Color Splash LPL-2030-12-2 Operating instructions

Color SplashTM 2G
Installation and
Operation Guide
COLOR SPLASH 2G REPLACEMENT MULTI-COLOR LED
IN-GROUND POOL AND SPA LIGHTS Model #s:
LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2
WARNING!
Permanent damage to the 12V AC lamp will
occur if installed on a 120V AC circuit.
DANGER!
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION
This device is not intended for use in anything
other than in-ground pools and spas.
1Rated Lamp Life
Safety Precautions
IMPORTANT NOTE: Color Splash 2G lights are recommended for
installation by a qualifed spa or pool professional. Color Splash lights
cannot be used with dimming systems. Doing so will void the warranty.
Attention: As part of your normal maintenance program, J&J Electronics
recommends that all light fixtures be inspected and replaced as necessary
to ensure proper operation of your Color Splash 2G lamps.
2
J&J ELECTRONICS, INC. 3-YEAR LIMITED WARRANTY
©2014 J&J Electronics, Inc. All rights reserved. ColorGlo and Color Splash are trademarks of J&J Electronics, Inc.
All registered and trademarked brands and names are the property of their respective companies.
REV.112514
7
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights offer a
variety of microprocessor controlled lighting effects that will instantly transform
your pool or spa into a color-rich paradise.
The illumination generated by the Color Splash 2G Replacement Multi-Color LED
Pool and Spa lights is based on Light Emitting Diode (LED) technology. The
average expected lamp life is rated up to 50,000 elapsed time hours under
normal operating conditions. [Temperature: -20°F to 110°F (-29°C to 43°C),
Humidity: 5-95% non-condensing].
• Do not open, service or tamper with any internal component of the Color
Splash Replacement Multi-Color LED In-ground Pool or Spa light. Doing so will
void the warranty. Follow each instruction in this owner’s manual and pay
careful attention to all warnings.
• Do not directly expose or immerse the Color Splash Replacement Multi-Color
LED In-ground Pool or Spa light in water without containing it in a proper
watertight light housing and niche assembly.
• Keep the pool or spa light dry.
• Handle the Color Splash Replacement Multi-Color LED In-ground Pool or Spa
light with care. Be careful not to drop the unit.
This owner’s manual contains important information on installing and using your
new Color Splash Replacement Multi-Color LED In-ground Pool or Spa light. Please
read it carefully and keep it in a safe place for future reference.
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are
available in 12V AC (low voltage) and 120V AC models as indicated on the product
packaging. Each light has a screw-in Edison base.
Always disconnect power to the pool or spa light at the circuit breaker panel before
attempting to service the light. Failure to do so could result in serious injury or death
due to electrical shock. Refer to the original manufacturer’s pool or spa installation
manual before proceeding. As with any electrical device, installation and service
should always be performed by a qualifed individual.
(For LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2)
J&J Electronics, Inc. (“J&J”) warrants the above-referenced model numbers of Color Splash 2G Multi-Color LED In-ground
Pool and Spa Lamp (the “Product”) to be free from defects in material and workmanship, under normal use, conditions and
service, for a period of three (3) years from the original date of purchase, subject to the terms specified herein. If during
the warranty period, the Product fails to operate due to a defect in material or workmanship, J&J will, at its option, repair
or replace the Product at no charge.
TERMS AND CONDITIONS
This warranty is available to the original purchaser of the product(s) only. This warranty applies only when products are
properly installed in an in-ground pool; any other use voids the warranty. Products must be used in lighting equipment
designed and approved for the application and in environmental conditions within the normal specified operating range.
This warranty does not apply to any abnormal use of product(s), use in violation of any applicable standard, code or
instructions for use in installations including those contained in the latest National Electrical Code (NEC), the Standards
for Safety of Underwriters Laboratory, Inc. (UL), Standards for the American National Standards Institute (ANSI). This
warranty will not apply in the event of conditions demonstrating abnormal use or stress, freezing, operating when not fully
submerged, under/over voltage/current conditions, excessive switching cycles or operating hours or outside the
recommended operating conditions. This warranty does not apply to color shifts or dimming caused by emissions and/or
LED color shifts and dimming that naturally occurs over time. Warranty conditions: If the product operates for 15 or
more hours per day or continuously for 24 hours per day, the product warranty period stated shall be reduced to half
the stated period. This warranty does not cover damage occurring during shipment, damage or failure resulting from
alteration, accident, acts of God, theft, abuse, negligent installation, improper service, unauthorized repairs, freezing or
where adequate care has not been taken to prevent damage to the product(s). Tampering with any internal component of
this product(s) will void the warranty.
This warranty gives you specific rights. You may have other rights that vary according to the laws of your state.
LIMITATION OF LIABILITY
THE FOREGOING SHALL CONSTITUTE THE EXCLUSIVE REMEDY OF THE PURCHASER AND IS IN LIEU OF ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, AND ALL WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OR TRADE. THE
LIABILITY OF J&J UNDER THIS WARRANTY SHALL BE LIMITED TO THE REPLACEMENT, REPAIR OR PRO-RATED CREDIT OF
THE PRODUCT(S) AS STATED HEREIN. J&J IS NOT RESPONSIBLE FOR SHIPPING OR TRANSPORTATION COSTS RELATED
TO OBTAINING WARRANTY SERVICE. IN NO EVENT SHALL J&J BE LIABLE FOR ANY OTHER COSTS OR DAMAGES,
INCLUDING LOST PROFITS OR REVENUES, LABOR CHARGES OR FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES.
J&J reserves the right to change the warranty, warranty period without prior notice and without incurring obligation.
To obtain warranty service, retain the failed Product; retain the installation invoice showing product purchase price and
contact J&J Electronics, Inc. at 800.735.4553 ext. 242 or [email protected]. As of 01/21/2014

Color SplashTM 2G
Installation and
Operation Guide
COLOR SPLASH 2G REPLACEMENT MULTI-COLOR LED
IN-GROUND POOL AND SPA LIGHTS Model #s:
LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2
WARNING!
Permanent damage to the 12V AC lamp will
occur if installed on a 120V AC circuit.
DANGER!
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION
This device is not intended for use in anything
other than in-ground pools and spas.
1
Rated Lamp Life
Safety Precautions
IMPORTANT NOTE: Color Splash 2G lights are recommended for
installation by a qualifed spa or pool professional. Color Splash lights
cannot be used with dimming systems. Doing so will void the warranty.
Attention: As part of your normal maintenance program, J&J Electronics
recommends that all light fixtures be inspected and replaced as necessary
to ensure proper operation of your Color Splash 2G lamps.
2
J&J ELECTRONICS, INC. 3-YEAR LIMITED WARRANTY
©2014 J&J Electronics, Inc. All rights reserved. ColorGlo and Color Splash are trademarks of J&J Electronics, Inc.
All registered and trademarked brands and names are the property of their respective companies.
REV.112514
7
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights offer a
variety of microprocessor controlled lighting effects that will instantly transform
your pool or spa into a color-rich paradise.
The illumination generated by the Color Splash 2G Replacement Multi-Color LED
Pool and Spa lights is based on Light Emitting Diode (LED) technology. The
average expected lamp life is rated up to 50,000 elapsed time hours under
normal operating conditions. [Temperature: -20°F to 110°F (-29°C to 43°C),
Humidity: 5-95% non-condensing].
• Do not open, service or tamper with any internal component of the Color
Splash Replacement Multi-Color LED In-ground Pool or Spa light. Doing so will
void the warranty. Follow each instruction in this owner’s manual and pay
careful attention to all warnings.
• Do not directly expose or immerse the Color Splash Replacement Multi-Color
LED In-ground Pool or Spa light in water without containing it in a proper
watertight light housing and niche assembly.
• Keep the pool or spa light dry.
• Handle the Color Splash Replacement Multi-Color LED In-ground Pool or Spa
light with care. Be careful not to drop the unit.
This owner’s manual contains important information on installing and using your
new Color Splash Replacement Multi-Color LED In-ground Pool or Spa light. Please
read it carefully and keep it in a safe place for future reference.
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are
available in 12V AC (low voltage) and 120V AC models as indicated on the product
packaging. Each light has a screw-in Edison base.
Always disconnect power to the pool or spa light at the circuit breaker panel before
attempting to service the light. Failure to do so could result in serious injury or death
due to electrical shock. Refer to the original manufacturer’s pool or spa installation
manual before proceeding. As with any electrical device, installation and service
should always be performed by a qualifed individual.
(For LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2)
J&J Electronics, Inc. (“J&J”) warrants the above-referenced model numbers of Color Splash 2G Multi-Color LED In-ground
Pool and Spa Lamp (the “Product”) to be free from defects in material and workmanship, under normal use, conditions and
service, for a period of three (3) years from the original date of purchase, subject to the terms specified herein. If during
the warranty period, the Product fails to operate due to a defect in material or workmanship, J&J will, at its option, repair
or replace the Product at no charge.
TERMS AND CONDITIONS
This warranty is available to the original purchaser of the product(s) only. This warranty applies only when products are
properly installed in an in-ground pool; any other use voids the warranty. Products must be used in lighting equipment
designed and approved for the application and in environmental conditions within the normal specified operating range.
This warranty does not apply to any abnormal use of product(s), use in violation of any applicable standard, code or
instructions for use in installations including those contained in the latest National Electrical Code (NEC), the Standards
for Safety of Underwriters Laboratory, Inc. (UL), Standards for the American National Standards Institute (ANSI). This
warranty will not apply in the event of conditions demonstrating abnormal use or stress, freezing, operating when not fully
submerged, under/over voltage/current conditions, excessive switching cycles or operating hours or outside the
recommended operating conditions. This warranty does not apply to color shifts or dimming caused by emissions and/or
LED color shifts and dimming that naturally occurs over time. Warranty conditions: If the product operates for 15 or
more hours per day or continuously for 24 hours per day, the product warranty period stated shall be reduced to half
the stated period. This warranty does not cover damage occurring during shipment, damage or failure resulting from
alteration, accident, acts of God, theft, abuse, negligent installation, improper service, unauthorized repairs, freezing or
where adequate care has not been taken to prevent damage to the product(s). Tampering with any internal component of
this product(s) will void the warranty.
This warranty gives you specific rights. You may have other rights that vary according to the laws of your state.
LIMITATION OF LIABILITY
THE FOREGOING SHALL CONSTITUTE THE EXCLUSIVE REMEDY OF THE PURCHASER AND IS IN LIEU OF ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, AND ALL WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OR TRADE. THE
LIABILITY OF J&J UNDER THIS WARRANTY SHALL BE LIMITED TO THE REPLACEMENT, REPAIR OR PRO-RATED CREDIT OF
THE PRODUCT(S) AS STATED HEREIN. J&J IS NOT RESPONSIBLE FOR SHIPPING OR TRANSPORTATION COSTS RELATED
TO OBTAINING WARRANTY SERVICE. IN NO EVENT SHALL J&J BE LIABLE FOR ANY OTHER COSTS OR DAMAGES,
INCLUDING LOST PROFITS OR REVENUES, LABOR CHARGES OR FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES.
J&J reserves the right to change the warranty, warranty period without prior notice and without incurring obligation.
To obtain warranty service, retain the failed Product; retain the installation invoice showing product purchase price and
contact J&J Electronics, Inc. at 800.735.4553 ext. 242 or [email protected]. As of 01/21/2014

Color SplashTM 2G
Installation and
Operation Guide
COLOR SPLASH 2G REPLACEMENT MULTI-COLOR LED
IN-GROUND POOL AND SPA LIGHTS Model #s:
LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2
WARNING!
Permanent damage to the 12V AC lamp will
occur if installed on a 120V AC circuit.
DANGER!
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION
This device is not intended for use in anything
other than in-ground pools and spas.
1
Rated Lamp Life
Safety Precautions
IMPORTANT NOTE: Color Splash 2G lights are recommended for
installation by a qualifed spa or pool professional. Color Splash lights
cannot be used with dimming systems. Doing so will void the warranty.
Attention: As part of your normal maintenance program, J&J Electronics
recommends that all light fixtures be inspected and replaced as necessary
to ensure proper operation of your Color Splash 2G lamps.
2
J&J ELECTRONICS, INC. 3-YEAR LIMITED WARRANTY
©2014 J&J Electronics, Inc. All rights reserved. ColorGlo and Color Splash are trademarks of J&J Electronics, Inc.
All registered and trademarked brands and names are the property of their respective companies.
REV.112514
7
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights offer a
variety of microprocessor controlled lighting effects that will instantly transform
your pool or spa into a color-rich paradise.
The illumination generated by the Color Splash 2G Replacement Multi-Color LED
Pool and Spa lights is based on Light Emitting Diode (LED) technology. The
average expected lamp life is rated up to 50,000 elapsed time hours under
normal operating conditions. [Temperature: -20°F to 110°F (-29°C to 43°C),
Humidity: 5-95% non-condensing].
• Do not open, service or tamper with any internal component of the Color
Splash Replacement Multi-Color LED In-ground Pool or Spa light. Doing so will
void the warranty. Follow each instruction in this owner’s manual and pay
careful attention to all warnings.
• Do not directly expose or immerse the Color Splash Replacement Multi-Color
LED In-ground Pool or Spa light in water without containing it in a proper
watertight light housing and niche assembly.
• Keep the pool or spa light dry.
• Handle the Color Splash Replacement Multi-Color LED In-ground Pool or Spa
light with care. Be careful not to drop the unit.
This owner’s manual contains important information on installing and using your
new Color Splash Replacement Multi-Color LED In-ground Pool or Spa light. Please
read it carefully and keep it in a safe place for future reference.
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are
available in 12V AC (low voltage) and 120V AC models as indicated on the product
packaging. Each light has a screw-in Edison base.
Always disconnect power to the pool or spa light at the circuit breaker panel before
attempting to service the light. Failure to do so could result in serious injury or death
due to electrical shock. Refer to the original manufacturer’s pool or spa installation
manual before proceeding. As with any electrical device, installation and service
should always be performed by a qualifed individual.
(For LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2)
J&J Electronics, Inc. (“J&J”) warrants the above-referenced model numbers of Color Splash 2G Multi-Color LED In-ground
Pool and Spa Lamp (the “Product”) to be free from defects in material and workmanship, under normal use, conditions and
service, for a period of three (3) years from the original date of purchase, subject to the terms specified herein. If during
the warranty period, the Product fails to operate due to a defect in material or workmanship, J&J will, at its option, repair
or replace the Product at no charge.
TERMS AND CONDITIONS
This warranty is available to the original purchaser of the product(s) only. This warranty applies only when products are
properly installed in an in-ground pool; any other use voids the warranty. Products must be used in lighting equipment
designed and approved for the application and in environmental conditions within the normal specified operating range.
This warranty does not apply to any abnormal use of product(s), use in violation of any applicable standard, code or
instructions for use in installations including those contained in the latest National Electrical Code (NEC), the Standards
for Safety of Underwriters Laboratory, Inc. (UL), Standards for the American National Standards Institute (ANSI). This
warranty will not apply in the event of conditions demonstrating abnormal use or stress, freezing, operating when not fully
submerged, under/over voltage/current conditions, excessive switching cycles or operating hours or outside the
recommended operating conditions. This warranty does not apply to color shifts or dimming caused by emissions and/or
LED color shifts and dimming that naturally occurs over time. Warranty conditions: If the product operates for 15 or
more hours per day or continuously for 24 hours per day, the product warranty period stated shall be reduced to half
the stated period. This warranty does not cover damage occurring during shipment, damage or failure resulting from
alteration, accident, acts of God, theft, abuse, negligent installation, improper service, unauthorized repairs, freezing or
where adequate care has not been taken to prevent damage to the product(s). Tampering with any internal component of
this product(s) will void the warranty.
This warranty gives you specific rights. You may have other rights that vary according to the laws of your state.
LIMITATION OF LIABILITY
THE FOREGOING SHALL CONSTITUTE THE EXCLUSIVE REMEDY OF THE PURCHASER AND IS IN LIEU OF ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, AND ALL WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OR TRADE. THE
LIABILITY OF J&J UNDER THIS WARRANTY SHALL BE LIMITED TO THE REPLACEMENT, REPAIR OR PRO-RATED CREDIT OF
THE PRODUCT(S) AS STATED HEREIN. J&J IS NOT RESPONSIBLE FOR SHIPPING OR TRANSPORTATION COSTS RELATED
TO OBTAINING WARRANTY SERVICE. IN NO EVENT SHALL J&J BE LIABLE FOR ANY OTHER COSTS OR DAMAGES,
INCLUDING LOST PROFITS OR REVENUES, LABOR CHARGES OR FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES.
J&J reserves the right to change the warranty, warranty period without prior notice and without incurring obligation.
To obtain warranty service, retain the failed Product; retain the installation invoice showing product purchase price and
contact J&J Electronics, Inc. at 800.735.4553 ext. 242 or [email protected]. As of 01/21/2014

INSTALLATION
For LPL-2030-12-2/LPL-2030-110-2
LPL-7030-12-2/LPL-7030-110-2
Color Splash Replacement Multi-
Color LED In-ground Pool and Spa Lights
Your new Color Splash Replacement Multi-Color
LED In-ground Pool or Spa light fits most Edison
type 12V AC and 120V AC light sockets. It is not
for use with pools or spas that have current control
mechanisms or electronic dimming controllers.
COMPATIBILITY
Pool Light Housings: Hayward® Astrolite™ SP058 Series, Pentair® Amerlite 784 Series
Spa Light Housings: Hayward® Astrolite II SP059, Pentair® SpaBrite™ Series
STEP 1
MAKE SURE POWER IS TURNED OFF.
Be certain you are installing the correct
voltage Color Splash light
(120V AC or 12V AC).
Access the old light according to your
pool or spa manufacturer’s instructions.
Loosen the screws that hold the
existing light housing from the niche
assembly and place it on the pool deck.
There should be enough power cord
to do this easily. If there is not enough
power cord to allow the light housing
to reach the pool deck surface, call
your local pool service company.
Figure 1: LPL-2030
and LPL-7030
Pool Light
Spa Light
Figure 2: Step 1
Pool Deck Surface
The
niche
To GFCI,
Circuit
Breaker
and
Power
Source
STEP 2
Remove the screws and/or loosen the clamp that holds the face plate and lens in place.
Carefully remove the lens from the pool or spa light. Take care not to damage the surface
of the light housing body that makes contact with the lens gasket.
STEP 3
Remove the old bulb and
discard. You are now ready
to install your new Color
Splash 2G Replacement
Multi-Color LED In-
ground Pool or Spa light.
Carefully screw the
Color Splash light into
the socket. You are now
ready to re-assemble
the light housing.
STEP 4
WARNING!
Always install a new silicone lens gasket to ensure a positive seal.
Proceed by cleaning any gasket residue from the light housing body. A clean surface is
necessary for the new gasket to seat properly and prevent leakage. Install the new gasket.
Set the lens and faceplate in the light housing and re-assemble. Tighten the screws slightly,
allowing the gasket to seal evenly. Do not over tighten the screws.
Once the screws are tight, submerge the assembled light housing in the water and visually
check that air bubbles are not escaping from the gasket area. Should bubbles appear,
remove the light from the water and reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation by wrapping the
cord around the light housing and re-attaching the light housing to the niche assembly.
Reconnect power by resetting the circuit breaker to the “on” position. You are now ready
to enjoy your new Color Splash 2G Replacement Multi-Color LED In-ground Pool or Spa light.
Note on Figures 1-4: All figures are provided for illustration purposes only. Refer to the
original manufacturer’s pool or spa light installation manual for further reference.
OPERATION
For LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa Lights
Use the pool’s or spa’s current on/off light switch to control the light shows of your new Color Splash light.
Solid Colors
Your Color Splash 2G Replacement Multi-Color LED In-ground Pool or Spa light has seven solid
colors available for you to experience. Colors can be selected using the Color Lock feature.
1. Parisian Blue 2. Brazilian Red 3. Tahitian Blue 4. Miami Pink 5. Tuscan Orange 6. Arctic White
7. New Zealand Green
Light Shows and Color Blends
Your Color Splash light has five light shows from which you can choose:
1. Slow Splash 2. Fast Splash 3. Super Slow Splash 4. Patriotic Splash 5. Tidal Splash
The first three light shows display all seven solid colors, while the last two display selected
colors. All light shows, except Fast Splash, allow you to view multiple color blends. Color blends
occur when the light gradually blends one solid color into the next. Using the Color Lock feature,
you can stop the light at any point during the transition to select a color blend.
Choosing Colors and Light Shows
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are pre-programmed
and synchronous with each other while offering a wide array of lighting effects and options. They
offer five different light shows to choose from, as well as a Color Lock feature which allows you to
‘lock’ the light on any of the solid colors during a color blend show. The Color Splash light does
not require any special hardware, as it is controlled by using your existing pool light power switch.
Grounding Spring
G asket
Socket
Lens
Edison
Base
Figure 3: Steps 2-4
3
4
Changing light shows: To move from one light show to another, turn the pool light
power off for 2 seconds and then back on again.
Slow Splash (Factory Default Light Show.)
Show: Slow cross-fade through all seven solid colors.
Cycle: Two minute color sequence cycle with slow cross-fade between colors. Light will hold
on each solid color for 8 seconds before moving to the next.
Fast Splash
Show: Quick and random flashes through the seven solid colors.
Cycle: Random fast change between solid colors in half second intervals.
Super Slow Splash
Show: Very slow cross-fade through all seven solid colors.
Cycle: Seventy-seven minute color sequence cycle with super slow cross-fade between solid
colors. Light will stay on each solid color for 10 minutes before moving to the next.
Patriotic Splash
Show: Quick cross-fade through red, white and blue.
Cycle: Eleven second cycle through red, white and blue with quick cross-fade between colors.
Light will stay on each solid color for 3 seconds before moving to the next.
Tidal Splash
Show: Slow cross-fade between green and blue.
Cycle: Twenty-four second cycle through green and blue with slow cross-fade between solid colors.
(TIP: The Slow Splash light show is the best show to use in order to practice using the Color Lock feature of the light.)
Memory Mode: When your Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa
lights are turned off for at least 8 seconds, the color or light show on display will be stored. The
next time the power is turned on, the light will resume displaying that same color or light show.
Reset Mode: For multi-light installations, should your Color Splash 2G Replacement Multi-Color LED
Pool or Spa lights become asynchronous (non-synchronous), you can reset your lights using your
pool light switch. To activate the reset mode, turn the power off for 5-7 seconds and then back
on again. The lights will indicate that they have been reset by flashing red a few times. When
you reset the Color Splash lights they will go back to the Slow Splash light show.
5
6
NOTE: Your Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are “synchronous”,
meaning you can experience the same light shows in your pool and spa at the same time. However, all of
the pool and spa lights must be on the same electrical circuit for this feature to be operational. Please
consult a qualified electrician to determine your specific pool and spa circuit configuration.
Using the Color Lock feature: The Color Lock feature allows you to ‘lock’ the light on any of the
solid colors during a color blend show. To activate the Color Lock feature during any of the Color Splash
2G LED Pool or Spa light’s shows, when the desired color is reached turn the pool light power off and
then back on again within 1 seconds. To deactivate the Color Lock feature and resume thelight show,
turn the pool light power off and then back on again within 1 seconds.

INSTALLATION
For LPL-2030-12-2/LPL-2030-110-2
LPL-7030-12-2/LPL-7030-110-2
Color Splash Replacement Multi-
Color LED In-ground Pool and Spa Lights
Your new Color Splash Replacement Multi-Color
LED In-ground Pool or Spa light fits most Edison
type 12V AC and 120V AC light sockets. It is not
for use with pools or spas that have current control
mechanisms or electronic dimming controllers.
COMPATIBILITY
Pool Light Housings: Hayward® Astrolite™ SP058 Series, Pentair® Amerlite 784 Series
Spa Light Housings: Hayward® Astrolite II SP059, Pentair® SpaBrite™ Series
STEP 1
MAKE SURE POWER IS TURNED OFF.
Be certain you are installing the correct
voltage Color Splash light
(120V AC or 12V AC).
Access the old light according to your
pool or spa manufacturer’s instructions.
Loosen the screws that hold the
existing light housing from the niche
assembly and place it on the pool deck.
There should be enough power cord
to do this easily. If there is not enough
power cord to allow the light housing
to reach the pool deck surface, call
your local pool service company.
Figure 1: LPL-2030
and LPL-7030
Pool Light
Spa Light
Figure 2: Step 1
Pool Deck Surface
The
niche
To GFCI,
Circuit
Breaker
and
Power
Source
STEP 2
Remove the screws and/or loosen the clamp that holds the face plate and lens in place.
Carefully remove the lens from the pool or spa light. Take care not to damage the surface
of the light housing body that makes contact with the lens gasket.
STEP 3
Remove the old bulb and
discard. You are now ready
to install your new Color
Splash 2G Replacement
Multi-Color LED In-
ground Pool or Spa light.
Carefully screw the
Color Splash light into
the socket. You are now
ready to re-assemble
the light housing.
STEP 4
WARNING!
Always install a new silicone lens gasket to ensure a positive seal.
Proceed by cleaning any gasket residue from the light housing body. A clean surface is
necessary for the new gasket to seat properly and prevent leakage. Install the new gasket.
Set the lens and faceplate in the light housing and re-assemble. Tighten the screws slightly,
allowing the gasket to seal evenly. Do not over tighten the screws.
Once the screws are tight, submerge the assembled light housing in the water and visually
check that air bubbles are not escaping from the gasket area. Should bubbles appear,
remove the light from the water and reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation by wrapping the
cord around the light housing and re-attaching the light housing to the niche assembly.
Reconnect power by resetting the circuit breaker to the “on” position. You are now ready
to enjoy your new Color Splash 2G Replacement Multi-Color LED In-ground Pool or Spa light.
Note on Figures 1-4: All figures are provided for illustration purposes only. Refer to the
original manufacturer’s pool or spa light installation manual for further reference.
OPERATION
For LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa Lights
Use the pool’s or spa’s current on/off light switch to control the light shows of your new Color Splash light.
Solid Colors
Your Color Splash 2G Replacement Multi-Color LED In-ground Pool or Spa light has seven solid
colors available for you to experience. Colors can be selected using the Color Lock feature.
1. Parisian Blue 2. Brazilian Red 3. Tahitian Blue 4. Miami Pink 5. Tuscan Orange 6. Arctic White
7. New Zealand Green
Light Shows and Color Blends
Your Color Splash light has five light shows from which you can choose:
1. Slow Splash 2. Fast Splash 3. Super Slow Splash 4. Patriotic Splash 5. Tidal Splash
The first three light shows display all seven solid colors, while the last two display selected
colors. All light shows, except Fast Splash, allow you to view multiple color blends. Color blends
occur when the light gradually blends one solid color into the next. Using the Color Lock feature,
you can stop the light at any point during the transition to select a color blend.
Choosing Colors and Light Shows
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are pre-programmed
and synchronous with each other while offering a wide array of lighting effects and options. They
offer five different light shows to choose from, as well as a Color Lock feature which allows you to
‘lock’ the light on any of the solid colors during a color blend show. The Color Splash light does
not require any special hardware, as it is controlled by using your existing pool light power switch.
Grounding Spring
G asket
Socket
Lens
Edison
Base
Figure 3: Steps 2-4
3
4
Changing light shows: To move from one light show to another, turn the pool light
power off for 2 seconds and then back on again.
Slow Splash (Factory Default Light Show.)
Show: Slow cross-fade through all seven solid colors.
Cycle: Two minute color sequence cycle with slow cross-fade between colors. Light will hold
on each solid color for 8 seconds before moving to the next.
Fast Splash
Show: Quick and random flashes through the seven solid colors.
Cycle: Random fast change between solid colors in half second intervals.
Super Slow Splash
Show: Very slow cross-fade through all seven solid colors.
Cycle: Seventy-seven minute color sequence cycle with super slow cross-fade between solid
colors. Light will stay on each solid color for 10 minutes before moving to the next.
Patriotic Splash
Show: Quick cross-fade through red, white and blue.
Cycle: Eleven second cycle through red, white and blue with quick cross-fade between colors.
Light will stay on each solid color for 3 seconds before moving to the next.
Tidal Splash
Show: Slow cross-fade between green and blue.
Cycle: Twenty-four second cycle through green and blue with slow cross-fade between solid colors.
(TIP: The Slow Splash light show is the best show to use in order to practice using the Color Lock feature of the light.)
Memory Mode: When your Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa
lights are turned off for at least 8 seconds, the color or light show on display will be stored. The
next time the power is turned on, the light will resume displaying that same color or light show.
Reset Mode: For multi-light installations, should your Color Splash 2G Replacement Multi-Color LED
Pool or Spa lights become asynchronous (non-synchronous), you can reset your lights using your
pool light switch. To activate the reset mode, turn the power off for 5-7 seconds and then back
on again. The lights will indicate that they have been reset by flashing red a few times. When
you reset the Color Splash lights they will go back to the Slow Splash light show.
5
6
NOTE: Your Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are “synchronous”,
meaning you can experience the same light shows in your pool and spa at the same time. However, all of
the pool and spa lights must be on the same electrical circuit for this feature to be operational. Please
consult a qualified electrician to determine your specific pool and spa circuit configuration.
Using the Color Lock feature: The Color Lock feature allows you to ‘lock’ the light on any of the
solid colors during a color blend show. To activate the Color Lock feature during any of the Color Splash
2G LED Pool or Spa light’s shows, when the desired color is reached turn the pool light power off and
then back on again within 1 seconds. To deactivate the Color Lock feature and resume thelight show,
turn the pool light power off and then back on again within 1 seconds.

INSTALLATION
For LPL-2030-12-2/LPL-2030-110-2
LPL-7030-12-2/LPL-7030-110-2
Color Splash Replacement Multi-
Color LED In-ground Pool and Spa Lights
Your new Color Splash Replacement Multi-Color
LED In-ground Pool or Spa light fits most Edison
type 12V AC and 120V AC light sockets. It is not
for use with pools or spas that have current control
mechanisms or electronic dimming controllers.
COMPATIBILITY
Pool Light Housings: Hayward® Astrolite™ SP058 Series, Pentair® Amerlite 784 Series
Spa Light Housings: Hayward® Astrolite II SP059, Pentair® SpaBrite™ Series
STEP 1
MAKE SURE POWER IS TURNED OFF.
Be certain you are installing the correct
voltage Color Splash light
(120V AC or 12V AC).
Access the old light according to your
pool or spa manufacturer’s instructions.
Loosen the screws that hold the
existing light housing from the niche
assembly and place it on the pool deck.
There should be enough power cord
to do this easily. If there is not enough
power cord to allow the light housing
to reach the pool deck surface, call
your local pool service company.
Figure 1: LPL-2030
and LPL-7030
Pool Light
Spa Light
Figure 2: Step 1
Pool Deck Surface
The
niche
To GFCI,
Circuit
Breaker
and
Power
Source
STEP 2
Remove the screws and/or loosen the clamp that holds the face plate and lens in place.
Carefully remove the lens from the pool or spa light. Take care not to damage the surface
of the light housing body that makes contact with the lens gasket.
STEP 3
Remove the old bulb and
discard. You are now ready
to install your new Color
Splash 2G Replacement
Multi-Color LED In-
ground Pool or Spa light.
Carefully screw the
Color Splash light into
the socket. You are now
ready to re-assemble
the light housing.
STEP 4
WARNING!
Always install a new silicone lens gasket to ensure a positive seal.
Proceed by cleaning any gasket residue from the light housing body. A clean surface is
necessary for the new gasket to seat properly and prevent leakage. Install the new gasket.
Set the lens and faceplate in the light housing and re-assemble. Tighten the screws slightly,
allowing the gasket to seal evenly. Do not over tighten the screws.
Once the screws are tight, submerge the assembled light housing in the water and visually
check that air bubbles are not escaping from the gasket area. Should bubbles appear,
remove the light from the water and reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation by wrapping the
cord around the light housing and re-attaching the light housing to the niche assembly.
Reconnect power by resetting the circuit breaker to the “on” position. You are now ready
to enjoy your new Color Splash 2G Replacement Multi-Color LED In-ground Pool or Spa light.
Note on Figures 1-4: All figures are provided for illustration purposes only. Refer to the
original manufacturer’s pool or spa light installation manual for further reference.
OPERATION
For LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa Lights
Use the pool’s or spa’s current on/off light switch to control the light shows of your new Color Splash light.
Solid Colors
Your Color Splash 2G Replacement Multi-Color LED In-ground Pool or Spa light has seven solid
colors available for you to experience. Colors can be selected using the Color Lock feature.
1. Parisian Blue 2. Brazilian Red 3. Tahitian Blue 4. Miami Pink 5. Tuscan Orange 6. Arctic White
7. New Zealand Green
Light Shows and Color Blends
Your Color Splash light has five light shows from which you can choose:
1. Slow Splash 2. Fast Splash 3. Super Slow Splash 4. Patriotic Splash 5. Tidal Splash
The first three light shows display all seven solid colors, while the last two display selected
colors. All light shows, except Fast Splash, allow you to view multiple color blends. Color blends
occur when the light gradually blends one solid color into the next. Using the Color Lock feature,
you can stop the light at any point during the transition to select a color blend.
Choosing Colors and Light Shows
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are pre-programmed
and synchronous with each other while offering a wide array of lighting effects and options. They
offer five different light shows to choose from, as well as a Color Lock feature which allows you to
‘lock’ the light on any of the solid colors during a color blend show. The Color Splash light does
not require any special hardware, as it is controlled by using your existing pool light power switch.
Grounding Spring
G asket
Socket
Lens
Edison
Base
Figure 3: Steps 2-4
3
4
Changing light shows: To move from one light show to another, turn the pool light
power off for 2 seconds and then back on again.
Slow Splash (Factory Default Light Show.)
Show: Slow cross-fade through all seven solid colors.
Cycle: Two minute color sequence cycle with slow cross-fade between colors. Light will hold
on each solid color for 8 seconds before moving to the next.
Fast Splash
Show: Quick and random flashes through the seven solid colors.
Cycle: Random fast change between solid colors in half second intervals.
Super Slow Splash
Show: Very slow cross-fade through all seven solid colors.
Cycle: Seventy-seven minute color sequence cycle with super slow cross-fade between solid
colors. Light will stay on each solid color for 10 minutes before moving to the next.
Patriotic Splash
Show: Quick cross-fade through red, white and blue.
Cycle: Eleven second cycle through red, white and blue with quick cross-fade between colors.
Light will stay on each solid color for 3 seconds before moving to the next.
Tidal Splash
Show: Slow cross-fade between green and blue.
Cycle: Twenty-four second cycle through green and blue with slow cross-fade between solid colors.
(TIP: The Slow Splash light show is the best show to use in order to practice using the Color Lock feature of the light.)
Memory Mode: When your Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa
lights are turned off for at least 8 seconds, the color or light show on display will be stored. The
next time the power is turned on, the light will resume displaying that same color or light show.
Reset Mode: For multi-light installations, should your Color Splash 2G Replacement Multi-Color LED
Pool or Spa lights become asynchronous (non-synchronous), you can reset your lights using your
pool light switch. To activate the reset mode, turn the power off for 5-7 seconds and then back
on again. The lights will indicate that they have been reset by flashing red a few times. When
you reset the Color Splash lights they will go back to the Slow Splash light show.
5
6
NOTE: Your Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are “synchronous”,
meaning you can experience the same light shows in your pool and spa at the same time. However, all of
the pool and spa lights must be on the same electrical circuit for this feature to be operational. Please
consult a qualified electrician to determine your specific pool and spa circuit configuration.
Using the Color Lock feature: The Color Lock feature allows you to ‘lock’ the light on any of the
solid colors during a color blend show. To activate the Color Lock feature during any of the Color Splash
2G LED Pool or Spa light’s shows, when the desired color is reached turn the pool light power off and
then back on again within 1 seconds. To deactivate the Color Lock feature and resume thelight show,
turn the pool light power off and then back on again within 1 seconds.

INSTALLATION
For LPL-2030-12-2/LPL-2030-110-2
LPL-7030-12-2/LPL-7030-110-2
Color Splash Replacement Multi-
Color LED In-ground Pool and Spa Lights
Your new Color Splash Replacement Multi-Color
LED In-ground Pool or Spa light fits most Edison
type 12V AC and 120V AC light sockets. It is not
for use with pools or spas that have current control
mechanisms or electronic dimming controllers.
COMPATIBILITY
Pool Light Housings: Hayward® Astrolite™ SP058 Series, Pentair® Amerlite 784 Series
Spa Light Housings: Hayward® Astrolite II SP059, Pentair® SpaBrite™ Series
STEP 1
MAKE SURE POWER IS TURNED OFF.
Be certain you are installing the correct
voltage Color Splash light
(120V AC or 12V AC).
Access the old light according to your
pool or spa manufacturer’s instructions.
Loosen the screws that hold the
existing light housing from the niche
assembly and place it on the pool deck.
There should be enough power cord
to do this easily. If there is not enough
power cord to allow the light housing
to reach the pool deck surface, call
your local pool service company.
Figure 1: LPL-2030
and LPL-7030
Pool Light
Spa Light
Figure 2: Step 1
Pool Deck Surface
The
niche
To GFCI,
Circuit
Breaker
and
Power
Source
STEP 2
Remove the screws and/or loosen the clamp that holds the face plate and lens in place.
Carefully remove the lens from the pool or spa light. Take care not to damage the surface
of the light housing body that makes contact with the lens gasket.
STEP 3
Remove the old bulb and
discard. You are now ready
to install your new Color
Splash 2G Replacement
Multi-Color LED In-
ground Pool or Spa light.
Carefully screw the
Color Splash light into
the socket. You are now
ready to re-assemble
the light housing.
STEP 4
WARNING!
Always install a new silicone lens gasket to ensure a positive seal.
Proceed by cleaning any gasket residue from the light housing body. A clean surface is
necessary for the new gasket to seat properly and prevent leakage. Install the new gasket.
Set the lens and faceplate in the light housing and re-assemble. Tighten the screws slightly,
allowing the gasket to seal evenly. Do not over tighten the screws.
Once the screws are tight, submerge the assembled light housing in the water and visually
check that air bubbles are not escaping from the gasket area. Should bubbles appear,
remove the light from the water and reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation by wrapping the
cord around the light housing and re-attaching the light housing to the niche assembly.
Reconnect power by resetting the circuit breaker to the “on” position. You are now ready
to enjoy your new Color Splash 2G Replacement Multi-Color LED In-ground Pool or Spa light.
Note on Figures 1-4: All figures are provided for illustration purposes only. Refer to the
original manufacturer’s pool or spa light installation manual for further reference.
OPERATION
For LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa Lights
Use the pool’s or spa’s current on/off light switch to control the light shows of your new Color Splash light.
Solid Colors
Your Color Splash 2G Replacement Multi-Color LED In-ground Pool or Spa light has seven solid
colors available for you to experience. Colors can be selected using the Color Lock feature.
1. Parisian Blue 2. Brazilian Red 3. Tahitian Blue 4. Miami Pink 5. Tuscan Orange 6. Arctic White
7. New Zealand Green
Light Shows and Color Blends
Your Color Splash light has five light shows from which you can choose:
1. Slow Splash 2. Fast Splash 3. Super Slow Splash 4. Patriotic Splash 5. Tidal Splash
The first three light shows display all seven solid colors, while the last two display selected
colors. All light shows, except Fast Splash, allow you to view multiple color blends. Color blends
occur when the light gradually blends one solid color into the next. Using the Color Lock feature,
you can stop the light at any point during the transition to select a color blend.
Choosing Colors and Light Shows
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are pre-programmed
and synchronous with each other while offering a wide array of lighting effects and options. They
offer five different light shows to choose from, as well as a Color Lock feature which allows you to
‘lock’ the light on any of the solid colors during a color blend show. The Color Splash light does
not require any special hardware, as it is controlled by using your existing pool light power switch.
Grounding Spring
G asket
Socket
Lens
Edison
Base
Figure 3: Steps 2-4
3
4
Changing light shows: To move from one light show to another, turn the pool light
power off for 2 seconds and then back on again.
Slow Splash (Factory Default Light Show.)
Show: Slow cross-fade through all seven solid colors.
Cycle: Two minute color sequence cycle with slow cross-fade between colors. Light will hold
on each solid color for 8 seconds before moving to the next.
Fast Splash
Show: Quick and random flashes through the seven solid colors.
Cycle: Random fast change between solid colors in half second intervals.
Super Slow Splash
Show: Very slow cross-fade through all seven solid colors.
Cycle: Seventy-seven minute color sequence cycle with super slow cross-fade between solid
colors. Light will stay on each solid color for 10 minutes before moving to the next.
Patriotic Splash
Show: Quick cross-fade through red, white and blue.
Cycle: Eleven second cycle through red, white and blue with quick cross-fade between colors.
Light will stay on each solid color for 3 seconds before moving to the next.
Tidal Splash
Show: Slow cross-fade between green and blue.
Cycle: Twenty-four second cycle through green and blue with slow cross-fade between solid colors.
(TIP: The Slow Splash light show is the best show to use in order to practice using the Color Lock feature of the light.)
Memory Mode: When your Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa
lights are turned off for at least 8 seconds, the color or light show on display will be stored. The
next time the power is turned on, the light will resume displaying that same color or light show.
Reset Mode: For multi-light installations, should your Color Splash 2G Replacement Multi-Color LED
Pool or Spa lights become asynchronous (non-synchronous), you can reset your lights using your
pool light switch. To activate the reset mode, turn the power off for 5-7 seconds and then back
on again. The lights will indicate that they have been reset by flashing red a few times. When
you reset the Color Splash lights they will go back to the Slow Splash light show.
5
6
NOTE: Your Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are “synchronous”,
meaning you can experience the same light shows in your pool and spa at the same time. However, all of
the pool and spa lights must be on the same electrical circuit for this feature to be operational. Please
consult a qualified electrician to determine your specific pool and spa circuit configuration.
Using the Color Lock feature: The Color Lock feature allows you to ‘lock’ the light on any of the
solid colors during a color blend show. To activate the Color Lock feature during any of the Color Splash
2G LED Pool or Spa light’s shows, when the desired color is reached turn the pool light power off and
then back on again within 1 seconds. To deactivate the Color Lock feature and resume thelight show,
turn the pool light power off and then back on again within 1 seconds.

Color SplashTM 2G
Installation and
Operation Guide
COLOR SPLASH 2G REPLACEMENT MULTI-COLOR LED
IN-GROUND POOL AND SPA LIGHTS Model #s:
LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2
WARNING!
Permanent damage to the 12V AC lamp will
occur if installed on a 120V AC circuit.
DANGER!
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION
This device is not intended for use in anything
other than in-ground pools and spas.
1Rated Lamp Life
Safety Precautions
IMPORTANT NOTE: Color Splash 2G lights are recommended for
installation by a qualifed spa or pool professional. Color Splash lights
cannot be used with dimming systems. Doing so will void the warranty.
Attention: As part of your normal maintenance program, J&J Electronics
recommends that all light fixtures be inspected and replaced as necessary
to ensure proper operation of your Color Splash 2G lamps.
2
J&J ELECTRONICS, INC. 3-YEAR LIMITED WARRANTY
©2014 J&J Electronics, Inc. All rights reserved. ColorGlo and Color Splash are trademarks of J&J Electronics, Inc.
All registered and trademarked brands and names are the property of their respective companies.
REV.112514
7
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights offer a
variety of microprocessor controlled lighting effects that will instantly transform
your pool or spa into a color-rich paradise.
The illumination generated by the Color Splash 2G Replacement Multi-Color LED
Pool and Spa lights is based on Light Emitting Diode (LED) technology. The
average expected lamp life is rated up to 50,000 elapsed time hours under
normal operating conditions. [Temperature: -20°F to 110°F (-29°C to 43°C),
Humidity: 5-95% non-condensing].
• Do not open, service or tamper with any internal component of the Color
Splash Replacement Multi-Color LED In-ground Pool or Spa light. Doing so will
void the warranty. Follow each instruction in this owner’s manual and pay
careful attention to all warnings.
• Do not directly expose or immerse the Color Splash Replacement Multi-Color
LED In-ground Pool or Spa light in water without containing it in a proper
watertight light housing and niche assembly.
• Keep the pool or spa light dry.
• Handle the Color Splash Replacement Multi-Color LED In-ground Pool or Spa
light with care. Be careful not to drop the unit.
This owner’s manual contains important information on installing and using your
new Color Splash Replacement Multi-Color LED In-ground Pool or Spa light. Please
read it carefully and keep it in a safe place for future reference.
Color Splash 2G Replacement Multi-Color LED In-ground Pool and Spa lights are
available in 12V AC (low voltage) and 120V AC models as indicated on the product
packaging. Each light has a screw-in Edison base.
Always disconnect power to the pool or spa light at the circuit breaker panel before
attempting to service the light. Failure to do so could result in serious injury or death
due to electrical shock. Refer to the original manufacturer’s pool or spa installation
manual before proceeding. As with any electrical device, installation and service
should always be performed by a qualifed individual.
(For LPL-2030-12-2, LPL-2030-110-2, LPL-7030-12-2, LPL-7030-110-2)
J&J Electronics, Inc. (“J&J”) warrants the above-referenced model numbers of Color Splash 2G Multi-Color LED In-ground
Pool and Spa Lamp (the “Product”) to be free from defects in material and workmanship, under normal use, conditions and
service, for a period of three (3) years from the original date of purchase, subject to the terms specified herein. If during
the warranty period, the Product fails to operate due to a defect in material or workmanship, J&J will, at its option, repair
or replace the Product at no charge.
TERMS AND CONDITIONS
This warranty is available to the original purchaser of the product(s) only. This warranty applies only when products are
properly installed in an in-ground pool; any other use voids the warranty. Products must be used in lighting equipment
designed and approved for the application and in environmental conditions within the normal specified operating range.
This warranty does not apply to any abnormal use of product(s), use in violation of any applicable standard, code or
instructions for use in installations including those contained in the latest National Electrical Code (NEC), the Standards
for Safety of Underwriters Laboratory, Inc. (UL), Standards for the American National Standards Institute (ANSI). This
warranty will not apply in the event of conditions demonstrating abnormal use or stress, freezing, operating when not fully
submerged, under/over voltage/current conditions, excessive switching cycles or operating hours or outside the
recommended operating conditions. This warranty does not apply to color shifts or dimming caused by emissions and/or
LED color shifts and dimming that naturally occurs over time. Warranty conditions: If the product operates for 15 or
more hours per day or continuously for 24 hours per day, the product warranty period stated shall be reduced to half
the stated period. This warranty does not cover damage occurring during shipment, damage or failure resulting from
alteration, accident, acts of God, theft, abuse, negligent installation, improper service, unauthorized repairs, freezing or
where adequate care has not been taken to prevent damage to the product(s). Tampering with any internal component of
this product(s) will void the warranty.
This warranty gives you specific rights. You may have other rights that vary according to the laws of your state.
LIMITATION OF LIABILITY
THE FOREGOING SHALL CONSTITUTE THE EXCLUSIVE REMEDY OF THE PURCHASER AND IS IN LIEU OF ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, AND ALL WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OR TRADE. THE
LIABILITY OF J&J UNDER THIS WARRANTY SHALL BE LIMITED TO THE REPLACEMENT, REPAIR OR PRO-RATED CREDIT OF
THE PRODUCT(S) AS STATED HEREIN. J&J IS NOT RESPONSIBLE FOR SHIPPING OR TRANSPORTATION COSTS RELATED
TO OBTAINING WARRANTY SERVICE. IN NO EVENT SHALL J&J BE LIABLE FOR ANY OTHER COSTS OR DAMAGES,
INCLUDING LOST PROFITS OR REVENUES, LABOR CHARGES OR FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES.
J&J reserves the right to change the warranty, warranty period without prior notice and without incurring obligation.
To obtain warranty service, retain the failed Product; retain the installation invoice showing product purchase price and
contact J&J Electronics, Inc. at 800.735.4553 ext. 242 or [email protected]. As of 01/21/2014