Coemar Infinity Wash XL User manual

manuale di istruzioni
instructions manual
Version 1.0

∞Infinity Wash XL
serial number
date of purchase
retailer
address
suburb
capital city
state
tel./fax/
Please note in the space provided above the relative service information of the model and the retailer from
whom you purchased your
Infinity Wash XL : This information will assist us in answering any technical
enquiries with the utmost speed and accuracy.
WARNING : t he security of the fixture is granted only if these instructions are strictly followed; therefore it is
absolutely necessary to keep this manual.
Users Manual Version 1.0
edition February 2007

Index
1. Packaging and transportation Pag. 6
1.1. Packaging “6
1.2. Transportation “6
2. General information Pag. 6
2.1. Important safety information “6
2.2. Warranty conditions “7
2.3. CE norms “7
3. Product specifications Pag. 7
3.1. Technical characteristics “7
3.2. Dimensions “7
3.3. Projector components “7
4. Installation Pag. 8
4.1. Mechanical installation “8
4.2. Safety connections “8
5. Powering up Pag. 9
5.1. Operating voltage and frequency “9
5.2. Altering the operating voltage and frequency “9
5.3. Mains connection “10
6. DMX signal connection Pag. 11
7. Turning on the projector Pag. 12
7.1. DMX addressing “12
7.2. DMX functions “13
8. Display panel functions Pag. 15
8.1. Quick guide to menu navigation “15
8.2. Measure and test (MEAS) “16
8.3. Function settings (FUNC) “17
8.4. Rapid scrolling “17
8.5. Connecting the DR1 “18
8.6. Turning on the projector with no articulated movement “18
8.7. Resetting counters “18
9. Lamp installation and alignment Pag. 19
9.1. Lamp installation “19
9.2. Aligning the lamp in the optical path “20
10. Removing the colour changer assembly Pag. 21
11. Maintenance Pag. 22
11.1. Periodic cleaning “22
11.2. Periodic maintenance “22
11.3. Fuse replacement “22
11.4. Electronic motor alignment “23
12. Spare parts Pag. 23
13. Error messages Pag. 24
14. Frequently asked questions Pag. 25
5
English

Congratulations on having purchased a Coemar product. You have assured yourself of a fixture of the highest quality, both in compo-
nentry and in the technology used. We renew our invitation to you to complete the service information on the previous page, to expe-
dite any request for service information or spares (in case of problems encountered either during, or subsequent to, installation). This
information will assist in providing prompt and accurate advice from your Coemar service centre.
Following the instructions and procedures outlined in this manual will ensure the maximum efficiency of this product for years to come.
1.1. Packaging
Open the packaging and ensure that no part of the equipment has suffered damage in transit. In case of damage to the equipment,
contact your carrier immediately by telephone or fax, following this with formal notification in writing.
Packing list
Ensure the packaging contains:
1 Infinity Wash XL
1 instruction manual
2 cam-lock support brackets
1.2. Transportation
The Infinity Wash XL should be transported in its original packaging or in an appropriate flight case.
2.1. Important safety information
Fire prevention:
1. Infinity Wash XL utilises a Philips MSR GOLD 1200 SA/SE FastFit; the use of any alternative lamp is not recommended and will
null and void the fixture’s warranty.
2. Never locate the fixture on any flammable surface.
3. Minimum distance from flammable materials: 0,5 m.
4. Minimum distance from the closest illuminable surface: 2 m.
5. Replace any blown or damaged fuses only with those of identical values. Refer to the schematic diagram if there is any doubt.
6. Connect the projector to mains power via a thermal magnetic circuit breaker.
Preventing electric shock:
1. High voltage is present in the internals of the unit. Isolate the projector from mains supply prior to performing any function which
involves touching the internals of the unit, including lamp replacement.
2. For mains connection, adhere strictly to the guidelines outlined in this manual.
3. The level of technology inherent in the Infinity Wash XL requires the use of specialised personnel for all service applications; refer all
work to your authorised Coemar service centre.
4. A good earth connection is essential for proper functioning of the projector.
5. Mains cables should not come into contact with other cables. Never operate the unit without proper earth connection.
6. Do not operate the projector with wet hands or in an area where water present.
7. The fixture should never be located in an exposed position, or in areas of extreme humidity. A steady supply of circulating air is essential.
Protection against ultraviolet radiation:
1. Never turn on the lamp if any of the lenses, filters, or the carbon fibre housing is damaged; their respective functions will only operate
efficiently if they are in perfect working order.
2. Never look directly into the lamp when it is operating.
Safety:
1. The projector should always be installed with bolts, clamps, and other fixings which are suitably rated to support the weight of the unit.
2. Always use a secondary safety chain of a suitable rating to sustain the weight of the unit in case of the failure of the primary fixing point.
3. The external surface of the unit, at various points, may exceed 150°C. Never handle the unit until at least 10 minutes have elapsed
since the lamp was turned off.
4. Always replace the lamp if any physical damage is evident.
5. Never install the fixture in an enclosed area lacking sufficient air flow; the ambient temperature should not exceed 35°C.
6. Wait at least 10 minutes after the unit has been turned off prior to attempting to replace the lamp.
7. The proejctor contains electronic and electrical components which should under no circumstances be exposed to contact with water,
oil or any other liquid. Failure to do so will compromise the proper functioning of the projector.
Articulated movement
The projector has a pan range of 540° in its base and a tilt range 262° in its yoke; do not obstruct the projector whilst it is undertaking
articulated movement.
Forced ventilation
You will note several air vents on the body of the projector. To avoid any problems associated with overheating, never obstruct any of
these vents as this may seriously compromise the proper operation of the unit.
Protection rating against penetration by external agents:
1. The fixture is classified ordinary apparatus ; its protection grade against penetration by external agents,solid or liquid, is IP 20.
2. General information
1. Packaging and transportation
6
English

2.2. Warranty conditions
1. The fixture is guaranteed for a period of 12 months from the date of purchase against manufacturing or materials defects.
2. The warranty does not extend to damage caused by inappropriate usage or use by inexperienced operators.
3. The warranty is immediately void if the projector has been operated or dismantled by unauthorised personnel.
4. The warranty does not extend to fixture replacement.
5. The serial number of the projector is required for any advice or service fro your authorised Coemar service centre.
2.3. CE norms
The projector meets or exceeds all applicable CE requirements.
3.1. Technical characteristics
Power: 200/208/230/240 Vac 50/60Hz
Nominal current: 8A
Maximum current: 10A
Power factor: cos ϕ= 0,9
Lamp wattage: 1200W MH
Maximum ambient temperature: 35°C / 95° F
Weight: 45.5 Kg / 100.1 Lbs
IP rating: IP20
3.2. Dimensions
3.3. Components
Component description
A. Body housing
B. Zoom effect group
C. Color wheel group
D. Colors changer group
E. Reflector group
F. Yoke
G. Base housing
H. Base
A
B
C
D
E
F
G
H
591.6mm
22.11”
801.5mm
31.55”
509.7mm
20.07”
580.7mm
22.86”
492.6mm
19.39”
163.4mm
6.43”
30mm
1.18”
304.8mm
12”
304.8mm
12”
535.4mm
21.08”
269.6mm
10.61”
292mm
11.50”
304.8mm
12”
3. Product specifications
7
English

4.1. Mechanical installation
Infinity Wash XL may be either floor or ceiling mounted. For floor mounting, the unit is provided with four rubber mounting feet.
For ceiling mounted installations, Coemar includes two cam-lock (A) support brackets.
The two cam-lock brackets may be mounted in 3 different positions (B,Cand D) on the base of the Infinity Wash XL. The cam-lock
brackets are affixed via a 1/4 nut. Please ensure that they are correctly seated and firmly tightened into position.
For ceiling mounted installations we suggest the use of appropriate clamps or fixings to attach the fixture to the mounting surface. Clamps
may be attached to the central hole provided in the cam-lock brackets, as shown in the following diagram.
The structure from which the unit is hung should be of sufficient rating to hold the weight of the unit, as should any clamps used to hang
the unit. The structure should also be sufficiently rigid so as not to move or shake whilst the projector moves during its operation.
Do not install the projector in locations where it is readily accessible by aunthorised or untrained personnel.
4.2. Safety connections
If the Infinity Wash XL is affixed to a structure the use of a safety chain designed to meet relevant safety standards is recommended. You
may attach the safety chain to the holes “E” located on the base of the fixture and to the structure itself.
If using an after-market safety chain not manufactured by Coemar, ensure that it is of sufficient rating to hold the weight of the unit.
E
ATTENTION!!
Ensure that the structure from which the unit is hung is of sufficient rating to hold the weight of the unit,
as are any clamps, nuts and bolts used to hang the unit.
A
304.8mm
12”
304.8mm
12”
304.8mm
12”
BCD
4. Installation
8
English

5.1. Operating voltage and frequency
The projector may operate at voltages of 200, 208, 230 or 240VAC at a frequency of 50 or 60Hz. Coemar presets (barring specific
requests) a voltage of 230v at a frequency of 50Hz.. The preset voltage is indicated on the base of the projector.
Infinity Wash XL will automatically adjust its operation to suit a frequency of 50Hz or 60Hz.
5.2. Altering the operating voltage (Reserved for technical personnel only)
If the factory preset operating voltage do not correspond to those in use in your country of operation, you may alter the settings as descri-
bed in the following paragraphs.
1. Loosen the screws “A” on the cover of the base of the unit, as shown in
the diagram below, using an appropriate screwdriver, thereby removing
the cover completely and allowing access to the internal components of
the base of the Infinity Wash XL.
2. Locate the main selector in the base of the unit.
3. Select a voltage from amongst 200, 208, 230 or 240V by moving the
selector to the correct voltage.
4. When you have made changes, note these on the outside of the
Infinity Wash XL.
5. Replace and fasten all the housings as per their original positions.
ATTENTION!!
Incorrect selection of operating voltage will seriously compromise the
functioning of the projector and will immediately void the warranty.
5. Powering up
9
English

5.3. Mains connection
Mains cable characteristics
The mains cable provided is thermally resistant, complying to the most recent international standards. It meets or exceeds VDE and IEC norms, IEC
331,IEC 332 3C,CEI 20 35.
NB: In case of cable replacement, similar cable with comparable thermal resistant qualities must be used exclusively (cable 3x1.5 ø external
10 mm, rated 300/500V, tested to 2KV, operating temperature -40° +180°, Coemar cod. CV5309).
Connecting to mains power
For connection purposes, ensure your plug is of a suitable rating to sustain the maximum current:
•200/208/230/240Vac 4.5 amps constant current in normal operation
Locate the mains cable which exits the base of the unit and connect as shown below:
ATTENTION!!
• The use of a thermal magnetic circuit breaker is recommended for each projector. Strict adherance to all regulatory
norms is higly recommended.
• Infinity Wash XL should never be supplied mains power via a Dimmer; this is potentially dangerous.
• Prior to powering up the projector, ensure that the model in your possession correctly mathces the mains supply avai-
lable to you.
• A good earth connection is essential for the correct operation of the Infinity Wash XL. Never connect the projector to
main power if the green/yellow earth cable is not correctly connected
• All cable and plug connections should be carried out by fully qualified and licenced personnel only.
ground
neutral
live
brown
blue
yellow/green
main
10
English

Control signal is digital and is transmitted via two pair screened ø0.5mm cable as per international standards for the transmission of
DMX512 data. Connection is serial, utilising XLR3 and XLR5, male and female sockets located on the base of the Infinity Wash XL, labe-
led DMX 512 IN and OUT (see diagram).
Plug/socket connections for XLR3 and XLR5 connectors:
Pin connections conform to the international standard as per the following table:
pin 1 = GND
pin 2 = data -
pin 3 = data +
If using a controller which output signal via an XLR 5 (5 pin) socket, do not use pins 4 and 5, leave them unconnected.
ATTENTION!!
Ensure that all data conductors are isolated from one another and the metal housing of the connector.
Pin number 1 should never be connected to the device’s power supply.
3
2
1
Controller
Standard
DMX 512
OUT
out
in
Ad altri Infinty Wash XL
Connect to other Infinty Wash XL
out
in
6. DMX signal connection
11
English

After having followed the preceding steps, turn on the projector via the main Power switch.
The display and will show in sequnece the software version installed in the 3 onboard microprocessors - the display “D”and the two
master “A” and “B”.
For example, upon turning on power, the Infinity Wash XL may show:
D1.02 (display pcb “D” software version)
A1.03 (master pcb “A” software version)
B 1.00 (master pdb “B” software version)
The projector will perform a reset function on all the internal and external motors. This will last some few seconds, after which it will be
subject to the external signal from the controller. The display will remain fixed on indicating correct DMX 512 signal reception.
If the display flashed, there is no DMX signal being received. Check your cabling and your controller.
7.1. DMX addressing
Each projector utilises 22 channels of DMX 512 for complete control (for further information, see section 7.2. DMX functions).
DMX addresses
To ensure that each projector accesses the correct signal, it is necessary to correctly address each fixture. This procedure must be carried
out on every projector being used. When powered up initially, each projector will show A001 which indicates DMX address 001; a
projector thus addressed will respond to commands on channel 1to 22 from your DMX controller. A second unit should be address-
es as A023, a third as A045 and so on until the final projector has been addressed.
Altering DMX addresses
1. Press the +or -buttons until the display shows the required DMX address. The characters in the display will flash to indicate that the
selection is not yet stored in memory.
2. Press the enter button to confirm your selection. The display panel will cease to flash and the projector will now respond to the new
DMX 512 address.
Important Note: holding down the +or -buttons will cause the display to alter at an increased speed, allowing a faster selection to be made.
ATTENTION!!
If you alter the DMX with no DMX controller connected, the characters in the display panel will continue to flash
even after you have pressed the ENTER button.
m
e
n
u
m
e
n
u
e
n
t
e
r
e
n
t
e
r
+
+
AOO1
7. Turning on the projector
12
English

7.2. DMX functions
1
Xaxis,basemovement
(pan)coarse
proportional proportionalcoarsecontrolofthebasemotormovement 0 - 255 0% - 100%
2
Xaxis,basemovement
(pan) fine
proportional proportionalfinecontrolofthebasemotormovement 0 - 255 0% - 100%
3
Yaxis,yokemovement
(tilt) coarse
proportional proportionalcoarsecontroloftheyokemotormovement 0 - 255 0% - 100%
4Yaxis,yokemovement
(tilt) fine proportional proportionalfinecontroloftheyokemotormovement 0 - 255 0% - 100%
step standard(fast)
0-9 0%-4%
step
ultrafastmovement(bestforprogrammingpositions) 10 - 25 4% - 10%
proportional vector mode (from fast to slow)
26 - 127 10% - 50%
proportional trackingmode (from fast to slow)
128 - 247 50% - 97%
step tracking mode (slow)
248 - 255 97% - 100%
6dimmer proportional gradualadjustmentofluminousintensityfrom0to100% 0 - 255 0% - 100%
step shutterclosed(zapoff) 0-9 0%-4%
proportional strobeeffectwith variablespeed fromslow tofast 10 - 66 4% - 26%
step shutteropen(zapoff) 67 - 68 26% - 27%
proportional sequencedpulseeffect,slowclosing,fastopening(withvariablespeedfromslowtofast) 69 - 125 27% - 49%
step shutteropen(zapoff) 126 - 127 49% - 50%
proportional sequencedpulseeffect,fastclosing,slowopening(withvariablespeedfromfasttoslow) 128 - 184 50% - 72%
step shutteropen(zapoff) 185 - 187 73% - 73%
proportional randomstrobeeffect,non-synchronised,variablespeedfromslowtofast 188 - 244 74% - 96%
step shutteropen(zapoff) 245 - 255 96% - 100%
8zoom effect proportional proportionalcontrol ofzoom effect wheelfrom narrowtowide beam(from 6°to13°) 0 - 255 0% - 100%
9zoom proportional proportional control ofzoomfrom narrow towidebeam (from 6°to80°) 0 - 255 0% - 100%
step noeffect 0-9 0%-4%
proportional zoomshakeeffectwithvariable speedfrom slowto fast 10 - 71 4% - 28%
proportional zoomshakesequencedpulseeffect,slowclosing,fastopening
(withvariablespeed from slow to fast) 72 - 133 28% - 52%
proportional zoomshakesequencedpulseeffect,fastclosing,slowopening
(withvariablespeed from fast to slow) 134 - 195 53% - 76%
proportional zoomshakerandomstrobeeffect,non-synchronised,variablespeedfromslowtofast 196 - 255 77% - 100%
noeffect 0-9 0%-4%
effect1 10 - 39 4%-15%
effect2 40 - 69 16% - 27%
effect3 70 - 99 27% - 39%
effect4 100 - 128 39% - 50%
shakeeffect 4 (variableadjustmentof oscillation anglefrom minimum tomaximum) 129 - 160 51% - 63%
shakeeffect 3 (variableadjustmentof oscillation anglefrom minimum tomaximum) 161 - 192 63% - 75%
shakeeffect 2 (variableadjustmentof oscillation anglefrom minimum tomaximum) 193 - 224 76% - 88%
shakeeffect 1 (variableadjustmentof oscillation anglefrom minimum tomaximum) 225 - 255 88% - 100%
step noeffect 0-9 0%-4%
proportional proportionalindexingoftheeffectthrough360° 10 - 128 4% - 50%
proportional
continuousrotationoftheeffectinacounter-clockwisedirectionwith
proportionalcontroloverdecreasingspeed
129 - 188 51% - 74%
step stopeffectrotation 189 - 193 74% - 76%
proportional continuousrotationoftheeffectinaclockwisedirectionwith
proportionalcontroloverincreasingspeed 194 - 255 76% - 100%
selectingeffectswheel
+
shakemovement
11
indexing effect rotation
through 360°
step
proportional
dmx
channel
percentage
function
type of control
effect
decimal
5
12
movementspeed
shutter, strobe
and zap effect
7
zoomshake
10
13
English

nocolour,whitebeam 0-5 0%-2%
color1 6-14 2%-5%
color2 15 - 22 6% - 9%
color3 23 - 30 9%-12%
color4 31 - 38 12% - 15%
color5 39 - 45 15% - 18%
fromcolor5tocolour1,proportional positioning 46 - 127 18% - 50%
rainboweffect fromfast to slowin ananticlockwisedirection 128 - 190 50% - 75%
rainboweffect from slow to fastina clockwise direction 191 - 255 75% - 100%
14 cyan proportional proportionalcontrolofthepercentageofcyancolorinthelightbeamfrom0to100% 0 - 255 0% - 100%
15 cyancolor saturation proportional saturation adjustmentofcyan color tonality;frombright todark 0 - 255 0% - 100%
16 magenta proportional proportionalcontrolofthepercentageofmagentacolorinthelightbeamfrom0to100% 0 - 255 0% - 100%
17 magentacolor saturation proportional saturationadjustmentofmagentacolortonality;frombrighttodark 0 - 255 0% - 100%
18 yellow proportional proportionalcontrolofthepercentageofyellowcolorinthelightbeamfrom 0to100% 0 - 255 0% - 100%
19 CTO proportional proportionalcontrolofthepercentageofCTOinthelightbeamfrom6300°Kto3200°K 0 - 255 0% - 100%
noeffect
0-10 0%-4%
zapeffectsynchronisedwiththestrobeeffect,speedandmodeselectedbystrobechannel7 11 - 30 4% - 12%
zapeffect,flickerandspeedadjustable,speedandmodeselectedbystrobechannel7 31 - 249 12% - 98%
black-outofthelightbeamduringPAN/TILTmovement,colorswheelandeffectswheel 250 - 255 98% - 100%
21
lamp power control in
conjunction with channel 22
proportional
lamp power adjustment from minimum to maximum (800W - 1400W)
whenchannel22isbetween171-195dmx
0-255 0% - 100%
park,nofunction 0-9 0%-4%
lampoff 10 - 29 4%-11%
panandtiltreset(onceonly) 30 - 65 12% - 25%
allmotor reset exeptdimmer, pan andtilt(once only) 66 - 100 26% - 39%
allmotorresetexeptdimmer (once only) 101 - 135 40% - 53%
resetof all themotors (once only) 136 - 170 53% - 67%
lampon,enabledpoweradjustmentfrom800W to1400W 171 - 195 67% - 76%
lampon,maximum power 171 - 255 67% - 100%
dmx
channel
percentage
function
type of control
effect
decimal
20
Note 1: the display panel may be used to disable the switching off of the lamp via DMX
Note 2: turning off the lamp and all reset functions are delayed by 6 seconds to prevent accidental activation
Note 3: the lamp on/off function can only be effected if an opposite level is set
lamp on/off and
motorsreset
22
step
zap effect
(effectvariesdependingupon
channel7strobe)
step
13
step
proportional
selecting colors from the color
wheel
14
English

The display panel of the Infinity Wash XL shows all the functions available; it is possible to change some of those parameters and to
add some functions.
Changing the preset settings made by Coemar can vary the functions of the device so that it may not respond to a DMX 512 controller
being used to control it. Carefully follow the instructions before applying any variations or selections.
NOTE: the symbol ☞shows which key has to be pushed to obtain the desired function .
8.1. Quick guide to menu navigation
For your convenience, the following is a guide to navigating the menu system of the projector.
F U NC
☞
enter
MEAS
☞
enter
PDIR
☞
+o–
TDIR
☞
+o–
OPTO
☞
+o–
FANS
☞
+o–
DISP
☞
+o–
LED
☞
+o–
RESE
☞
+o–
OFSE
☞
+o–
DEMO
☞
+o–
X.Y
☞
+o–
PAN
☞
+o–
ID
☞
+o–
TEMP
☞
+o–
V.FAN
☞
+o–
DMIN
☞
+o–
RATE
☞
+o–
ALRM
☞
+o–
HOUR
☞
+o–
AOO1
☞
menu
TEST
☞
+o–
A023
new DMX address
☞
+o–A023 DMX address ☞
enter
☞
+o–
LAMP
☞
+o–
LAMP
☞
+o–
ZAP.E
☞
+o–
Press together enter and menu keys
for 10 seconds: the display will show
alignement functions menu
8. Display panel functions
15
English

8.2. Measure and test (MEAS)
The internal microprocessor of the Infinity Wash XL allows for several diagnostic and output parameters to be
displayed. You may record, in this menu, determine the position in which the projector will come to rest when turned on with no dmx
signal attached.
☞
menu
AOO1
☞
enter
V.FAN voltage to fans
to measure the DC voltage to the fans located in the unit.
Values higher than 25,8V are anomalous.
25.2V
v oltage measurement
☞
enter
CH01
from channel
CH22
to channel
10
DMX value
255
DMX value
☞
enter
☞
+o–
DMIN DMX value on each channel
reading of DMX value (0/255), received by each
of the 16 channels on DMX 512 line.
☞
enter ☞
enter
RATE DMX rate
reading of DMX 512 signal value. ☞
enter 22
value reading
NDMX
no dmx signal
NO.AL
no alarm message
ALRM alarm
Reading of Warning message
sequences (errors) shown during reset
operation
☞
enter
☞
+o–O PER
alarm message
58C
temperature measurement
TEMP temperature
to measure the internal temperature in °C☞
enter
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
10
value reading
☞
+o–
☞
enter
☞
enter
☞
enter
☞
+o–
HOUR working time
working time (in hours)
589
value reading
1230
value reading
LIFE
lamp life after last reset
LIFS
life of all lamps
used on the unit
UNIT
projector life
☞
enter
N.B.: reset the LIFE value when
changing the lamp
1400
reading lamp power
LAMP lamp status
Reading lamp status ☞
enter
☞
+o–OFF
lamp off
☞
+o–
☞
enter 0128
☞
enter
☞
enter ☞
+o–
PAN
pan movement ☞
enter
es. 0150
☞
enter 0128
☞
enter
☞
enter ☞
+o–
TILT
tilt movement ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
DIMM
dimmer activation ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
SHUT
shutter activation ☞
enter
es.
☞
enter SURE
☞
enter
☞
enter STOR
to record the position of the unit and of its internal
components. If DMX signal is not applied, the recorded
setting will appear at the end of reset operation when
the unit is switched on.
☞
enter
☞
enter ☞
enter
☞
enter ☞
+o–
ZOM.E
effect zoom activation ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
ZOOM
zoom activation ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
EF.RT
effect rotation activation ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
COLR
color wheel selection ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
CYAN
cyan activation ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
MAGE
magenta activation ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
YELL
yellow activation ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
CONV
conversion filter activation ☞
enter
es.
☞
enter ☞
enter
☞
enter ☞
+o–
ZAP.E
zap effect activation ☞
enter
es.
0128
0128
0128
0128
0128
0128
0128
0128
0128
0128
0128
0150
0150
0150
0150
0150
0150
0150
0150
0150
0150
0150
0150
☞
enter ☞
enter
☞
enter ☞
+o–
SAT.C
saturation cyan activation ☞
enter
es.
0128 0150
☞
enter ☞
enter
☞
enter ☞
+o–
SAT.M
saturation magenta activation ☞
enter
es.
0128 0150
TEST test
function test
MEAS
☞
enter ☞
enter
☞
enter ☞
+o–
EFCT
effect wheel activation ☞
enter
es.
0128 0150
16
English

8.3. Function settings (FUNC)
The projector allows the altering of several functions and for selecting personalised settings.
8.4. Rapid scrolling
Via the Infinity Wash XL display it is possible to rapidly scroll through the various numbers displayed in the menu in the following manner:
1. Pressing the +or -buttons will cause the number to scroll more quickly.
2. Pressing and holding the +button and then the -button will cause the numbers to jump to the highest value.
3. Pressing and holding the -button and then the +button will cause the numbers to jump to the lowest value.
☞
menu
AOO1
-– -– -– -–
reset activation
CW
clockwise
CCW
Counter-clockwise
CW
clockwise
CCW
Counter-clockwise
ON
sensor activation
OFF
sensor deactivation
☞
+o–
☞
+o–
☞
enter
☞
enter
☞
enter
☞
enter
☞
+o–
☞
+o–
☞
enter
☞
enter
☞
+o–
☞
+o–
STRD
fan speed control
ON
fan always on ☞
enter
☞
enter
☞
+o–
☞
+o–
AA
base downwards
base upwards ☞
enter
☞
enter
☞
+o–
☞
+o–
AA
☞
enter
☞
enter
☞
enter
☞
enter
☞
enter
☞
enter
OFSE default function setting
To set all the functions at the original values, but for the
alignement operations.
SURE
☞
enter
PAN pan control
reduce rotation angle from 530°to 400°.
5 4 0
pan 540°
400
pan 400°☞
enter
☞
enter
☞
+o–
☞
+o–
☞
enter
O N
Pan/Tilt active
OFF
Pan/Tilt inactive ☞
enter
☞
enter
☞
+o–
☞
+o–
☞
enter
ON
display actived
AUTO
display switch off after 6 second ☞
enter
☞
enter
☞
+o–
☞
+o–
☞
enter
☞
enter
IDID number setting
To set the unit’s ID number from 0 (no ID, to 250)
1--250
numeric value
☞
+o–
☞
+o–X.Y Pan e Tilt setting
Function without pan/tilt
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
☞
+o–
DEMO
(flashing)
demo program activation
PDIR pan movement inversion
To reverse horizontal movement direction of the beam
on DMX level variation.
TDIR tilt an movement inversion
To reverse vertical movement direction of the beam on
DMX level variation.
OPTO optic sensor de-activation
To deactivate the optic sensor function with return inpo-
sition of the unit if accidentally knocked out of the place.
STRD
switching on through DMX 512
ON
lamp always on ☞
enter
☞
enter
☞
+o–
☞
+o–
☞
enter
☞
+o–LAMP Lamp control
To disable on/off control of the lamp by DMX signal.
FANS fans control
Fan status control through PCB (Strd) or fans always on
(On).
DISP reverse display
To reverse the display reading depending on mounting
position (base or suspended).
LED display control
To disable display visualisation.
RESE reset
Reset function
DEMO demo program
To see all the unit function
O N
zap on
OFF
zap off ☞
enter
☞
enter
☞
+o–
☞
+o–
☞
enter
ZAP.Ezap effect
Zap effect
☞
+o–
☞
enter
☞
+o–
☞
enter
☞
enter
FUNC
17
English

8.5.Connecting the DR1
All the functions available via the display menu are also available via the DR1 (cod. 9703).
The DR1 is a remote device designed for technical users who need to perform tasks on the projectors whilst they may be located in inac-
cessible positions. It acts as a remote control.
For example, the DR1 eliminates the need for climbing up truss structures to gain direct physical access to the projector to alter such
parameters as DMX address, reading outputs such as lamp life as well as all other functions available via the digital display unit on the
projector.
In order to utilise the DR1 remote device, you must first activate the identifying number of the projector ID, which must be unique in
the particular DMX universe in which it is currently installed.
The method for setting an identification number ID is shown below.
For further information, consult the DR1 instruction manual.
8.6. Turning on the projector with no articulated movement
This function may be useful should you need to power up the Infinity Wash XL whilst it is in its flight case or to re-address it or alter
any parameters and you wish to in the absence of any articulated movement.
1. Turn on the projector whilst holding down the enter, menu and – buttons
The The projector will proceed with a reset of all its motors with the exception of those which control articulated movement, the pan
and tilt motors, which remain static.
2. You may alter the DMX address or any other parameter without any articulated movement occuring
3. To return to normal functioning of the Infinity Wash XL simply turn the projector off and on via the Power switch or activate the
Reset function.
8.7. Resetting the counter
The lamp life counter needs to be reset to zero at every lamp change to provide accurate information on lamp life.
When turning on the Infinity Wash XL , simultaneously hold down the +and – buttons. The projector will restart with its counter
reset.
The projector has reset the LIFE counter.
To verify that this operation has occured:
1. Press the menu button and then press enter.
2. Press the +or -buttons until MEAS is displayed, then press enter.
3. Press the +or -buttons until HOUR (hours) is displayed, then press enter.
4. Press the +or -buttons until LIFE (lamp life) is displayed, then press enter.
5. If the display shows 0000, the counter has been reset.
N.B. You may also wish to verify that other electronic counters such as LIFS (total lamp operating lives) and UNIT (total proejctor ope-
rating life) have remained unaltered.
m
e
n
u
m
e
n
u
e
n
t
e
r
e
n
t
e
r
+
+
m
e
n
u
m
e
n
u
e
n
t
e
r
e
n
t
e
r
+
+
☞
menu
AOO1
FUNC
ID ID number setting
To set the unit’s ID number from 0(no ID, to 250).
1--250
numeric value
☞
+o–
☞
enter
☞
+o–
☞
enter
☞
enter
ATTENTION!!
• If you set a projectors identification number to “0” it will not be able to communicate with the DR1.
• Never assign the same ID to two or more projectors. This may jeapordise the functioning of the entire system.
(The DR1 will show an error message).
18
English

The Infinity WashXL utilises the Philips MSR GOLD 1200 SA/SE FastFit with PGJ50 base lamps. The use power is 1400W.
These lamps are available via your Coemar distributor or service centre.
The fixture’s internal temperature can reach 250° C after 5 minutes, with a maximum peak of 450° C; ensure that the lamp is cold prior
to attempting removal. The fixture should be allowed to stand and cool for 10 minutes prior to its removal.
The lamps are part of the mercury vapour family of discharge lamps and must be handled with great care. The lamp operates at high
pressure, and the slight risk of explosion of the lamp exists if operated over its recommended life. We recommend, therefore, that the
lamp be replaced within the manufacturer’s specified lamp life.
9.1. Lamp installation
1. Use a suitable tool to loosen the four screws “A“ which affix the lampholder cover at the rear of the projector.
2. Remove the lampholder cover “B”. 3. Identify the lampholder “C“.
ATTENTION!!
Disconnet the unit from mains power prior to attempting lamp installation or replacement
Make sure the projector is sufficiently cooled.
Lamp Philips MSR GOLD 1200 SA/SE FastFit
Coemar code 105817
Wattage Range 800 - 1400W
Lumen output at 1200W 95.000 lm
Colour temperature 6300° K
Base PGJ50
Approximate lamp life 750 hours
9. Lamp installation and alignment
19
English

4. Insert the lamp and rotate clockwise.
The lamp used is manufactured from quartz glass and should be handled with care; always adhere to the instructions supplied in the
lamp’s packaging. Never touch the glass directly, use the tissue provided in the lamp’s packaging. DO NOT USE UNDUE FORCE.
5. Replace the lampholder cover in its original position and refasten the two screws “A” which were previously removed.
9.2. Aligning the lamp in the optical path
Aligning the lamp in the optical system is achieved via the 3 adjusters at the rear of the projector. This procedure should be undertaken
to maximise output, properly align the lamp in the optical system and to avoid the possible overheating of the internal components due
to the incorrect focusing of the beam onto components not intended to be exposed to this.
Alignment procedure
Alignment is effected by the 3 adjusters A, Band Clocated on the lampholder assembly. The lamp should be on, black-out and dimmer
fully open, and no colours selected. If the lamp is not correctly aligned, a hot-spot will be readily noticeable. Using the 3 adjusters in uni-
son, you will need to bring the hot-spot to the centre of the beam and then flatten the beam to maximum uniformity.
ATTENTION!!
Each time you change the lamp, we recommend the following be carried out:
• realign the lamp in the optical path to avoid overheating dichroics and/or effects.
• reset the lamp life counter (as described in section 8.7. Resetting the counter).
20
English