN e OUT.
DMX In DMX Out
6. Control signal connections

15
A00 1
7. Turning on the projector
After having followed the preceding steps described, proceed with the power supply and turn on
the projector connecting it to the mains power.
The software version installed on the internal microprocessors will be shown on the display, sud-
denly it will show the current DMX addressing. If the address blinks, it means that the DMX signal
has not been received. Check the connection cable and the mixer functioning.
7.1 DMX address of the unit
Each projector can use 14, 8, 4, 1 or 7 address channels for its complete operation and is con-
trolled by a DMX 512 signal.
DMX addressing
When powered up initially, each projector will show A001, which indicates DMX address 001;
for example, when set at 14 channels a projector thus addressed will respond to commands
of channel 1 to 14 from your DMX 512 controller. A second unit must be addressed as A015,
a third one as A029 and so on. The operation must be carried out on every LEDko FullSpec-
trum Series 2 which has an address different from A001.
Altering the DMX address:
1. Press the + or – button until the display shows the required DMX address. The digits on the
display will blink to indicate that the variation has not been registered.
2. Press the enter key to confirm your selection. The digits on the display panel will cease to blink
and the projector will now respond to the new address.
Note: by holding the + or – button down the scrolling will be faster; thus allowing a faster
selection
Warning!!
If you alter the DMX address with no DMX signal connected, the digits on the display
panel will continue to flash even after you have pressed ENTER button to confirm the
address.

16
8. DMX chart
8.1 DMX Chart 14,8,4,1 channels
channel function type of
control effect decimal percentage
1 1 - 1 master
dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2 2 1 - red proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
3 3 2 - green proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
4 4 3 - blue proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
5 5 4 - white proportional proportional control of the color percentage
from 0 to 100% 0 - 255 0% - 100%
6 6 - - strobe
step no effect 0 - 9 0% - 4%
proportional variable speed strobing effect, from slow to fast 10 - 57 4% - 22%
step stop strobe 58 - 59 23% - 23%
proportional sequenced pulse effect, slow closing, fast opening
(variable speed pulsing, from slow to fast) 60 - 108 24% - 42%
step stop strobe 109 - 110 43% - 43%
proportional sequenced pulse effect, fast closing, slow opening
(variable speed pulsing, from slow to fast) 111 - 159 44% - 62%
step stop strobe 160 - 161 63% - 63%
proportional strobe effect with random ashes and synchronous
colors (variable speed from slow to fast) 162 - 207 64% - 81%
step stop strobe 208 - 209 82% - 82%
proportional strobe effect with random ashes and synchronous
colors (variable speed from slow to fast) 210 - 255 82% - 100%
7 7 - - dimmer
ne proportional ne dimmer control 16 bit 0 - 255 0% - 100%
8 8 - - special
functions
step
park, no effect 0 - 71 0% - 28%
600 Hz 72 - 84 28% - 33%
fan at low-noise speed 85 - 96 33% - 38%
fan at auto-silent speed 97 - 108 38% - 42%
proportional fan speed control from minimum to maximum 109 - 120 43% - 47%
step
no effect 121 - 133 47% - 52%
enables the automatic display blackout 134 - 185 53% - 73%
disables the automatic display blackout 186 - 199 73% - 78%
LED control frequency tuning 1000 Hz 200 - 205 78% - 80%
LED control frequency tuning 3000 Hz 206 - 211 81% - 83%
LED control frequency tuning 6000 Hz 212 - 217 83% - 85%
LED control frequency tuning 8000 Hz 218 - 223 85% - 87%
LED control frequency tuning 10000 Hz 224 - 229 88% - 90%
LED control frequency tuning 12000 Hz 230 - 235 90% - 92%
LED control frequency tuning 14000 Hz 236 - 241 93% - 95%
LED control frequency tuning 16000 Hz 242 - 247 95% - 97%
LED control frequency tuning 19000 Hz 248 - 255 97% - 100%

17
9 - - - red tone step
no effect 0 - 9 0% - 4%
RED preset 1 10 - 71 4% - 28%
RED preset 2 72 - 133 28% - 52%
RED preset 3 134 - 195 53% - 76%
RED preset 4 196 - 255 77% - 100%
10 - - - green tone step
no effect 0 - 9 0% - 4%
GREEN preset 1 10 - 71 4% - 28%
GREEN preset 2 72 - 133 28% - 52%
GREEN preset 3 134 - 195 53% - 76%
GREEN preset 4 196 - 255 77% - 100%
11 - - - blue tone proportional
no effect 0 - 9 0% - 4%
BLUE preset 1 10 - 71 4% - 28%
BLUE preset 2 72 - 133 28% - 52%
BLUE preset 3 134 - 195 53% - 76%
BLUE preset 4 196 - 255 77% - 100%
12 - - - white tone
step no effect 0 - 9 0% - 4%
step WHITE 3200 K 10 - 15 4% - 6%
proportional proportional value from 3200 K to 4000 K 16 - 30 6% - 12%
step WHITE 4000 K 31 - 45 12% - 18%
proportional proportional value from 4000 K to 5000 K 46 - 60 18% - 24%
step WHITE 5000 K 61 - 75 24% - 29%
proportional proportional value from 5000 K to 5600 K 76 - 90 30% - 35%
step WHITE 5600 K 91 - 105 36% - 41%
proportional proportional value from 5600 K to 4000 K 106 - 120 42% - 47%
step WHITE 6000 K 121 - 135 47% - 53%
proportional proportional value from 6000 K to 7000 K 136 - 150 53% - 59%
step WHITE 7000 K 151 - 165 59% - 65%
proportional proportional value from 7000 K to 8000 K 166 - 180 65% - 71%
step WHITE 8000 K 181 - 195 71% - 76%
proportional proportional value from 8000 K to 9000 K 196 - 210 77% - 82%
step WHITE 9000 K 211 - 225 83% - 88%
proportional proportional value from 9000 K to 10000 K 226 - 240 89% - 94%
step WHITE 10000 K 241 - 255 95% - 100%
13 - - - green
saturation
step no effect 0 0%
proportional exalts the green color in the mixing and diminishes
the presence of magenta 1 - 127 0% - 50%
step no effect 128 50%
proportional dimishes the presence of green in the mixing and
exalts the green color 129 - 254 51% - 99%
step no effect 255 100%
14 - - - saturation proportional the white tone fades to the tone built with the
RGBW channels 0 - 255 0% - 100%
Note 1: colors macros of channels 9-10-11-12 can also be obtained through the mixing of channels 2-3-4-5.
Note 2: the one channel function mode can be selected through the DMX function menu. The color of the light will
be a white 5600 K.
Note 3: the rest position of the +- green DMX channel is 128. Diminishing the DMX value augments the presence of
the green color. Increasing the DMX value augments the presence of magenta.
Note 4: increasing the value of the saturation DMX channel the white light will fade to the color selected with the
color wheel DMX channel.

18
8.2 DMX Chart 7 channels
channel function type of
control effect decimal percentage
1 master dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
2color
temperature
step WHITE 3200 K 0 - 15 0% - 6%
proportional proportional value from 3200 K to 4000 K 16 - 30 6% - 12%
step WHITE 4000 K 31 - 45 12% - 18%
proportional proportional value from 4000 K to 5000 K 46 - 60 18% - 24%
step WHITE 5000 K 61 - 75 24% - 29%
proportional proportional value from 5000 K to 5600 K 76 - 90 30% - 35%
step WHITE 5600 K 91 - 105 36% - 41%
proportional proportional value from 5600 K to 6000 K 106 - 120 42% - 47%
step WHITE 6000 K 121 - 135 47% - 53%
proportional proportional value from 6000 K to 7000 K 136 - 150 53% - 59%
step WHITE 7000 K 151 - 165 59% - 65%
proportional proportional value from 7000 K to 8000 K 166 - 180 65% - 71%
step WHITE 8000 K 181 - 195 71% - 76%
proportional proportional value from 8000 K to 9000 K 196 - 210 77% - 82%
step WHITE 9000 K 211 - 225 83% - 88%
proportional proportional value from 9000 K to 10000 K 226 - 240 89% - 94%
step WHITE 10000 K 241 - 255 95% - 100%
3green
saturation
step no effect 0 0%
proportional exalts the green color in the mixing and diminishes
the presence of magenta 1 - 127 0% - 20%
step no effect 128 50%
proportional diminishes the presence of green in the mixing and
exalts the green color 129 - 254 51% - 99%
step no effect 255 100%
4 saturation proportional the white tone fades to the tone built with the
RGBW channels 0 - 255 0% - 100%
5 hue proportional reproduce the sequence of red, green and blue
with its mixing 0 - 255 0% - 100%
6dimmer ne proportional ne dimmer control 16 bit 0 - 255 0% - 100%

19
7special
functions
step
park, no effect 0 - 71 0% - 28%
600 Hz 72 - 84 28% - 33%
fan at low-noise speed 85 - 96 33% - 38%
fan at auto-silent speed 97 - 108 38% - 42%
proportional fan speed control from minimum to maximum 109 - 120 43% - 47%
step
no effect 121 - 133 47% - 52%
enables the automatic display blackout 134 - 185 53% - 73%
disables the automatic display blackout 186 - 199 73% - 78%
LED control frequency tuning 1000 Hz 200 - 205 78% - 80%
LED control frequency tuning 3000 Hz 206 - 211 81% - 83%
LED control frequency tuning 6000 Hz 212 - 217 83% - 85%
LED control frequency tuning 8000 Hz 218 - 223 85% - 87%
LED control frequency tuning 10000 Hz 224 - 229 88% - 90%
LED control frequency tuning 12000 Hz 230 - 235 90% - 92%
LED control frequency tuning 14000 Hz 236 - 241 93% - 95%
LED control frequency tuning 16000 Hz 242 - 247 95% - 97%
LED control frequency tuning 19000 Hz 248 - 255 97% - 100%
Note 1: the reset position of the +- green DMX channel is 128. Diminishing the DMX value augments the presence of
the green. Increasing the DMX value augments the presence of magenta.
Note 2: increasing the value of the saturation DMX channel the white light will fade to the color selectedwith the color
wheel DMX channel

20
9. Display panel functions
9.1 Quick guide to menu
To access the functions menus just press the MENU button. Then press + or – buttons to scroll
the pages and press the ENTER button to access to any other function.
By suitably using all the functions of LEDko FullSpectrum Series 2, which can be activated
through its display panel, it is possible to change some of the parameters and to add some func-
tions. Changing the preset settings made by Coemar can vary the functions of the projector
so that it will respond differently to the controller; therefore carefully read about the functions
described here before carrying out any possible selection.
9.2 Rapid count
Through the display panel of LEDko FullSpectrum Series 2 it is possible to quickly change the
various numbers displayed for the different functions in the following 3 manners:
1. Pressing the + or – buttons will cause the count to be quicker.
2. Pressing first + and then – and then holding them down simultaneously will cause the num-
bers to jump to the highest value.
3. Pressing first – and then + and then holding them down simultaneously will cause the num-
ber to jump to the lowest value.