Coemar LEDko FullSpectrum 6 HD User manual

Version 1.0
FullSpectrum 6 HD
Instruction manual

2
Please note in the space provided above the relative service information of the model and the
retailer from whom you purchased your LEDko FullSpectrum 6 HD: this information will assist
us in providing spare parts, repairs or in answering any technical enquiries with the utmost speed
and accuracy.
WARNING: the security of the xture is granted only if these instructions are strictly followed;
therefore it is absolutely necessary to keep this manual.
User Manual version 1.0
Edition January 2019
Fixture code:
.............................................................................................................................................................
Purchase date:
.............................................................................................................................................................
Dealer:
.............................................................................................................................................................
Address:
.............................................................................................................................................................
Suburb:
.............................................................................................................................................................
Country:
.............................................................................................................................................................
Phone / Fax:
.............................................................................................................................................................
FullSpectrum 6 HD

3
Index
1. Packaging and transportation........................................................................................................Pag. 5
1.1. Packaging...........................................................................................................................................Pag. 5
1.2. Transportation...................................................................................................................................Pag. 5
2. General information............................................................................................................................Pag. 5
2.1 Safety informations...........................................................................................................................Pag. 5
2.2 Warranty conditions.........................................................................................................................Pag. 6
2.3 EC Norms............................................................................................................................................Pag. 6
3. Product specications..................................................................................................................... Pag. 7
3.1 Technical characteristics.................................................................................................................Pag. 7
3.2 Dimensions.........................................................................................................................................Pag. 7
3.3 Unit’s main components.................................................................................................................Pag. 8
3.4 Back panel description....................................................................................................................Pag. 9
4. Installation........................................................................................................................................... Pag. 10
4.1 Optical Installation.......................................................................................................................... Pag. 10
4.2 Mechanical installation.................................................................................................................. Pag. 11
4.3 Safety chain..................................................................................................................................... Pag. 11
4.4 Adjusting unit’s tilt.......................................................................................................................... Pag. 11
5. Powering up.......................................................................................................................................... Pag. 12
5.1 Operating voltage and frequency ............................................................................................... Pag. 12
5.2 Connection to mains power......................................................................................................... Pag. 12
6. Control signal connections........................................................................................................... Pag. 13
6.1 Control signal connection by XLR5 plugs ................................................................................. Pag. 13
7. Turning on the projector.................................................................................................................. Pag. 14
7.1 DMX address of the unit ................................................................................................................ Pag. 14
8. DMX Chart ............................................................................................................................................. Pag. 15
8.1 DMX Chart: 16, 7, 1 channels ......................................................................................................... Pag. 15
8.2 DMX Chart: Studio mode ............................................................................................................. Pag. 18
8.3 DMX Chart: RGB mode ................................................................................................................. Pag. 19
9. Display panel functions.................................................................................................................. Pag. 21
9.1 Quick guide to menu....................................................................................................................... Pag. 21
9.2 Rapid count..................................................................................................................................... Pag. 21
9.3 Main functions menu.................................................................................................................... Pag. 24
9.4 Measure ........................................................................................................................................... Pag. 24
9.5 Color presets .................................................................................................................................. Pag. 26
9.6 Special functions of the xture................................................................................................... Pag. 29
9.7 Error messages............................................................................................................................... Pag. 29
10. Accessories and spare parts...................................................................................................... Pag. 30

4
11. Maintenance....................................................................................................................................... Pag. 32
11.1 Firmware update........................................................................................................................... Pag. 32
11.2 Periodic cleaning.......................................................................................................................... Pag. 32
11.3 Periodic controls........................................................................................................................... Pag. 32
11.4 Fuses............................................................................................................................................... Pag. 32
12. F.A.Q. and answers.......................................................................................................................... Pag. 33

5
Congratulations on having purchased a Coemar product. You have assured yourself of a xture
of the highest quality, both in componentry and in the technology used. We renew our invitation
to you to complete the service information on the previous page, to expedite any request for
service information or spares (in case of problems encountered either during, or subsequent
to, installation). This information will assist in providing prompt and accurate advice from your
Coemar service centre. Following the instructions and procedures outlined in this manual will
ensure the maximum eciency of this product for years to come.
1. Packaging and transportation
1.1 Packaging
Open the packaging and make sure that no part of the equipment has suered any damage
during the transportation. In case of damage to the xture, contact your currier and your supplier
immediately by telephone, fax or email, and inform them you will formally notify them in writing
through registered letter.
Packing list
Ensure the packaging contains:
1 Reection LEDko FullSpectrum 6 HD
1 Instruction manual
1 Main power plugs
2. General information
2.1 Safety informations
Fire prevention:
1. Never locate the xture on any ammable surface.
2. Minimum distance from ammable materials: 0,5m.
3. Minimum distance from the closet illuminable surface: 0,5m.
4. Replace any blown or damaged fuse only with those of identical values. Refer
to the schematic diagram if there is any doubt.
5. Connect the projector to mains power protected by a thermal magnetic circuit
breaker.
Prevention from electric shock:
1. Presence of high voltage inside of the xture. Insulate the projector from mains
supply before opening or performing any function which involves touching
the inside of the xture, including lamp replacement.
2. For the connection to the mains, adhere strictly to the guidelines outlined in
this manual.
1.2 Transportation
The LEDko FullSpectrum 6 HD should be transported in either its original packaging or in an
appropriate ight case.

6
Safety:
1. The projector must always be installed with bolts, clamps, or other xing
devices which are suitably rated to support the weight of the projector.
2. Always use a secondary safety xing device with chain or steel wire of a
suitable rating to sustain the weight of the unit in case of failure of the principal
xing point.
3. The external surfaces of the unit, at various points, may reach 60°C. Never
handle the unit until at least 10 minutes have elapsed since the LED was
turned o.
4. Never install the xture in an enclosed area lacking sucient air ow; the room
temperature must not exceed 35°C.
5. The projector contains electronic and electrical components which must under
no circumstances be in contact with water, oil or any other liquid. Failure to do
so will compromise the proper functioning of the projector.
2.2 Warranty conditions
1. The xture is under warranty for 36 months from the purchase date against factory defec-
tions.
2. Damage ought to unskillfulness, inappropriate use, or lack of suggested maintenance are
excluded from the warranty.
3. Warranty expires when the projector is opened by unauthorized personnel.
4. Warranty doesn’t include the replacement of the xture.
5. Serial number and model of the xture are necessary to retrieve informations and assistance
from the dealer.
2.3 EC Norms
The projector meets all fundamental applicable EC requirements.
3. The level of technology of LEDko FullSpectrum 6 HD requires the use of
specialised personnel for all service applications; refer all work to your
authorised Coemar service centre.
4. A good earth connection is essential for the proper functioning of the projector.
Never connect the xture if there is no earth connection.
5. Mains cables must not come into contact with other cables.
6. Do not operate the projector with wet hands or in an area where water is
present.
7. The xture must never be located in an exposed position, or in areas of extreme
humidity.

7
Power supply 90-230Vac, 50-60Hz
Maximum current 1.06 A at 230 V, 2.71 A at 90 V
Power factor Cosϕ= 0.9
Power consumption 220 watt
Color temperature RGBWLA, with pure color mixing throughout the eld
and all whites from 2700 to 6500 K
Weight (without optic) 6kg - 13.2lbs
Maximum ambient temperature +35°C / +95°F
IP rating IP20
3. Product specications
3.1 Technical characteristics
3.2 Dimensions
601mm
23.66”
369mm
145.3”
189mm
74.4”
355mm
139.8”
229mm
90.2”

8
3.3. Unit’s main components
Components description
AAdjustable yoke
BIris (optional)
CGobo holder (optional)
DLens adjusting handles
EYoke locking handle
FGel frame locking spring
GProle blade
HInterchangeable optic
A
B
C
D
EF
G
H

9
3.4 Back panel description
Display
Menu button /
Enter button
Back button
PowerCon Out
PowerCon In
Plus button
Minus button
DMX In
DMX Out
Exit button
Color preset
button

10
4. Installation
Remove the frontal cap by loosening the upper and lower screws enough to free the cap itself, set
the optic’s ange tilted about 60°. Insert the optic’s ange into the body’s receptacle and turn the
optic 60° until it is rmly assembled to the projector body, free to rotate but not free to detach itself
from the body. Ensure the optic to the body by tightening the two screws previously loosened.
4.1 Optical installation
Warning!!
When the protective cap is removed, never lean the xture facing down.
The front lens can be seriously damaged.

11
4.2 Mechanical installation
LEDko FullSpectrum 6 HD may be hung from an appropriate structure in any position or
on tripode. If hanging the xture from a lighting truss or similar, we recommend the use of an
appropriate clamp “A”, as shown in the following diagram.
Warning!!
Always ensure that your support structure
and xing (bolts, clamps, etc…) are rated
A to support the weight of the xture.
A
4.3 Safety chain
When hanging it is recommended to use a safety chain, as required by current legislation. The
safety chain must pass through the handles of the unit and then attached to the structure.
If using steel cables and chains not ’s production, make sure they are suitable to support the
weight of the unit according to normative UL/ETL (required: the weight of 6 complete devices
for at least one hour).
4.4 Adjusting unit’s tilt
In order to adjust the tilt of the unit simply loose the side handle adjust the tilt and lock the yoke
by tightening the handle again.

12
5. Powering up
5.2 Connection to mains power
Mains cable characteristics
The mains cable provided is thermally resistant, complying to the most recent International
standards.
Note: in case of cable replacement, similar cable with comparable thermal resistant qualities
must be used exclusively (cable 3 X 1,5 ø external 10 mm, rated 300/500V, tested to 2 KV, op-
erating temperature -40°C + 180°C, Coemar cod. CV5311).
Connection to mains power
LEDko FullSpectrum 6 is equipped with two power connectors, one as input and one as out-
put, which can be used to feed up to 8 (at 230 VAC) or 4 (90 VAC) xtures.
The max absorption of LEDko FullSpectrum 6 HD is reported in the following table:
- 230 VaC 1.06 A constant during normal exercise.
- 90 VaC 2.71 A constant during normal exercise.
5.1 Operating voltage and frequency
The unit may operates at voltages ranges from 90 to 250VaC at a frequency of 50 or 60 Hz. It
is not needed to eect any setup procedures: LEDko FullSpectrum 6 HD will automatically
adjust its operation to suit any frequency or voltage within this range.
brown
blue
yellow/green
neutral
mass
fase

13
Warning!!
• The use of a thermal/magnetic circuit breaker is recommended. Strict adherence to
regulatory norms is strongly recommended.
• LEDko FullSpectrum 6 HD should not be powered through a dimmer as this may
damage the internal switching power supply.
• Prior to connecting the device to mains power, ensure that the mains characteristics are
within the recommended range for the use of LEDko FullSpectrum 6 HD.
• All cabling and connections should be carried out by a suitably qualied personnel.
Warning!
Make sure that screening and conductors are not in contact one another or with the
metal housing of the connector.
Pin#1 and housing must never be connected to the power supply unit.
6.1 Control signal connection by XLR5 plugs
The digital control signal is transmitted to the projector via a two pole cable screened in
according to the International standards for DMX 512 data transmission. The connec-
tion must be serial, using connectors XLR5 male and female located on the back of LEDko
FullSpectrum 6 HD labelled DMX512 IN e OUT.
6. Control signal connections

14
7. Turning on the projector
After having followed the preceding steps described, proceed with the power supply and turn on
the projector connecting it to the mains power.
The software version installed on the internal microprocessors will be shown on the display, sud-
denly it will show the current DMX addressing. If the address blinks, it means that the DMX signal
has not been received. Check the connection cable and the mixer functioning.
7.1 DMX address of the unit
Each projector can use 16/7/1 or Studio mode for its complete operation and is controlled by a
DMX 512 signal.
DMX addressing
When powered up initially, each projector will show A001, which indicates DMX address
001; for example, when set at 16 channels a projector thus addressed will respond to com-
mands of channel 1 to 16 from your DMX 512 controller. A second unit must be addressed
as A017, a third one as A033 and so on. The operation must be carried out on every LEDko
FullSpectrum 6 HD which has an address dierent from A001.
Altering the DMX address:
1. Press the + or – button until the display shows the required DMX address. The digits on the
display will blink to indicate that the variation has not been registered.
2. Press the enter key to conrm your selection. The digits on the display panel will cease to
blink and the projector will now respond to the new address.
Note: by holding the + or – button down the scrolling will be faster; thus allowing a faster selec-
tion
Warning!!
If you alter the DMX address with no DMX signal connected, the digits on the display
panel will continue to ash even after you have pressed ENTER button to conrm the
address.
A001
DMX address

15
8. DMX chart
8.1 DMX Chart 16, 7, 1 channels
channel function type of
control eect decimal percentage
111 master
dimmer proportional adjust luminous output intensity from 0 to 100% 0-255 0% -100%
2 2 - red proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
3 3 - green proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
4 4 - blue proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
5 5 - white proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
6 6 - lime proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
7 7 - amber proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
8- - strobe eect
step no eect 0-9 0% -4%
proportional variable speed strobing eect, from slow
to fast 10 -57 4% -22%
step stop strobe 58 -59 23% -23%
proportional
sequenced pulsed strobe, slow closing,
fast operating (variable speed pulsing,
from slow to fast)
60 -108 24% -42%
step stop strobe 109 -110 43% -43%
proportional
sequenced pulsed strobe, fast closing,
slow operating (variable speed pulsing,
from slow to fast)
111 -159 44% -62%
step stop strobe 160 -161 63% -63%
proportional random strobe eect with variable speed
from slow to fast and synchronized colors 162 -207 64% -81%
step stop strobe 208 -209 82% -82%
proportional
random strobe eect with variable speed
from slow to fast and
non-synchonized colors
210 -255 82% -100%
9 - - dimmer ne proportional ne dimmer control 16 bit 0-255 0% -100%

16
10 - - special
functions
step
no eect 0-84 0% -33%
fan at low-noise speed 85 -96 33% -38%
fan at auto-speed 97 -108 38% -42%
fan at studio speed 109 -121 43% -47%
proportional fan speed control from minimum to
maximum 122 -134 47% -52%
step
enables the automatic display blackout 135 -185 53% -73%
disables the automatic display blackout 186 -199 73% -78%
no eect 200 -255 78% -100%
11 - - red tone step
no eect 0-9 0% -4%
R24 - Scarlet red 10 -34 4% -13%
R02 - Bastard amber 35 -59 14% -23%
R313 - Light relief yellow 60 -84 24% -33%
R18 - Flame 85 -109 33% -43%
R331 - Shell pink 110 -134 43% -53%
R25 - Orange red 135 -159 53% -62%
R46 - Magenta 160 -184 63% -72%
R08 - Pale gold 185 -209 73% -82%
R27 - Medium red 210 -234 82% -92%
R318 - Mayan sun 235 -255 92% -100%
12 - - green tone step
no eect 0-9 0% -4%
R4460 - Calcolor 60 green 10 -34 4% -13%
R2004 - Storaro green 35 -59 14% -23%
E730 - Liberty green 60 -84 24% -33%
E088 - Lime green 85 -109 33% -43%
R90 - Kelly green 110 -134 43% -53%
R395 - Teal green 135 -159 53% -62%
R91 - Primary green 160 -184 63% -72%
R393 - Emerald green 185 -209 73% -82%
R393 - Leaf green 210 -234 82% -92%
R86 - Pea green 235 -255 92% -100%
13 - - blue tone step
no eect 0-9 0% -4%
R2008 - Storaro indigo 10 -34 4% -13%
E5058 - French lilac 35 -59 14% -23%
R369 - Tahitian blue 60 -84 24% -33%
R347 - Belladonna rose 85 -109 33% -43%
R381 - Baldassari blue 110 -134 43% -53%
R57 - Lavander 135 -159 53% -62%
R55 - Lilac 160 -184 63% -72%
R4790 - Calcolor 90 magenta 185 -209 73% -82%
R92 - Turquise 210 -234 82% -92%
R370 - Italian blue 235 -255 92% -100%

17
14 - - white tone
step no eect 0-9 0% -4%
2700 K 10 -30 4% -12%
proportional proportional value from 2700 K to 3200 K 31 -52 12% -20%
step 3200 K 53 -74 21% -29%
proportional proportional value from 3200 k to 4000 K 75 -96 29% -38%
step 4000 K 97 -118 38% -46%
proportional proportional value from 4000 K to 5000 K 119 -140 47% -55%
step 5000 K 141 -162 55% -64%
proportional proportional value from 5000 K to 5600 K 163 -184 64% -72%
step 5600 K 185 -206 73% -81%
proportional proportional value from 5600 K to 6500 K 207 -228 81% -89%
step 6500 K 229 -255 90% -100%
15 - - green
saturation
step no eect 0-9 0% -4%
proportional exalts the green color in the mixing and
diminishes the presence of magenta 10 -123 4% -48%
step no eect 124 -132 49% -52%
proportional diminishes the presence of green in the
mixing and exalts the magenta color 133 -246 52% -96%
step no eect 247 -255 97% -100%
16 - - saturation proportional the white tone fades to the tone built with
RGBWLA channels 0-255 0% -100%
NOTE 1: channels involving 10 - 11 - 12 macro colors can also be obtained by mixing channels
2 - 3 - 4 - 5 - 6 - 7.
NOTE 2: to use the one channel mode function select the CCT or the color gel from the display.
NOTE 3: the rest position of the green saturation is 128. Diminishing the DMX value augments the
presence of the green color. Increasing the DMX value augments the presence of magenta.
NOTE 4: increasing the value of the Saturation DMX channel the white tone (channel 14) will fade
to the color selected by the channel 2, 3, 4, 5, 6 or 7.

18
8.2 DMX Chart Studio mode
channel function type of
control eect decimal percentage
1master
dimmer proportional adjust luminous output intensity from 0 to 100% 0-255 0% -100%
2white tone step
3200 K 0 -10 0% -4%
2700 K 11 -16 4% -6%
2800 K 17 -22 7% -9%
2900 K 23 -28 9% -11%
3000 K 29 -34 11% -13%
3100 K 35 -40 14% -16%
3200 K 41 -46 16% -18%
3300 K 47 -52 18% -20%
3400 K 53 -58 21% -23%
3500 K 59 -64 23% -25%
3600 K 65 -70 25% -27%
3700 K 71 -76 28% -30%
3800 K 77 -82 30% -32%
3900 K 83 -88 33% -35%
4000 K 89 -94 35% -37%
4100 K 95 -100 37% -39%
4200 K 101 -106 40% -42%
4300 K 107 -112 42% -44%
4400 K 113 -118 44% -46%
4500 K 119 -124 47% -49%
4600 K 125 -130 49% -51%
4700 K 131 -136 51% -53%
4800 K 137 -142 54% -56%
4900 K 143 -148 56% -58%
5000 K 149 -154 58% -60%
5100 K 155 -160 61% -63%
5200 K 161 -166 63% -65%
5300 K 167 -172 65% -67%
5400 K 173 -178 68% -70%
5500 K 179 -184 70% -72%
5600 K 185 -190 73% -75%
5700 K 191 -196 75% -77%
5800 K 197 -202 77% -79%
5900 K 203 -208 80% -82%
6000 K 209 -214 82% -84%
6100 K 215 -220 84% -86%
6200 K 221 -226 87% -89%
6300 K 227 -232 89% -91%
6400 K 233 -238 91% -93%
6500 K 239 -244 94% -96%
5600 K 245 -255 96% -100%

19
3green
saturation
step no eect 0-9 0% -4%
proportional exalts the green color in the mixing and
diminishes the presence of magenta 10 -123 4% -48%
step no eect 124 -132 49% -52%
proportional diminishes the presence of green in the
mixing and exalts the magenta color 133 -246 52% -96%
step no eect 247 -255 97% -100%
4saturation proportional the white tone fades to the tone built with
the RGBW channels 0-255 0% -100%
5hue proportional reproduce the color crossfades around
the color space 0-255 0% -100%
6dimmer ne proportional ne dimmer control 16 bit 0-255 0% -100%
7special
functions
step
no eect 0-84 0% -33%
fan at low-noise speed 85 -96 33% -38%
fan at auto-speed 97 -108 38% -42%
fan at studio speed 109 -121 43% -47%
proportional fan speed control from minimum to
maximum 122 -134 47% -52%
step
enables the automatic display blackout 135 -185 53% -73%
disables the automatic display blackout 186 -199 73% -78%
no eect 200 -255 78% -100%
NOTE 1: the rest position of green saturation is 128. Diminishing the DMX value augments the
presence of the green color. Increasing the DMX value augments the presence of magenta.
NOTE 2: Increasing the value of the Saturation DMX channel (channel 4) the white light will fade to the
color selected with the HUE channel (channel 5)

20
8.2 DMX Chart RGB mode
channel function type of
control eect decimal percentage
1master
dimmer proportional adjust luminous output intensity from 0 to 100% 0-255 0% -100%
2dimmer ne proportional ne dimmer control 16 bit 0-255 0% -100%
3red proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
4green proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
5blue proportional proportional control of the color
percentage from 0 to 100% 0-255 0% -100%
6white tone
step no eect 0-9 0% -4%
2700 K 10 -30 4% -12%
proportional proportional value from 2700 K to 3200 K 31 -52 12% -20%
step 3200 K 53 -74 21% -29%
proportional proportional value from 3200 k to 4000 K 75 -96 29% -38%
step 4000 K 97 -118 38% -46%
proportional proportional value from 4000 K to 5000 K 119 -140 47% -55%
step 5000 K 141 -162 55% -64%
proportional proportional value from 5000 K to 5600 K 163 -184 64% -72%
step 5600 K 185 -206 73% -81%
proportional proportional value from 5600 K to 6500 K 207 -228 81% -89%
step 6500 K 229 -255 90% -100%
7saturation proportional the white tone fades to the tone built with the
RGBW channels 0-255 0% -100%
8strobe
eect
step no eect 0-9 0% -4%
proportional variable speed strobing eect, from slow to fast 10 -57 4% -22%
step stop strobe 58 -59 23% -23%
proportional
sequenced pulsed strobe,
slow closing, fast operating
(variable speed pulsing, from slow to fast)
60 -108 24% -42%
step stop strobe 109 -110 43% -43%
proportional
sequenced pulsed strobe,
fast closing, slow operating
(variable speed pulsing, from slow to fast)
111 -159 44% -62%
step stop strobe 160 -161 63% -63%
proportional random strobe eect with variable speed from
slow to fast and synchronized colors 162 -207 64% -81%
step stop strobe 208 -209 82% -82%
proportional random strobe eect with variable speed from
slow to fast and non-synchonized colors 210 -255 82% -100%
9special
functions
step
no eect 0-84 0% -33%
fan at low-noise speed 85 -96 33% -38%
fan at auto-speed 97 -108 38% -42%
fan at studio speed 109 -121 43% -47%
proportional fan speed control from minimum to maximum 122 -134 47% -52%
step
enables the automatic display blackout 135 -185 53% -73%
disables the automatic display blackout 186 -199 73% -78%
no eect 200 -255 78% -100%