Colors CK1-G1D-B4A User manual
Ultrathin Touch Wheel RF Remote Controller
Page 1
User Manual Ver
1.1.1
1 zone dimming/Touch brightness wheel/Wireless remote 30m distance/CR2032
battery
Features
●
Apply to sin gle color LED controller.
●
Ultra sensitive color adjustment touch wheel.
●
Each remote can match one or more receiver.
●
CR2032 battery powered.
●
Operate with LED indicator light.
Note: Before the first use,
please remove the
protective film on the
battery.
Back
holder
To fix the remote, two options are offered for
selection:
Option 1:
fix the remote' back holder on the wall with two
screws. Option 2:
adhere the remote' back holder to the wall with
paster.
Technical
Parameters
LVD RED
Note: If the LED indicator is not on when press key,
it is due to dead battery or bad contact caused by multiple
plugging, please replace the battery, or raise the battery
shrapnel with a screwdriver.
Operation
●
When light is on, touch the color wheel, the indicator will display red.
●
To extend battery life, no touch or press key operation after a few seconds,
the touch wheel will enter sleep state, you need press any key to make touch wheel quit sleep state.
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Mechanical Structures and Installations
9mm
Use the controller’s Match key
Match:
Short press match key, immediately press
on/off key (single zone remote) or zone key
(multiple zone remote) on the remote.
The LED indicator fast flash a few
times means match is successful.
Delete:
Press and hold match key for 5s to delete all
match,
The LED indicator fast flash a few
times means all matched remotes we.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat
again. Immediately short press on/off key (single zone
remote)or zone key (multiple zone remote) 3 times on
the remote. The light blinks 3 times means match is
successful.
.Delete:
Switch off the power, then switch on power, repeat
again. Immediately short press on/off key (single zone
remote)or zone key (multiple zone remote) 5 times on
the remote. The light blinks 5 times means all matched
remotes were deleted.
Model No.: CK1-G1D-B4A
Ultrathin Touch Wheel RF Remote Controller
5 years
Warranty
Warranty
CR2032
Battery
58.5mm
58.5mm
107mm
63.00 mm
68.00 mm
37.00 mm
Input and Output
Output signal
RF(2.4GHz)
Working voltage
3VDC(CR2032)
Working current
＜5mA
Standby current
＜10μA
Standby time
1 year
Remote distance
30m(Barrier-free space)
Safety and EMC
EMC standard (EMC)
ETSI EN 301 489-1 V2.2.3
ETSI EN 301 489-17 V3.2.4
Safety standard(LVD)
EN 62368-1:2020+A11:2020
Radio
Equipment(RED)
ETSI EN 300 328 V2.2.2
Certification
CE,EMC,LVD,RED
Environment
Operation
temperature
Ta :
-3 0
O
C
~
+5 5
O
C
IP rating
IP20
Weight
Net weight
0.037 kg
Gross weight
0.062kg
Ultrathin Touch Wheel RF Remote Controller
Page 2
User Manual Ver
1.1.1
Safety
information
1. Read all instructions carefully before you begin this installation.
2. When installing battery, pay attention to the battery positive and
negativ e polari ty. A long time without the remote control, remove the
battery.
When remote distance becomes smaller and insensitive, replace the battery.
3. If no response from the receiver, please re-match the remote.
4. Gently handle remote, beware offalling.
5. For indoor and dry location use only.
Key
function
●
Remote Introduce
3 Scene
Bright
wheel
On/Off
50%
Bright-
Bright+
Mode
1%
100%
On/Off: Turn on/off light.
Bright wheel: Touch to change brightness.
Bright+/-: Adjust brightness, short press 10 levels, long press 1-6s for continuous 256 levels
adjustment.
Mode:100%,75%,50%,25%: Get 4 kinds brightness directly.
3 Scenes: Brightness memory. Short press recall the scene, long press 2s save
the current state into the scene. the LED indicator will light up longer when
save OK.
