Cognex MX-1000 User manual

MX-1000
Quick Reference Guide
09/08/2017
Version:5.7.1.51

Precautions
Observe these precautions when installing the Cognex product, to reduce the risk of
injury or equipment damage:
lTo reduce the risk of damage or malfunction due to over-voltage, line noise,
electrostatic discharge (ESD), power surges, or other irregularities in the
power supply, route all cables and wires away from high-voltage power
sources.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lCable shielding can be degraded or cables can be damaged or wear out
more quickly if a service loop or bend radius is tighter than 10X the cable
diameter. The bend radius must begin at least six inches from the
connector.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purpose only and may be changed
without notice.
2

MX-1000 Layout
1 Scanner head (rotatable by 45°)
2 Indicator LEDs
3 Side trigger buttons
4 Power button
5 Touch screen
6 Home button
7 Speaker vents
8 Recessed area for mobile camera
9 Slider to lock battery cover
10 Battery cover
11 Lanyard hook
12 End cap of pistol grip*
13 Trigger button on the pistol grip*
*Pistol grip is optional
3

MX-1000 Accessories
Battery for reader (DMA-MTBATTERY-01)
Battery for pistol grip accessory (3070 mAh, DMA-HHBATTERY-01)
Pistol grip (DMA-GRIP-01)
Note: The grip features its own trigger button and an additional battery
which can be charged via the charging station.
Belt holster (DMA-HOLSTER-01, and DMA-HOLSTER-02)
Wireless charging station (DMA-MTBASE-xx*)
Multi-device charger (DMA-MTBASE4-US, DMA-MTBASE4-EU, DMA-
MTBASE4BKT-US, DMA-MTBASE4BKT-EU)
Multi-battery charger (DMA-MBC-xx)
Wireless car charger (DMA-VMCHARGER-00)
Power supply for charging station 24V/18W (DMA-24VPWR-xx*)
4

USB Type-C battery charger kits:
lDMA-MXUSB-01: USB Type-C Battery Cover (DMA-MXUSB-00)
+ USB Type-C 3Amp Car Charger (DMA-MXUSB-CHARGER)
lDMA-MXUSB-02: USB Type-C Battery Cover (DMA-MXUSB-00)
+ Handstrap (DMA-MXSTRAP-00)
lDMA-MXUSB-03: USB Type-C Battery Cover (DMA-MXUSB-00)
+ USB Type-C 3Amp Car Charger (DMA-MXUSB-CHARGER) +
Handstrap (DMA-MXSTRAP-00)
Passive car holder (DMA-VMHOLDER-00)
Note: Using or storing the device outside of the recommended
temperature ranges may damage or reduce the battery’s lifespan.
Leaving the MX Series Mobile Terminal with a mobile device in direct
sunlight for an extended amount of time can raise the temperature above
the recommended limit.
Top Cover (DMA-COVERKIT-S6, DMA-COVERKIT-S7)
* xx can be US or EU
5

Dimensional Drawings
6

Field of View and Reading Distances
Note: Due to tolerances, ranges can vary by +/- 5 mm for small codes to +/- a couple of centimeters for
large codes.
7

Assembling the Reader
Note: For details, see the MX-1000 Reference Manual.
For a list of supported mobile devices, please contact Cognex.
8

Installation
Installation procedures and specifications are presented in detail in the MX-
1000Reference Manual, which is installed with the DataMan Setup Tool. From the
Windows Start menu, select the following to access the manual: All Programs >
Cognex > DataMan Software v5.7.0 > Documentation.
Note: If any of the standard components appear to be missing or damaged,
immediately contact your Cognex Authorized Service Provider (ASP) or
Cognex Technical Support.
CAUTION:All cable connectors are “keyed” to fit the connectors on the
reader; do not force the connections or damage may occur.
Install Software and Documentation and
Connect the Reader
To configure an MX-1000 reader, the DataMan Setup Tool software must be
installed on a networked PC. The DataMan Setup Tool is available from the
DataMan support site: http://www.cognex.com/support/dataman.
Note: The DataMan Setup Tool only works if the DataMan Quick Setup is
installed on the mobile device. For further details, see the MX-1000 User
Guide.
1. After installing the software, connect the MX-1000 to your PC.
2. Launch the DataMan Setup Tool and click Refresh.
3. Select your MX-1000 reader from the list and click Connect.
9

MX-1000 Specifications
Weight 510 g (675 g with pistol grip)
Charging Temperature
Operating Temperature
0ºC — +35ºC (+32ºF — +95ºF)
0ºC — +40ºC (+32ºF — +104ºF)
Storage Temperature -40ºC — +60ºC (-40ºF — +140ºF)
Maximum Humidity < 95% (non-condensing)
Environmental IP65
Codes 1-D: UPC/EAN/JAN, Codabar, Interleaved 2 of 5, Code 39, Code 128, Code 93,
Pharmacode, GS1 DataBar, PDF417, Micro PDF417
2-D: Data Matrix, QR Code, and MicroQR Code, DotCode* and postal code*
Power Supply Requirements Battery power
Expected operating time for
typical scan batches (400 scan
per hour) with a fully charged
battery
12 hours
*MX-1000X only
Imager Specifications
Specification MX-1000 Imager
Image Sensor 1/3 inch CMOS
Image Sensor Properties 6.0 μm square pixels
Image Resolution (Pixels) 752 x 480 global shutter sensor
Lens Type 3 focal position 6.2 mm, M12 lens with IR blocking filter
10