ColorDMD CHROMA eDP WPC95 User manual

8-Pin DMD Power Cable
( Remove entire cable
from the game )
14-Pin DMD Ribbon Cable
(Unplug cable from DMD
and leave other end
connected to game)
Figure A
Carefully remove the translite from the backbox and then lower
the speaker panel to the position shown in Fig. A to gain access
to the backbox.
Installation Instructions
for WPC95 - CHROMA eDP
Be sure to turn OFF the power to the pinball machine before
installing the ColorDMD display.
Tools Required
: Phillips Screwdriver
Remove and save all four DMD mounting screws. Remove the
original DMD from the game and store it in a safe place.
1
2
3
STEP
STEP
STEP
!
Disconnect the DMD power and ribbon cables from the DMD.
Unplug the DMD power cable from the high-voltage A/V board
J-604 (see Fig. E), and remove this cable from the backbox .
Congratulations on the purchase of a new ColorDMD display. The ColorDMD
will enhance your pinball machine by introducing
color to the dot matrix
display graphics produced by the game.
•
ALL RIGHTS RESERVED - US PATENT 8,773,452 B2 - COPYRIGHT 2016 - COLORDMD DISPLAYS LLC

Figure B
PWR
DMD_IN
USB Port
Figure C
WPC95
Mounting
Holes
WPC95
Mounting
Holes
To protect against electrical shock,
ground wire from the backbox must
be connected to this metal bracket.
Ground wire
attached here
Position the ColorDMD face down in the orientation shown in
Fig. B on the speaker panel and align the four WPC95 mounting
holes (see Fig. C).
Remove the protective film from the front side of the new
ColorDMD display.
Use the four original DMD screws from Step 3 to fasten the
ColorDMD display to the speaker panel. If one of the screws is
attached to the ground wire from the backbox, ensure that the
ground wire is making good contact with the ColorDMD metal
bracket (see Fig. C).
4
5
6
STEP
STEP
STEP
!
WARNING - ELECTRIC SHOCK
WARNING . Electric Shock Hazard - To protect against
accidental electric shock, DO NOT operate the game without
ensuring that the ColorDMD metal bracket is electrically grounded.
ALL RIGHTS RESERVED - US PATENT 8,773,452 B2 - COPYRIGHT 2016 - COLORDMD DISPLAYS LLC

Plug Into
Power Driver
Board J-138
(B.B.)
Optional :
Only use the male-to-male
adapter to reconnect a
pre-existing cable back
into J-138
Plug Into
ColorDMD
PWR
J-604
J-603
A/V Board
Power Driver Board
Route the new ColorDMD
Power Cable along with
the existing cables for a
clean install.
Figure E
J-138
Locate the included 4-pin ColorDMD power cable. One end of the
cable has a single connector (see Fig. D). Plug this connector
into the PWR header (see Fig. C) on the ColorDMD.
Plug the other end of the new ColorDMD Power Cable (see Fig. D)
into J-138 on the WPC95 Power Driver Board (see Fig. E). If an
existing cable is currently plugged into J-138, disconnect it before
connecting the ColorDMD power cable
.
If you disconnected a cable from J-138 in the previous step, use
the included male-to-male adapter to re-connect this cable to the
available center connector on the ColorDMD cable (see Fig. D).
Otherwise, do not connect the male-to-male adapter and store it
in a safe place.
7
8
Figure D
9
STEP
STEP
STEP
TIP
ALL RIGHTS RESERVED - US PATENT 8,773,452 B2 - COPYRIGHT 2016 - COLORDMD DISPLAYS LLC

Red Stripe on the
14-Pin Ribbon Cable
Enter ColorDMD Menu /
Advance to Next Menu Item
Toggle Selection Up /
Confirm Menu Exit
Toggle Selection Down
Return to Previous Menu Item /
Initiate USB Download
(Press for 5 Seconds)
Plug the 14-Pin ribbon cable into DMD_IN on the ColorDMD with
the red stripe nearest the 4 push-buttons (see Fig. F). The
other end of this cable should still be plugged into J-603 on the
A/V Board with red stripe on the left-hand side (see Fig. E).
10
Figure F
STEP
!
Locate and press the right-most ColorDMD Menu button (See Fig. F)
to customize the display settings. Continue pressing the button to
advance to the "MOUNTING" menu. Next use the Toggle Selection Up
button to change the setting to "WPC95".
12
STEP
Double check for proper alignment of all cable connections.
For additional information regarding display settings please visit
our website at www.colordmd.com .
STEP
STEP
Press the right-most button to advance to the "EXIT AND SAVE"
menu. Press the Confirm Menu Exit button to save settings and
return to game mode. Video should appear on the new ColorDMD
Display. Visit ColorDMD website to download game specific color
ROM file and install using USB thumb drive. Have fun!
13
11
While ensuring no wires get pinched, raise the speaker panel
and turn on the pinball machine.
ALL RIGHTS RESERVED - US PATENT 8,773,452 B2 - COPYRIGHT 2016 - COLORDMD DISPLAYS LLC