Color imagination LEDPAR 36AS 7*10W 4IN1 SI-016 User manual

9CH Mode
LEDPAR
LEDPAR
LEDPAR
LEDPAR 36AS
36AS
36AS
36AS 7*10
7*10
7*10
7*10 W
W
W
W 4IN1
4IN1
4IN1
4IN1 SI-0
SI-0
SI-0
SI-0 16
16
16
16
For
For
For
For your
your
your
your own
own
own
own safety,
safety,
safety,
safety, please
please
please
please read
read
read
read this
this
this
this user
user
user
user manual
manual
manual
manual carefully
carefully
carefully
carefully before
before
before
before your
your
your
your initially
initially
initially
initially start-up!
start-up!
start-up!
start-up!
Every person involved with the installation, operation and maintenance of this device has to
- be qualified
- follow the instructions in this manual
- consider this manual to be part of the total product
- keep this manual for the entire service life of the product
- pass this manual on to every further owner or user of the product
- include every supplementary update with the original manual
B efore your initial start-up, please make sure that there is no damage caused during shipment. Should there be
any, do not use the device and consult your supplier.
SAFETY
SAFETY
SAFETY
SAFETY INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
INSTRUCTIONS
Cautions!
Cautions!
Cautions!
Cautions! Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure
a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written
in this user manual.
Important
Important
Important
Important ：Damages caused by the disregard of th is user manual are not subject to warranty. The dealer
will not accept liability for any resulting defects or problems.
If the device has been exposed to drastic temperature fluctuations (e.g. after delivery), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until it has
reached room temperature.
This device is allowed to be operated with an AC 90-260V , and is designed for indoor use only. Make sure the
available voltage is not higher!. This device fails under protection class!. The power plug must only be plugged
into a protection-class I outlet. The Green or Yellowish-Green conductor must be earthed!
Check the device and the power cord from time to time. Make sure the power cord is not crimped or damaged by
sharp edges. Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular cautions! Always connect the device to the mains least. Always
disconnect from the mains, when the device is not is user or before cleaning it. Never leave the device running
unattended!
Operate the device only after having familiarized with its functions. Keep away children and amateurs from the
device!
Do not shake the device. Avoid brute force when installing or operating. Do not permit operation by person not
qualified for operating the device. Most damages are the result of unprofessional operation!
There are no serviceable parts inside the device. Maintenance and service operations can be only carried by a
qualified person.
Please consider that unauthorized modifications on the device are forbidden due to safety reasons! Please note
that damages caused by manual modifications on the device or unauthorized operation by unqualified persons
are not subject to warranty. If this device will be operated in any way different to the one described in this manual,
it may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers
like short-circuit, electric shock, etc.
Channel Function Value Description
1 Dimmer 0-255 0-100% Linear Dimmer
2 Red 0-255 0-100% Red Dimmer
3 Green 0-255 0-100% Green Dimmer
4 Blue 0-255 0-100% Blue Dimmer
5 White 0-255 0-100% White Dimmer
6 Strobe
0- 015 LED OFF
016-255 Strobe effect from slow to fast
7 Auto
0- 015 LED OFF
016-255 Auto color mixing from slow to fast
8 Speed 0-255 Speed of Auto color mixing and strobe from slow to fast
9
Sound
Control
0-127 Sound control OFF (from controller)
128-255 Sound control ON (from controller)

BACK
BACK
BACK
BACK PANEL
PANEL
PANEL
PANEL
OPERATIONS
OPERATIONS
OPERATIONS
OPERATIONS
DMX512
DMX512
DMX512
DMX512 Connection
Connection
Connection
Connection
Only use a stereo shielded cable and 3-pin plugs and connectors in order to
connect the controller with the fixture r one fixture with another 。
Occupation
Occupation
Occupation
Occupation of
of
of
of the
the
the
the XLR
XLR
XLR
XLR Connection:
Connection:
Connection:
Connection:
The wire must not come into contact with each other, otherwise the fixtures will not work at all, or will
not work properly
If you are using controllers with this occupation, you can connect the DMX output of the controller directly with the
DMX input of the first device in the DMX chain. If you wish to connect DMX controllers with other XLR outputs,
you need to use adapter cables.
Building
Building
Building
Building A
A
A
A Serial
Serial
Serial
Serial DMX
DMX
DMX
DMX Chain
Chain
Chain
Chain ：
：
：
：Connect the DMX output of the 1
st
device in the DMX chain with the DMX input
of the next device. Always connect one output with the input of the next until all devices are connected.
Caution
Caution
Caution
Caution ：
：
：
：At the last device, the DMX cable has to be terminated with a terminator. Solder a 120 ohm resistor
between Data ( -) and Data ( +) into a 3-pin XLR plug and plug it in the DMX output of the last device.
DMX
DMX
DMX
DMX Start
Start
Start
Start Address
Address
Address
Address Setting
Setting
Setting
Setting
This device has 4 or 9 DMX channels. If you set, for example, the start address to channel 1, the device will use
the channels #1
st
to 4
th
or # 1
st
to 9
th
for control. T h e first available channel for the next fixture will be the 5
th
or
10
th
. Please be sure that you do not have any overlapping channels in order to control each device correctly and
independently from any other fixture on the DMX chain. If two, three or more devices are addressed similarly ,
they will work similarly.
Press the menu button until it shows AXXX in the display. XXX is the address you se last time. Press UP or
DOWN button to select your desired address, etc, A001. Press ENTER button to save or press MENU button to
exit.
LED
LED
LED
LED Display
Display
Display
Display Illustration
Illustration
Illustration
Illustration
MENU:
MENU:
MENU:
MENU: "EXIT"button. Only exit but will stay in the current working mode.
UP:
UP:
UP:
UP: Increase DMX value or to move upper menu.
DOWN:
DOWN:
DOWN:
DOWN: Decrease DMX value or move to next menu.
ENTER:
ENTER:
ENTER:
ENTER: Select the need menu.
Menu
Menu
Menu
Menu Illustration
Illustration
Illustration
Illustration
ADDR:
ADDR:
ADDR:
ADDR: A001-A512
CHND:
CHND:
CHND:
CHND: DMX channel modes, 4CH or 9CH
SLND:
SLND:
SLND:
SLND: Select MASTER/SLAVE mode
SHND:
SHND:
SHND:
SHND: SOUN means sound control. COLO means colors (COL1-CLO15) AUTO means auto mode(Speed:
SP01-SP08). FADE means color fading(Speed: SP01-SP08).
MANU:
MANU:
MANU:
MANU: Manual control for colors (RED: 0-255; GREEN: 0-255: BLUE: 0-255; WHITE: 0-255). When it's set, it will
stay in current value even the power is OFF.
TEST:
TEST:
TEST:
TEST: Colors auto test(R,G,B,W)
FHRS:
FHRS:
FHRS:
FHRS: Total operating times for the light.
TECHNIAL
TECHNIAL
TECHNIAL
TECHNIAL SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
Input Voltage AC90-260V 50/60Hz
Power Consumption 75 W
LED Quantity 7 * 10 W LEDs （4-IN-1 ）
Life Span 50000H
DMX Channel 4CH/9 CH
DMX
DMX
DMX
DMX Channel
Channel
Channel
Channel
4CH Mode
Channel Function Value Description
1 Red 0-255 0-100% Red Dimmer
2 Green 0-255 0-100% Green Dimmer
3 Blue 0-255 0-100% Blue Dimmer
4 White 0-255 0-100% White Dimmer