COLORATO CLGH-42N User manual

www.colorato.net
INSTRUCTION MANUAL
GAS HEATER
CLGH-42N
READ INSTRUCTIONS CAREFULLY: READ AND FOLLOW ALL
INSTRUCTIONS. PLACE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE
REFERENCE. ONLY USE IN A WELL VENTILATED AREA.
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY. A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY
DAMAGE. PERSONAL INJURY OR LOSS OF LIFE.

1
TECHNICAL CHARACTERISTICS
Type : MOBILE GAS HEATER
Dimensions : 36*41*72 (D*W*H )
Category : I3B/P(30)
Pressure : 30mbar
Heater output : High : 4.2 kW
Mid : 2.9 kW
Low : 1.55 kW
Consumption : High : 305g/H
Mid : 210g/h
Low : 105g/h
Ignition system : Piezo electric
Injector size : 0.58 mm
Cylinder type : UP TO 15kg cylinders
WARNING:
1. THE APPARATUS IS NOT READY FOR THE PHYSICALLY WEAK, SLOW RESPONSE
OR MENTAL DISORDERS (INCLUDING CHILDREN) TO USE, UNLESS IT BEARS
RESPONSIBILITY FOR THE GUIDANCE OF SAFETY OR SAFE USE OF THE HELP
2. CHILDREN SHOULD BE MONITORED TO ENSURE THEY DO NOT PLAY APPARATUS
3. HEATER IS NOT LOCATED IMMEDIATELY BELOW A SOCKET-OUTLET
4. THIS HEATER IS NOT EQUIPPED WITH A DEVICE TO CONTROL THE ROOM
TEMPERATURE. DO NOT USE THIS HEATER IN SMALL ROOMS WHEN THEY ARE
OCCUPIED BY PERSONS NOT CAPABLE OF LEAVING THE ROOM ON THEIR OWN,
UNLESS CONSTANT SUPERVISION IS PROVIDED.

2
SAFETY PRECAUTIONS
1. Always use heater in accordance with
instructions supplied with each heater.
Keep instructions in a safe place.
2. DO NOT place clothes or other materials
on the heater. This could cause a fire risk
and/or affect the efficiency of the appliance.
3. DO NOT position heater close furniture. 4. DO NOT move heater from room to room when
lit.
5. DO NOT position heater close to walls,
furniture, net curtains, bed linen or any other
inflammable materials as this could result in the
risk of fire. The following minimum distances
should be respected; 50cm from side, 100 cm
from front. ALWAYS face heater towards center of
room. The heater should be positioned on a level
surface at all times.
6. If a leak is suspected, turn the gas off at the
cylinder. DO NOT disconnect the regulator. Check
all connections. Slowly turn the gas on and brush
the connections with soapy water or liquid
detergents a gas leak will form bubbles. If a leak is
found, turn the gas off. DO NOT use the heater
again until it has been checked by a competent
person in accordance with the Gas Safety
(installations and use) Regulations 1998

3
USING ENVIRONMENT
Your heater consumes oxygen while it is in function. For that reason, adequate ventilation
should be provided in rooms in which the heater is used. This ensures the removal of products
of combustion and allows the entry of replacement air.
Adequate ventilation should considerably reduce the possibility of condensation occurring.
REQUIRED VOLUME OF ROOM AND VENTILATION SURFACE:
VENTILATION SURFACE
VOLUME OF LIVING ROOM Low Level High Level
84 cubic meters 105cm2 105 cm2
IMPORTANT
1. Only use in well ventilated areas.
2. Do not use in vehicles, caravans or auto caravans.
3. Do not attempt to use in high-rise flats, basements, bathrooms or bedrooms.
4. Do not use your heater while sleeping.
5. Do not store flammable liquids or material near the heater.
6. Do not expose the gas bottle to the full summer heat nor too near any other heat source.
7. Do not place a heater in use near curtains, furniture, wood paneling or combustible material
which can deteriorate with heat.
8. While in use, ensure that children do not approach the heater.
9. Do not move the appliance when in use; the safety device may be activated by knocks or
movement.
10. This appliance should be tested for leaks before initial use and whenever the cylinder is re-
connected.
11. It is important that all gas connections have been correctly made to prevent any leakage.
Do not use naked flame to test for leaks. Call your supplier to ask suport.
12. Always use your cylinder always in an upright position.
13. Always turn off the regulator control when the heater is not in use.
3

4
14. When lighting your heater for the first time or after a period of time has passed since the
last use, light the heater outside and burn outdoors for 15 minutes.
15. The guard on the appliance is to prevent risk of fire or injury form burns and no part of it
should be permanently removed. It does not give full protection for young children or the
infirm. We would recommend a fireguard to be fitted.
16. This appliance is indoor use only.
17. Do not handle the appliance with wet hands.
CONSTRUCTION AND FUNCTION
1. Igniter
2. Gas control knob
3. Gas burner safety guard
4. ODS System
5. Rear cover
6. Vent
7. Quartz heating element
CONNECTING THE CYLINDER
1. Place the gas filled cylinder into the back of the heater
2. Clip on the gas regulator to the gas cylinder
3. Turn the regulator on.
4. Where the regulator is not supplied please contact your gas dealer to advise of correct type
for the gas cylinder being used.
5. IMPORTANT TEST FOR LEAKS:
This must be carried out in a well-ventilated area, free from naked flames and any other
3
4
5
1
2
6
7

5
sources of ignition. With the regulator connected to the cylinder turn on the regulator control.
Brush all hose connections, pipe connections to the valve and gas cylinder valve with a 50:50
solution of detergent and water. A stream of bubbles forming indicates a leak. If a leak is
found turn off at the regulator and disconnect the regulator from the bottle and remove the gas
cylinder outdoors or to a well ventilated area. Contact your gas supplier for assistance. DO
NOT USE THE HEATER.
6. After leak testing is satisfactorily carried out close the back door of the heater. It may be
necessary to move the heater slightly to allow the regulator and hose to fit in the back without
kinking the hose
HOW TO CHANGE A CYLINDER
(a) Unplug the heater before take out the cylinder.
(b) Turn off at the regulator and allow the heater to cool fully before removing and replacing the
cylinder. Do not attempt to replace the cylinder whilst the heater is still running.
(c) Cylinders must be replaced in a flame free environment.
(d) Do not smoke while changing the cylinder.
(e) When you need to replace your empty cylinder, turn the gas off at the valve or regulator of
the cylinder and take the empty cylinder out of the heater.
(f) Remove the regulator from the empty cylinder.
(g) Following the steps described under “connecting the cylinder”, connect a new cylinder
GAS HEATER OPERATION GUIDE
Pos. 1 (lighting) Pos. 2 (min.)
Pos. 3 (mid) Pos. 4 (max)
1. LIGHTING INSTRUCTION
A. The heater has three settings. Lighting(Pos.1) and Minimum (Pos.2); Medium (Pos.3) and
Maximum (Pos.4)
B. Place the gas filled cylinder into the back of the heater.
Clip on the gas regulator to the gas cylinder.
Turn on the gas regulator.
2. LIGHTING
Press the control button for 10 seconds at the Position 1, at the same time press the piezo
igniter key to lit with thumb finger of left hand, Continue this procedure until pilot ignites,
approximately after 20 seconds leave control button. At this stage if the pilot is alight, it means

6
that the heater is at the minimum position (Pos.1). If the pilot flame goes out please repeat this
procedure.
3. HEAT SETTINGS
To change from minimum to maximum gently press control button and turn it to position 3.
To change from maximum to medium gently press control button and turn it to position 2.
4. TURN OFF THE HEATER
Turn off heater by turning the valve of the cylinder and turn the switch of the heater to the
“OFF” position (Pos 1), If the heater is not used for a period of time, disconnect the regulator
from the cylinder and replace any value protection plug or cover.
WARNING
1. Read the instructions before using this appliance.
2. The apparatus is not ready for the physically weak, slow response or mental disorders
(including children) to use, unless it bears responsibility for the guidance of safety or safe
use of the help.
3. Children should be monitored to ensure they do not play apparatus.
4. Never attempt to light if the hose is loose or damaged in any way.
5. Do not press the ignition button for more than 40 seconds.
6. Never disconnect the regulator while cylinder valve or regulator is open.
7. Do not change cylinders in areas in which open fire exists.
8. Do not expose your cylinder to extreme heat.
9. Do not store any other cylinders in the room in which your heater is used.
10. Do not insert your finger or any other material through the front panel of the heater.
11. Leave at least 1 meter distance between your heater and the other heat source.
12. Do not let unauthorized persons to tamper with your heater.
13. Do not place appliance under electrical socket outlets.
14. Do not use the heater in bathrooms, shower of swimming pool, or leisure vehicles such as
caravans or auto caravans.
15. This heater must not be used without a gas cylinder fitted for stability purposes.
16. Do not cover your heater. Fabrics, clothing, hangings, net curtains, bed linens and other
flammable materials may ignite if placed against the outlets of your heater.
17. In the event of leakage, the appliance should be turned off at the regulator switch-on valve
and the regulator disconnected from the cylinder.
18. After use turn off the appliance at the gas container valve.
19. Only use in a well ventilated area.

7
STORAGE
1. Disconnect cylinder.
2. Store cylinder in a well-ventilated area away from combustible material. Storage preferable
be in an outhouse but must not be in a basement or high-rise flat.
3. The heater should be covered in a dry, dust-free area in its original packaging.
CLEANING
1. Make sure you have disconnected the heater before cleaning.
2. Turn of your gas supply at the regulator.
3. Use a damp soapy wrung cloth clean the exterior and cylinder storage area of your heater.
4. Make sure that no water gets onto the burners or pilot/light area. Wipe the heater dry
before use.
5. Don’t use abrasive cleaners as they may damage the quality paint finish.
MAINTENANCE
1. Check flexible tubing between regulator and heater regularly and replace if perished, worn
or damaged. In any case replace tubing taking into consideration the expiration date.
2. It is recommended that the heater be serviced every year by a competent person in
accordance with the Gas Safety (installations and use) Regulations 1998.
3. If any parts need replacing, they should be replaced only with the correct parts supplied by
the original manufacturer.

8
FAULT FINDING CHART
For your safety purpose, call local service center if you have problems.
REPAIRS SHOULD ONLY BE CARRIED OUT BY A COMPETENT PERSON IN
ACCORDANCE WITH THE GAS SAFETY (INSTALLATIONS AND USE) REGULATIONS
1998
Problem Problem Causes What To Do
Regulator & hose
connection loose
Valve & pipe
connection loose
Pipe broken
Use soap form for leakage control, check all
connection system replace defected parts
Smell of gas
Missing piece of
ceramic fireclay
Inspect perimeter of each plaque and locate place
where some fireclay has been displaced. Repair
with PYRUMA and leave to set for Approx. 48
hours.
Inefficient
combustion on
ceramic burner
Dirty gas inlets Please clear injectors with Air
Battery no power Change a AAA battery
Defective Spark -
Plug
Check cable of igniter, & replace defected igniter if
necessary
If there is no
ignition
Defective igniter cable Check spark – plug and connections, & replace
defected igniter if necessary
Run out of gas Change the gas bottle
Thermal element has
not been warm
enough
Try restarting
Wing or draught has
extinguished the
flame
Put the appliance out of reach of wind and draught,
let it cool down for a couple of minutes and try to
restart it
Faulty thermocouple Replace the faulty thermocouple
Technical
problems
Burner flame
has extinguish
during operation
Faulty magnetic valve Replace the magnetic valve
Heater is not
remain alight
when pressure
is released from
ignition button
Wrong power setting
at first process
Turn the control knob at “ START” Position and
press for 10 seconds, whilst press the Piezo igniter
key to lit
Did not connect the
gas regulator to gas
cylinder
Connect heater to the gas cylinder and ensure there
is not smell, then follow the Instruction to turn on the
heater
general
problem
Heater could not
be turned on
Gas cylinder control is
closed Please turn on the gas cylinder control