Cole & Bright Security 63729 User manual
Brunnings Import Export Pty Limited
3/19-23 Clarinda Road,
Oakleigh South VIC 3167
63729
CARE AND MAINTENANCE
• From time to time, ensure the plug between the solar panel and light is
• From time to time, ensure the plug between the solar panel and light is
securely connected.
securely connected.
• It is advised to adjust the angle of the solar panel to optimise the exposure
• It is advised to adjust the angle of the solar panel to optimise the exposure
to the sun during the winter months.
to the sun during the winter months.
• The solar panel and the lens should be cleaned with a damp cotton cloth
• The solar panel and the lens should be cleaned with a damp cotton cloth
on a regular basis to ensure optimal performance. Periodically, utilise the
on a regular basis to ensure optimal performance. Periodically, utilise the
same technique to clean the lens of the motion light.
same technique to clean the lens of the motion light.
• Never let any abrasive material come into contact with the solar panel.
• Never let any abrasive material come into contact with the solar panel.
For recycling and disposal of batteries to protect the environment, please check the
internet or your local phone directory for local recycling centres and/or follow local
government regulations.
TROUBLESHOOTING
PROBLEM
Light will not come on.
Light will not come on.
POSSIBLE CAUSES
•
•
Solar panel not positioned in direct sunlight.
Solar panel not positioned in direct sunlight.
•
•
Battery pack not fully charged.
Battery pack not fully charged.
•
•
Solar panel no longer as bright.
Solar panel no longer as bright.
SOLUTION
•
•
Reposition the solar panel.
Reposition the solar panel.
•
•
Recharge the battery pack
Recharge the battery pack
•
•
Sun exposure may fluctuate as the season change.
Sun exposure may fluctuate as the season change.
Reposition the light or replace the battery pack.
Reposition the light or replace the battery pack.
If you are doing any of the following go to the
locations below for detailed instructions -
LINKING 3 OR MORE LIGHTS (FOR THE FIRST TIME)
LINKING 3 OR MORE LIGHTS (FOR THE FIRST TIME)
ADDING A NEW LIGHT(S) TO THE LINKED NETWORK
ADDING A NEW LIGHT(S) TO THE LINKED NETWORK
ADDING A NEW LIGHT(S) TO THE LINKED NETWORK
ADDING A NEW LIGHT(S) TO THE LINKED NETWORK
(but you can’t find the Original Master Light)
(but you can’t find the Original Master Light)
• Our website link: www.brunnings.com.au
• Our website link: www.brunnings.com.au
• Scan the QR code on the right
• Scan the QR code on the right
• Go to our How To Videos:
• Go to our How To Videos:
www.youtube.com/Radar360linkable
www.youtube.com/Radar360linkable
IMPORTANT INFORMATION
• Keep these instructions safe for future reference.
• Your motion light and solar panel are both weatherproof.
• You can mount your motion light indoors, but your solar panel must be
installed outdoors to receive light from the sun.
• If using a step ladder, you may require a second person to help install
the solar motion light.
• Prior to installation, lay out all the components and check the part list
section in this manual.
• Never look directly into the solar motion light when illuminated.
• If you locate your light in the vicinity of windows or glass doors,
movement may trigger the sensor to turn the lights on. Locate your lights
with this in mind.
IMPORTANT: READ ALL SAFETY INFORMATION AND INSTALLATION
IMPORTANT: READ ALL SAFETY INFORMATION AND INSTALLATION
INSTRUCTIONS BEFORE INSTALLING OR SERVICING THIS PRODUCT.
INSTRUCTIONS BEFORE INSTALLING OR SERVICING THIS PRODUCT.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
SOLAR POWERED + LINKABLE
MAXIMA SECURITY LIGHT
Customer Helpline: 03 9543 5600
SCAN HERE
FOR MORE
INFORMATION
PO
RTANT INF
O
RMATI
O
N
eep these instructions safe for future reference
MAXIMA SECURITY
LIGHMAXIMA SECURITY LIGH
360°
with
with
LINKABLE
63729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 163729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 1 21/08/2023 11:19:26 AM21/08/2023 11:19:26 AM
Introducing
Radar 360° + LINKABLE is the new next-generation solar sensor light from Cole
& Bright. The new “LINKABLE” technology turns a single security light into a
potential chain of security lights.
Radar 360° + LINKABLE requires no wires, hardware, or additional components
- just another Radar 360° + LINKABLE light in the vicinity.
Radar 360° + LINKABLE lights do not have to be the same. The technology
spans the Radar 360° + LINKABLE range, allowing youto connect a post light
to a wall-mounted light or an inground spotlight to a post light, helping to
create a well-lit, secure and safer environment around the home.
Any solar light can be a security light with Cole and Bright.
The Maxima+ Solar Security Light has an ULTRA BRIGHT mode because it is
a spotlight. Other LINKABLE lights in the RADAR 360˚Linkable Range may
also have an AMBIENCE mode.
RADAR 360˚+ Linkable lights require no mains wiring - the solar light is
charged by energy from the sun.
Easy to use SMART CONTROL FUNCTION allows you to link multiple
Radar 360˚lights to create a network of multiple lights that illuminate
the perimeter around your home when triggered.
ULTRA BRIGHT
SENSOR MODE
MAXIMUM ENERGY SAVING
SMART CONTROL FUNCTION
2 7
approx.7 m
approx. 5 m
360°
LINKABLE
63729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 263729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 2 21/08/2023 11:19:32 AM21/08/2023 11:19:32 AM
OPERATING INSTRUCTIONS
CHARGING YOUR RADAR 360˚LIGHTS
FOR THE FIRST TIME
1. Find a location where your light is exposed to full sunlight for at least 8
hours. This will typically require a full day so start charging in the morning.
2. Turn your light switch to the “M”
position for charging to commence.
3. After charging is complete or it is getting
dark, turn your switch to OFF until you are
ready to start the LINK process. This
prevents the battery from running down
again, if there is a delay between charging,
LINKING and installation.
The switch located on the bottom of the solar light housing is to turn on the
product and also to link your Radar 360˚linkable lights together (if you are
creating a linked network)
LINKING YOUR RADAR 360˚LIGHTS FOR THE FIRST TIME
Only TWO (2) Lights (for linking 3 or more lights, please see website)
1. Make sure your lights are fully charged before you commence
the Link procedure.
2. Take the 2 lights you wish to pair and place
the lights upwards on a level flat surface.
3. Choose one light to be a Master light.
The other light(s) will then be
Secondary light.
TOOLS REQUIRED TO INSTALL (not included)
Electric
Power Drill
Phillips
Screwdriver
Pencil Ladder Eye
Protection
Level
PARTS LIST
4
wall inserts
4
phillips screws
1
solar panel
1
light unit
GENERAL PRECAUTIONS
Keep out of reach of children.
PRE-INSTALLATION
•
•
Carefully remove the fixture from carton and check that all parts are included.
Carefully remove the fixture from carton and check that all parts are included.
Be careful not to misplace any of the parts needed for installation.
Be careful not to misplace any of the parts needed for installation.
•
•
For best results, determine light placement location before assembly. Charge
For best results, determine light placement location before assembly. Charge
the light in full sunlight for 24 hours prior to using.
the light in full sunlight for 24 hours prior to using.
INSTALLATION
Choose an ideal location.
Choose an outdoor location with full, direct sunlight
Choose an outdoor location with full, direct sunlight
so that the solar panel can receive at least 6-8 hours
so that the solar panel can receive at least 6-8 hours
of sunlight each day. Shady locations will result
of sunlight each day. Shady locations will result
in the battery receiving less energy and shorten
in the battery receiving less energy and shorten
the duration of illumination at night. The selected
the duration of illumination at night. The selected
location should not be near strong lighting sources
location should not be near strong lighting sources
such as street lights. This may cause the light to turn
such as street lights. This may cause the light to turn
off automatically as the built-in sensor detects the
off automatically as the built-in sensor detects the
nearby lighting source.
nearby lighting source.
The Maxima+ Security Light uses a highly sensitive
The Maxima+ Security Light uses a highly sensitive
motion sensor. Therefore placement position of the
motion sensor. Therefore placement position of the
light is important. For best results we recommend
light is important. For best results we recommend
you place the Maxima+ 7m away from areas where
you place the Maxima+ 7m away from areas where
it is likely to be triggered by unintended movement.
it is likely to be triggered by unintended movement.
For example, windows where there is regular
For example, windows where there is regular
movement in the house.
movement in the house. NOTE:
The Radar360˚linkable
signal can penetrate most
obstacles. The signal CANNOT
penetrate metal objects.
36
SM OFF
SM OFF
MASTER SECONDARY
63729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 363729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 3 21/08/2023 11:19:33 AM21/08/2023 11:19:33 AM
LINKING YOUR RADAR 360˚LIGHTS FOR THE FIRST TIME
Only TWO (2) Lights (con’t)
4. On the Master light move the switch located in
between the two lights to “M” position.
5. On the Secondary Light move the switch on the
base to “S” position (right).
6. Press the LINK button located on back of the light
of both units simultaneously until the lights begin to
flash. The lights will now start pairing mode. Once
the light on the Secondary unit stops flashing and
becomes a steady white light, the pairing of the 2
lights has been successful. The Master unit will still
be slowly flashing.
7. Turn the Secondary unit to OFF position. The light
should turn off.
8. Turn the Master unit to OFF position.
The light should turn off.
Your lights are now linked. When the linking process is
completed, the Radar360˚Linkable lights create a chain of
lights so that each light is set off by its nearest linked light.
9. Now turn the switch on the Secondary light to “S”
position and Master light to “M” position to begin
normal operation. Remember “M” = Master.
IF YOU WANT YOUR RADAR 360˚LIGHTS UNLINKED
Radar 360˚lights can be linked to other Radar 360˚Linkable lights
OR used unlinked on a standalone basis.
Standalone Basis
If never previously linked simply charge your light and set to
“M” or “S” position.
Unlinking your Radar 360˚Lights
1. To remove a light from the linked network
for use as a standalone, switch the light you
wish to remove to the “S” position (far right).
2. Press and hold the LINK button for more than
10 seconds.
3. Once the light changes from flashing to solid, the linked light has been
unlinked to the network.
Other linked lights will not be affected.
4. Release the LINK button.
5. Now turn OFF and back on - either to the “M” or “S” position to enable the
light to function normally.
You are now free to relocate your light to another unlinked location.
4 5
LOCATING LIGHTS IN THE NETWORK FOR BEST RESULTS
Radar360˚s has ultrasensitive sensors that detect movement at up to
7 metres in any direction from the light.
We recommend that you link your lights around 5m apart for best results.
If you locate a Radar360˚light in the vicinity of windows or glass doors,
movement indoors will likely trigger the sensors and turn the light on. This
might be a nuisance in a high traffic area.
Therefore locate your lights in a position that is unlikely to set off your
Radar360˚light from incidental movement inside your house.
SM OFF
SM OFF SM OFF
SM OFF
SM OFF
IMPORTANT – IDENTIFY YOUR MASTER LIGHT SO IT CAN BE EASILY
LOCATED IN THE FUTURE. It will be needed when adding new Radar 360˚
lights to the network in the future. Switch should be set to “M” (for Master)
position. We also suggest also tieing something bright or easy to see to the
neck between the panel & light.
10. If the link is not working as expected, simply reset your lights to factory
setting by following the “Unlinking your Radar 360˚Light” Instructions
and then start again.
63729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 463729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 4 21/08/2023 11:19:33 AM21/08/2023 11:19:33 AM
LINKING YOUR RADAR 360˚LIGHTS FOR THE FIRST TIME
Only TWO (2) Lights (con’t)
4. On the Master light move the switch located in
between the two lights to “M” position.
5. On the Secondary Light move the switch on the
base to “S” position (right).
6. Press the LINK button located on back of the light
of both units simultaneously until the lights begin to
flash. The lights will now start pairing mode. Once
the light on the Secondary unit stops flashing and
becomes a steady white light, the pairing of the 2
lights has been successful. The Master unit will still
be slowly flashing.
7. Turn the Secondary unit to OFF position. The light
should turn off.
8. Turn the Master unit to OFF position.
The light should turn off.
Your lights are now linked. When the linking process is
completed, the Radar360˚Linkable lights create a chain of
lights so that each light is set off by its nearest linked light.
9. Now turn the switch on the Secondary light to “S”
position and Master light to “M” position to begin
normal operation. Remember “M” = Master.
IF YOU WANT YOUR RADAR 360˚LIGHTS UNLINKED
Radar 360˚lights can be linked to other Radar 360˚Linkable lights
OR used unlinked on a standalone basis.
Standalone Basis
If never previously linked simply charge your light and set to
“M” or “S” position.
Unlinking your Radar 360˚Lights
1. To remove a light from the linked network
for use as a standalone, switch the light you
wish to remove to the “S” position (far right).
2. Press and hold the LINK button for more than
10 seconds.
3. Once the light changes from flashing to solid, the linked light has been
unlinked to the network.
Other linked lights will not be affected.
4. Release the LINK button.
5. Now turn OFF and back on - either to the “M” or “S” position to enable the
light to function normally.
You are now free to relocate your light to another unlinked location.
4 5
LOCATING LIGHTS IN THE NETWORK FOR BEST RESULTS
Radar360˚s has ultrasensitive sensors that detect movement at up to
7 metres in any direction from the light.
We recommend that you link your lights around 5m apart for best results.
If you locate a Radar360˚light in the vicinity of windows or glass doors,
movement indoors will likely trigger the sensors and turn the light on. This
might be a nuisance in a high traffic area.
Therefore locate your lights in a position that is unlikely to set off your
Radar360˚light from incidental movement inside your house.
SM OFF
SM OFF SM OFF
SM OFF
SM OFF
IMPORTANT – IDENTIFY YOUR MASTER LIGHT SO IT CAN BE EASILY
LOCATED IN THE FUTURE. It will be needed when adding new Radar 360˚
lights to the network in the future. Switch should be set to “M” (for Master)
position. We also suggest also tieing something bright or easy to see to the
neck between the panel & light.
10. If the link is not working as expected, simply reset your lights to factory
setting by following the “Unlinking your Radar 360˚Light” Instructions
and then start again.
63729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 463729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 4 21/08/2023 11:19:33 AM21/08/2023 11:19:33 AM
OPERATING INSTRUCTIONS
CHARGING YOUR RADAR 360˚LIGHTS
FOR THE FIRST TIME
1. Find a location where your light is exposed to full sunlight for at least 8
hours. This will typically require a full day so start charging in the morning.
2. Turn your light switch to the “M”
position for charging to commence.
3. After charging is complete or it is getting
dark, turn your switch to OFF until you are
ready to start the LINK process. This
prevents the battery from running down
again, if there is a delay between charging,
LINKING and installation.
The switch located on the bottom of the solar light housing is to turn on the
product and also to link your Radar 360˚linkable lights together (if you are
creating a linked network)
LINKING YOUR RADAR 360˚LIGHTS FOR THE FIRST TIME
Only TWO (2) Lights (for linking 3 or more lights, please see website)
1. Make sure your lights are fully charged before you commence
the Link procedure.
2. Take the 2 lights you wish to pair and place
the lights upwards on a level flat surface.
3. Choose one light to be a Master light.
The other light(s) will then be
Secondary light.
TOOLS REQUIRED TO INSTALL (not included)
Electric
Power Drill
Phillips
Screwdriver
Pencil Ladder Eye
Protection
Level
PARTS LIST
4
wall inserts
4
phillips screws
1
solar panel
1
light unit
GENERAL PRECAUTIONS
Keep out of reach of children.
PRE-INSTALLATION
•
•
Carefully remove the fixture from carton and check that all parts are included.
Carefully remove the fixture from carton and check that all parts are included.
Be careful not to misplace any of the parts needed for installation.
Be careful not to misplace any of the parts needed for installation.
•
•
For best results, determine light placement location before assembly. Charge
For best results, determine light placement location before assembly. Charge
the light in full sunlight for 24 hours prior to using.
the light in full sunlight for 24 hours prior to using.
INSTALLATION
Choose an ideal location.
Choose an outdoor location with full, direct sunlight
Choose an outdoor location with full, direct sunlight
so that the solar panel can receive at least 6-8 hours
so that the solar panel can receive at least 6-8 hours
of sunlight each day. Shady locations will result
of sunlight each day. Shady locations will result
in the battery receiving less energy and shorten
in the battery receiving less energy and shorten
the duration of illumination at night. The selected
the duration of illumination at night. The selected
location should not be near strong lighting sources
location should not be near strong lighting sources
such as street lights. This may cause the light to turn
such as street lights. This may cause the light to turn
off automatically as the built-in sensor detects the
off automatically as the built-in sensor detects the
nearby lighting source.
nearby lighting source.
The Maxima+ Security Light uses a highly sensitive
The Maxima+ Security Light uses a highly sensitive
motion sensor. Therefore placement position of the
motion sensor. Therefore placement position of the
light is important. For best results we recommend
light is important. For best results we recommend
you place the Maxima+ 7m away from areas where
you place the Maxima+ 7m away from areas where
it is likely to be triggered by unintended movement.
it is likely to be triggered by unintended movement.
For example, windows where there is regular
For example, windows where there is regular
movement in the house.
movement in the house. NOTE:
The Radar360˚linkable
signal can penetrate most
obstacles. The signal CANNOT
penetrate metal objects.
36
SM OFF
SM OFF
MASTER SECONDARY
63729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 363729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 3 21/08/2023 11:19:33 AM21/08/2023 11:19:33 AM
Introducing
Radar 360° + LINKABLE is the new next-generation solar sensor light from Cole
& Bright. The new “LINKABLE” technology turns a single security light into a
potential chain of security lights.
Radar 360° + LINKABLE requires no wires, hardware, or additional components
- just another Radar 360° + LINKABLE light in the vicinity.
Radar 360° + LINKABLE lights do not have to be the same. The technology
spans the Radar 360° + LINKABLE range, allowing youto connect a post light
to a wall-mounted light or an inground spotlight to a post light, helping to
create a well-lit, secure and safer environment around the home.
Any solar light can be a security light with Cole and Bright.
The Maxima+ Solar Security Light has an ULTRA BRIGHT mode because it is
a spotlight. Other LINKABLE lights in the RADAR 360˚Linkable Range may
also have an AMBIENCE mode.
RADAR 360˚+ Linkable lights require no mains wiring - the solar light is
charged by energy from the sun.
Easy to use SMART CONTROL FUNCTION allows you to link multiple
Radar 360˚lights to create a network of multiple lights that illuminate
the perimeter around your home when triggered.
ULTRA BRIGHT
SENSOR MODE
MAXIMUM ENERGY SAVING
SMART CONTROL FUNCTION
2 7
approx.7 m
approx. 5 m
360°
LINKABLE
63729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 263729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 2 21/08/2023 11:19:32 AM21/08/2023 11:19:32 AM
Brunnings Import Export Pty Limited
3/19-23 Clarinda Road,
Oakleigh South VIC 3167
63729
CARE AND MAINTENANCE
• From time to time, ensure the plug between the solar panel and light is
• From time to time, ensure the plug between the solar panel and light is
securely connected.
securely connected.
• It is advised to adjust the angle of the solar panel to optimise the exposure
• It is advised to adjust the angle of the solar panel to optimise the exposure
to the sun during the winter months.
to the sun during the winter months.
• The solar panel and the lens should be cleaned with a damp cotton cloth
• The solar panel and the lens should be cleaned with a damp cotton cloth
on a regular basis to ensure optimal performance. Periodically, utilise the
on a regular basis to ensure optimal performance. Periodically, utilise the
same technique to clean the lens of the motion light.
same technique to clean the lens of the motion light.
• Never let any abrasive material come into contact with the solar panel.
• Never let any abrasive material come into contact with the solar panel.
For recycling and disposal of batteries to protect the environment, please check the
internet or your local phone directory for local recycling centres and/or follow local
government regulations.
TROUBLESHOOTING
PROBLEM
Light will not come on.
Light will not come on.
POSSIBLE CAUSES
•
•
Solar panel not positioned in direct sunlight.
Solar panel not positioned in direct sunlight.
•
•
Battery pack not fully charged.
Battery pack not fully charged.
•
•
Solar panel no longer as bright.
Solar panel no longer as bright.
SOLUTION
•
•
Reposition the solar panel.
Reposition the solar panel.
•
•
Recharge the battery pack
Recharge the battery pack
•
•
Sun exposure may fluctuate as the season change.
Sun exposure may fluctuate as the season change.
Reposition the light or replace the battery pack.
Reposition the light or replace the battery pack.
If you are doing any of the following go to the
locations below for detailed instructions -
LINKING 3 OR MORE LIGHTS (FOR THE FIRST TIME)
LINKING 3 OR MORE LIGHTS (FOR THE FIRST TIME)
ADDING A NEW LIGHT(S) TO THE LINKED NETWORK
ADDING A NEW LIGHT(S) TO THE LINKED NETWORK
ADDING A NEW LIGHT(S) TO THE LINKED NETWORK
ADDING A NEW LIGHT(S) TO THE LINKED NETWORK
(but you can’t find the Original Master Light)
(but you can’t find the Original Master Light)
• Our website link: www.brunnings.com.au
• Our website link: www.brunnings.com.au
• Scan the QR code on the right
• Scan the QR code on the right
• Go to our How To Videos:
• Go to our How To Videos:
www.youtube.com/Radar360linkable
www.youtube.com/Radar360linkable
IMPORTANT INFORMATION
• Keep these instructions safe for future reference.
• Your motion light and solar panel are both weatherproof.
• You can mount your motion light indoors, but your solar panel must be
installed outdoors to receive light from the sun.
• If using a step ladder, you may require a second person to help install
the solar motion light.
• Prior to installation, lay out all the components and check the part list
section in this manual.
• Never look directly into the solar motion light when illuminated.
• If you locate your light in the vicinity of windows or glass doors,
movement may trigger the sensor to turn the lights on. Locate your lights
with this in mind.
IMPORTANT: READ ALL SAFETY INFORMATION AND INSTALLATION
IMPORTANT: READ ALL SAFETY INFORMATION AND INSTALLATION
INSTRUCTIONS BEFORE INSTALLING OR SERVICING THIS PRODUCT.
INSTRUCTIONS BEFORE INSTALLING OR SERVICING THIS PRODUCT.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
SOLAR POWERED + LINKABLE
MAXIMA SECURITY LIGHT
Customer Helpline: 03 9543 5600
SCAN HERE
FOR MORE
INFORMATION
PO
RTANT INF
O
RMATI
O
N
eep these instructions safe for future reference
MAXIMA SECURITY
LIGHMAXIMA SECURITY LIGH
360°
with
with
LINKABLE
63729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 163729P CB Maxima+ Solar Radar 360 Security Light Instruction Sheet.indd 1 21/08/2023 11:19:26 AM21/08/2023 11:19:26 AM
Table of contents
