Comax AL100 Product guide
Unit Type Code Nominal
Voltage
Voltage
Range
Nominal
Sounder
Current*
Nominal SPL Max SPL Average SPL
Nominal
Beacon
Current*
AL100.012.2 12 V dc 11.5-14V dc 17mA
101.6dB(A)
Tone 44 @ 1m
110dB(A)
Tone 4 @ 1m
102.3dB(A) All
tones @1m
341mA
24V dc 33.5mA AL100.024.2 250mA 20-28V dc
48V dc 113mA AL100.048.2 170mA 42-52V dc
24-28V ac
50/60Hz
AL100.024.7 24V ac 42.5mA 300mA
AL100.048.7 48V ac 42mA 250mA
48V ac ±
10% 50/60Hz
AL100.115.7 115V ac 25mA 70mA
115V ac ±
10% 50/60Hz
230V ac 17mA AL100.230.7 35mA
230V ac ±
10% 50/60Hz
*Nominal current at nominal voltage, Tone 12 / 1Hz Flash Pattern
0.4Nm
5mm
0.5 2.5mm
• -40°C to +66C (-40°F to 151°F)
• Type 3R / 13 (IP66, Independently tested to EN60529:1991)
• 0.46Kg (1.01lb)
• CE, AL100XDC024 CPR compliant, All units UL Listed.
Attention: Installation must be carried out by an electrician in compliance with the latest codes and regulations.
Attention: L'installation doit être effectuée par un électricien conformément aux derniers codes et réglementations.
Achtung: Die Installation muss von einem Elektriker gemäß den neuesten Vorschriften und Bestimmungen durchgeführt werden.
Attention: Disconnect from power source before installation or service to prevent electric shock
Attention: Débranchez-le de la source d'alimentation avant l'installation ou l'entretien pour éviter tout choc électrique.
Achtung: Vor Installation oder Wartung von der Stromquelle trennen, um einen Stromschlag zu vermeiden.
AC: 1.0 – 2.5mm2 / AWG18 – AWG12
DC: 0.2 – 2.5mm2 / AWG24 – AWG12
Comax Industrielle Signaltechnik AG, CH-4712 Laupersdorf www.comax.ch Installationsanleitung_AL100_Rev2_19_07_2021
Installation/Anschluss
Installation/Raccordement
Installation/Connection AL100
DC
(See D218-06-201)
AC
(See D218-06-205)
- + - +
A
B
C
E N L
E N L
+ + - - S2 S3
S2 S1
S2
S1
N L
+-
E E S3 S2 N/- L/+
Default = S2 - Tone 1 Default = S1 - Tone 44
(ON = 1, OFF = 0)
(AC & DC, See D221-95-001)
A
B
C
A
B
C
A
B
C
A
B
C
A
B
C
(DC Only)
(DC Only)
(Not CPR Compliant)
(Not CPR Compliant)
1Hz
1.5Hz
2x
INSTRUCTION & SERVICE MANUAL
AL100
4x
1Nm
<ø20mm
98 3,86in.
35,9 1,41in.
35,9 1,41in.
60,3 2,37in.
Construction Product Regulation
AL100.024.2 & AL100.048.2 are compliant to EN54-3:2001+A1+A2 & EN54-23:2010
VAD for use in fire detection and fire alarm systems installed in and around buildings
Alarm devices – Sounder & Beacon
Type 3R / 13, IP66, Independently tested to EN60529:1991, (IP33C Compliant to EN54-3)
Type B Product, For Indoor & Outdoor use
Observe Precautions for handling electrostatic devices
-25°C to +55°C compliant to EN54-3 & EN54-23
Cable Glands must be suitably sealed and meet minimum IP33 for EN54-3 applications
Storage Temperature: -40°C to +70°C
Maintenance – None
Units can be mounted using the 2 of the 4-off ø6mm holes or through the back of the
housing using the supplied gasket
Approved Tones for EN54-3 Applications:
•(Alternating Tone) 800/1000Hz @ 2Hz Alternating Tone 44
•(Rising Tone) 500/1200Hz @ 0.26Hz (3.3s on, 0.5s off) Tone 8
•(Fainting Tone) 1200/500Hz @ 1Hz Tone 2
•(Continuous Tone) 800Hz Tone 21
•(Pulsed Tone) 660Hz (150mS on, 150mS off) Tone 31
•(Alternating Tone) 544Hz(100mS)/440Hz (400mS) Tone 5
2821
S36282
21
Order Code: AL100.024.2
Voltage Range: 20-28Vdc
Nominal Voltage: 24Vdc
Max Sounder Current: P1: 125mA @ 28Vdc
Max Beacon Current: 271mA @ 20Vdc
DP-2821-CPR-0109
2821
S36282
21
Order Code: AL100.048.2
Voltage Range: 42-52Vdc
Nominal Voltage: 48Vdc
Max Sounder Current: 125mA @ 52Vdc
Max Beacon Current: 160mA @ 42Vdc
DP-2821-CPR-0109
AL100.024.2 / AL100.048.2 @ 1m
Horizontal Sound Output Max Voltage
(60 Vdc) LAFmax,T dB(A)
Horizontal Sound Output
Min Voltage (18 Vdc) LAFmax,T dB(A)
Angle Tone
44
Tone
8
Tone
2
Tone
21
Tone
31
Tone
5
Tone
44
Tone
8
Tone
2
Tone
21 Tone 31 Tone 5
15° 98 99.9 99 95.7 94.8 95.4 94.7 96.8 95.9 93 91.9 92.7
45° 97.8 100.1 99 97.6 94.7 96.6 95 97 96 94.8 92.1 94
75° 101.5 102.9 102.4 101.4 98.3 100.4 98.7 100.2 99.5 98.8 94.9 97.9
105° 101.4 102.8 102.5 101.4 98.1 100.4 98.6 100.2 99.5 98.8 94.9 97.9
135° 97.4 100 98.9 97.2 94.9 96.4 94.6 96.9 95.9 94.5 92.2 93.8
165° 97.5 99.6 98.9 95.8 94.7 95.4 94.3 96.4 95.8 93 91.8 92.8
Vertical Sound Output Max Voltage
(60 Vdc) LAFmax,T dB(A)
Vertical Sound Output Min Voltage
(18 Vdc) LAFmax,T dB(A)
Angle Tone
44
Tone
8
Tone
2
Tone
21
Tone
31
Tone
5
Tone
44
Tone
8
Tone
2
Tone
21 Tone 31 Tone 5
15° 96.3 99.8 99 95.5 94.1 95.3 93.1 96.7 96 92.8 91.2 92.6
45° 97.6 99.9 98.8 97.4 94.5 96.3 94.8 96.8 95.7 94.6 91.9 93.8
75° 101.3 103 102.5 101.4 98.1 100.5 98.5 100.1 99.5 98.7 95 97.8
105° 101.3 102.8 102.4 101.3 98.2 100.5 98.5 100.1 99.5 98.7 95 97.7
135° 97.4 99.9 98.8 97.6 94.5 96.3 94.6 96.8 95.8 94.8 91.9 93.7
165° 96.7 100 99 95.5 93.9 95.4 93.6 96.9 96 92.7 91.1 92.7
E2S Warning Signals Impress House, Mansell Road, Acton, London W3 7QH sales@e2s.com e2s.com D218-00-201-IS Issue 1 27/05/2021
INSTRUCTION & SERVICE MANUAL
AL100
• All models are approved for use as Audible Signal and Visual Appliance
for use as General Signaling: UL464A & CSA C22.2 No 205-17
• Type 4 / 4X / 3R / 13, IP66 independently tested to EN60529:1991
• -40°C to +66°C / -40°C to +151°F
General Signaling Canada:
AL100.xxx.2 DC: -40°C to +55°C / -40°F to +131°F
AL100.xxx.7 AC: -40°C to +40°C / -40°F to +104°F
• To maintain Ingress Protection, cable entries must be fitted with suitably rated cable glands or stopping plugs
• Mounting - Units can be mounted using 2 of the 4-off ø6mm holes in the mounting lugs or through the back of the housing using the
supplied gasket.
• EOL Monitoring (DC Only): End of Line Devices may be fitted between the +ve & -ve terminals of the PCBA. Please ensure that the device
legs meet the wire size range stated for the connection terminals and are fitted correctly in order to avoid a short. Refer to the compatible
control panel specification for EOL device values and ratings
Model Nominal
Voltage Voltage Range
Nominal Operating Current* Max Operating RMS#
Beacon Sounder Beacon Sounder
AL100.012.2 12V dc 11.5-14Vdc 341mA 17mA 531mA
125mA AL100.024.2 24V dc 20-28Vdc 250mA 33.5mA 271mA
AL100.048.2 48V dc 42-52Vdc 170mA 113mA 170mA
AL100.024.7 24V ac 24-28Vac 50/60Hz 300mA 42.5mA 426mA
42.5mA
AL100.048.7 48V ac 42-54Vac 50/60Hz 250mA 42mA 360mA
AL100.115.7 115 Vac 103.5-126.5Vac
50/60Hz 70mA 25mA 101mA
AL100.230.7 230 Vac 207-253Vac
50/60Hz 35mA 17mA 58mA
*Nominal Voltage, 1Hz Flash Pattern & Tone 12; #Worst-case input voltage and worst case flash pattern
floor area covered by the VAD.
maximum length of the sides of the square
mounting height from the floor and y is the
Wall mounted, where x is the maximum
Category W-x-y (Wall mounted): V=55.3m³
V=62.5m³
11W
Power
14W
Note: CPR aproved units must be
positioned sounder on top,
beacon below.
table are VdS Approved)
(Only units in the following
Coverage Area According to EN54-23
Category W
Unit
W-2.4-4.8
W-2.5-5
x
y
y
Approved Beacon for EN54-23 Applications:
Clear lenses are compliant with EN54-23
Attention: Installation must be carried out by an electrician in compliance with the National Electrical Code, NFPA 70 or CSA 22.1 Canadian Electrical
Code, Part I, Safety Standard for Electrical Installations, Section 32. / L'installation doit exclusivement être réalisée par du personnel qualifié, conformé
ment au code national d'électricité américain, NFPA 70 ou CSA 22.1 Code canadien de l'électricité, première partie, norme de sécurité relative aux
installations électriques, Section 32
AL100.024.2 & AL100.048.2 LIGHT OUTPUT
AL100.024.2
AL100.048.2
ALERTALARM RANGE
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78
6
5
D
C
134
2
A
B
D218-06-201
R.S.RAIT
B.ISARD
R.N.POTTS
OF
AL100X, AL105 & DL105 DC COMBINED
SOUNDER & XENON WIRING DIAGRAMS
NTS 1
WIRING LINKING BEACON & SOUNDER
FACTORY FITTED
2
-
+
-
+
-
+
R1
+
-
-
+
R1
+
-
-
+
S2
S3
R1
+
-
-
+
S2
OPTIONAL LINE MONITORING RESISTOR, CUSTOMER SUPPLIED,
14V MAX SYSTEM = 120Ω MIN, 2W MIN OR 1KΩ MIN, 0.5W MIN
28V MAX SYSTEM = 470Ω MIN, 2W MIN OR 2.4KΩ MIN, 0.5W MIN
RECOMMENDED MINIMUM VALUES:
R1
Stage 1 +ve IN
Stage 1 +ve OUT
Stage 1 -ve IN
Stage 1 -ve OUT
Single Stage Configuration Config.: 1a
Line Monitoring
Stage 1: Apply Power to Stage 1 +ve & Stage 1 -ve
Two Stage Configuration Config.: 1b
Common Negative
Stage 1: Apply Power to Stage 1 -ve & Common +ve
Stage 2: Apply Power to Stage 1 -ve, Stage 2 -ve & Common +ve
Three/Four Stage Configuration Config.: 1c
Common Negative
Stage 1: Apply Power to Stage 1 -ve & Common +ve
Stage 2: Apply Power to Stage 1 -ve, Stage 2 -ve & Common +ve
Stage 3: Apply Power to Stage 1 -ve, Stage 3 -ve & Common +ve
Stage 4: Apply Power to Stage 1 -ve, Stage 2 -ve, Stage 3 -ve &
Common +ve
Linked Sounder & Beacon Activation (Default)
16/03/2021
INTRODUCTION
A
16/03/2021
16/03/2021
MOD No. REASON - INITIAL - DATEISSUE
+
-
+
-
+
-
+
-
+
-
+
-
Common +ve IN
Common +ve OUT
Stage 1 -ve IN
Stage 1 -ve OUT
Stage 2 -ve
Common +ve IN
Common +ve OUT
Stage 1 -ve IN
Stage 1 -ve OUT
Stage 2 -ve
Stage 3 -ve
RSR - 11/05/2021
ALERTALARM RANGE
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78
6
5
D
C
134
2
A
B
R.S.RAIT
B.ISARD
R.N.POTTS
OF
NTS
Stage 1 +ve IN
Stage 1 +ve OUT
Stage 1 -ve IN
Stage 1 -ve OUT
-ve IN
+ve IN
D218-06-201
2
2
R2
-ve OUT
+ve OUT
R1
+
-
-
+
R1
+
-
-
+
S2
R1
+
-
-
+
S2
S3
OPTIONAL LINE MONITORING RESISTOR, CUSTOMER SUPPLIED,
14V MAX SYSTEM = 120Ω MIN, 2W MIN OR 1KΩ MIN, 0.5W MIN
28V MAX SYSTEM = 470Ω MIN, 2W MIN OR 2.4KΩ MIN, 0.5W MIN
RECOMMENDED MINIMUM VALUES:
R1
Single Stage Configuration Config.: 5a
Line Monitoring
Stage 1: Apply Power to Stage 1 +ve & Stage 1 -ve
Two Stage Configuration Config.: 5b
Common Positive
Stage 1: Apply Power to Stage 1 -ve & Common +ve
Stage 2: Apply Power to Stage 1 -ve, Stage 2 -ve & Common +ve
Three/Four Stage Configuration Config.: 5c
Common Positive
Stage 1: Apply Power to Stage 1 -ve & Common +ve
Stage 2: Apply Power to Stage 1 -ve, Stage 2 -ve & Common +ve
Stage 3: Apply Power to Stage 1 -ve, Stage 3 -ve & Common +ve
Stage 4: Apply Power to Stage 1 -ve, Stage 2 -ve, Stage 3 -ve &
Common +ve
Independent Sounder & Beacon Activation (Remove Link Wires)
16/03/2021
INTRODUCTION
A
16/03/2021
16/03/2021
MOD No. REASON - INITIAL - DATEISSUE
-ve IN
+ve IN
R2
-ve OUT
+ve OUT
-ve IN
+ve IN
R2
-ve OUT
+ve OUT
SOUNDER & XENON WIRING DIAGRAMS
AL100X, AL105 & DL105 DC COMBINED
Common +ve IN
Common +ve OUT
Stage 1 -ve IN
Stage 1 -ve OUT
Stage 2 -ve
Common +ve IN
Common +ve OUT
Stage 1 -ve IN
Stage 1 -ve OUT
Stage 2 -ve
Stage 3 -ve
RSR - 11/05/2021
ALERTALARM RANGE
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
MOD No. REASON - INITIAL - DATEISSUE
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78
6
5
D
C
134
2
A
B
D218-06-205
R.S.RAIT
B.ISARD
R.N.POTTS
OF
SOUNDER & XENON WIRING DIAGRAMS
NTS 1
SWITCHES FOR STAGE OPERATION
CUSTOMER SUPPLIED
WIRING LINKING BEACON & SOUNDER
FACTORY FITTED
2
Single Stage Configuration Config.: 1a
Stage 1: Apply Power to Stage 1 Live & Stage 1 Neutral
Linked Sounder & Beacon Activation (Default)
Three/Four Stage Configuration Config.: 1b
Stage 1: Apply Power to Live & Neutral
Stage 2: Apply Power to Live & Neutral & connect Stage 2 to Live
Stage 3: Apply Power to Live & Neutral & connect Stage 3 to Live
16/03/2021
INTRODUCTION
RSR - 16/04/2021
A
16/03/2021
16/03/2021
N
L
E
N
L
E
Stage 1 Live IN
Stage 1 Live OUT
Stage 1 Neutral IN
Stage 1 Neutral OUT
Earth
Earth
N
N
L
L
E
E
N
L
E
N
L
E
Live IN
Live OUT
Neutral IN
Neutral OUT
Earth
Earth
N
N
L
L
E
E
Stage 2
Stage 3
S2
S3
AL100X, AL105 & DL105 COMBINED
ALERTALARM RANGE
C
THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE
MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND
IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY
SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY
BE DISCLOSED, LOANED, COPIED OR USED FOR
MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR
WRITTEN CONSENT.
EUROPEAN SAFETY SYSTEMS LTD.
AS PER LATEST DATE OF ISSUE SHOWN ABOVE
DRAWING TO BS8888:2000
GEOMETRIC TOLERANCES TO ISO1101:1983
LINEAR DIMENSIONAL TOLS
ANGULAR DIMENSIONAL TOLS
STANDARDS
MOD No. REASON - INITIAL - DATEISSUE
DATE
APPROVED
CHECKED DATE
DATE
DRAWN WEIGHT (Kg)
SURFACE FINISH
MATERIAL
ALTERNATIVE MATERIAL SHEETSCALE
TITLE
A3
IF IN DOUBT, ASK -
DO NOT SCALE
ALL DIMENSIONS IN MM
DRAWING NUMBER
A
B
C
D
E
F
G
109
G
F
E
78
6
5
D
C
134
2
A
B
D218-06-205
R.S.RAIT
B.ISARD
R.N.POTTS
OF
NTS 2
SWITCHES FOR STAGE OPERATION
CUSTOMER SUPPLIED
2
Single Stage Configuration Config.: 2a
Stage 1: Apply Power to Stage 1 Live & Stage 1 Neutral
Independent Sounder & Beacon Activation (Remove Link Wires)
Three/Four Stage Configuration Config.: 2b
Stage 1: Apply Power to Live & Neutral
Stage 2: Apply Power to Live & Neutral & connect Stage 2 to Live
Stage 3: Apply Power to Live & Neutral & connect Stage 3 to Live
16/03/2021
INTRODUCTION
RSR - 16/04/2021
A
16/03/2021
16/03/2021
N
L
E
N
L
E
Stage 1 Live IN
Stage 1 Live OUT
Stage 1 Neutral IN
Stage 1 Neutral OUT
Earth
Earth
N
N
L
L
E
E
N
L
E
N
L
E
Earth
Earth
N
N
L
L
E
E
Stage 2
Stage 3
S2
S3
Live IN
Live OUT
Neutral IN
Neutral OUT
AL100X, AL105 & DL105 COMBINED
SOUNDER & XENON WIRING DIAGRAMS
1000Hz PFEER Toxic Gas
1200/500Hz @ 1Hz DIN /PFEER P.T.A.P.
1000Hz @ 0.5Hz(1s on, 1soff) PFEER Gen. Alarm
1.4KHz-1.6KHz 1s, 1.6KHz-1.4KHz 0.5s NF C 48-265
544Hz(100mS)/440Hz (400mS) NF S 32-001
1500/500Hz - (0.5s on , 0.5s off) x3 + 1s gap AS4428
500-1500Hz Sweeping 2 sec on 1 sec off AS4428
500/1200Hz @ 0.26Hz (3.3son, 0.5s off) Netherlands -
NEN 2575
1000Hz (1s on, 1s off)x7 + (7s on, 1s off) IMO Code 1a
1000Hz (1s on, 1s off)x7 + (7s on, 1s off) IMO Code 1a
420Hz(0.5s on, 0.5s off)x3 + 1s gap ISO 8201 Temporal
Pattern
1000Hz(0.5s on, 0.5s off)x3 + 1s gap ISO 8201 Temporal
Pattern
422/775Hz - (0.85 on, 0.5 off) x3 + 1s gap NFPA -
Temporal Coded
1000/2000Hz @ 1Hz Singapore
300Hz Continuous
440Hz Continuous
470Hz Continuous
500Hz Continuous IMO code 2 (Low)
554Hz Continuous
660Hz Continuous
800Hz IMO code 2 (High)
1200Hz Continuous
2000Hz Continuous
2400Hz Continuous
440Hz @0.83Hz (50
cycles/minute) Intermittent
470Hz @0.9Hz - 1.1s Intermittent
470Hz @5Hz - (5
cycles/second) Intermittent
544Hz @ 1.14Hz - 0.875s Intermittent
655Hz @ 0.875Hz Intermittent
660Hz @0.28Hz - 1.8sec
on, 1.8sec off Intermittent
660Hz @3.34Hz - 150mS
on, 150mS off Intermittent
745Hz @ 1Hz Intermittent
800Hz - 0.25sec on, 1 sec off Intermittent
800Hz @ 2Hz IMO code 3.a
(High) Intermittent
1000Hz @ 1Hz Intermittent
2400Hz @ 1Hz Intermittent
2900Hz @ 5Hz Intermittent
363/518Hz @ 1Hz Alternating
450/500Hz @ 2Hz Alternating
554/440Hz @ 1Hz Alternating
554/440Hz @ 0.625Hz Alternating
561/760Hz @0.83Hz (50
cycles/minute) Alternating
800/1000Hz @ 0.875Hz Alternating
2400/2900Hz @ 2Hz Alternating
500/1200Hz @ 0.3Hz Sweeping
560/1055Hz @ 0.18Hz Sweeping
560/1055Hz @ 3.3Hz Sweeping
660/1200Hz @ 1Hz Sweeping
800/1000Hz @ 1Hz Sweeping
800/1000Hz @ 7Hz Sweeping
800/1000Hz @ 50Hz Sweeping
2400/2900Hz @ 7Hz Sweeping
2400/2900Hz @ 1Hz Sweeping
2400/2900Hz @ 50Hz Sweeping
2500/3000Hz @ 2Hz Sweeping
2500/3000Hz @ 7.7Hz Sweeping
800Hz Motor Siren
1200Hz Motor Siren
2400Hz Motor Siren
Stage 1
Set DIP
SW 1
Tone No.
Tone Description Tone Visual
Stage 1 & 2
DIP SW 1/2
Settings
1 2 3 4 5 6
Stage 3
Set DIP
SW 1
(S3)
Stage 4
Set DIP
SW 1
(S2 + S3)
0 0 0 0 0 0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
46
47
48
49
50
52
53
54
55
56
57
58
59
60
61
62
63
42
1 0 0 0 0 0
0 1 0 0 0 0
1 1 0 0 0 0
0 0 1 0 0 0
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
0 0 0 1 0 0
1 0 0 1 0 0
0 1 0 1 0 0
1 1 0 1 0 0
0 0 1 1 0 0
1 0 1 1 0 0
0 1 1 1 0 0
1 1 1 1 0 0
0 0 0 0 1 0
1 0 0 0 1 0
0 1 0 0 1 0
1 1 0 0 1 0
0 0 1 0 1 0
1 0 1 0 1 0
0 1 1 0 1 0
1 1 1 0 1 0
1 1 0 1 1 0
0 0 1 1 1 0
0 1 1 1 1 0
0 0 0 0 0 1
0 1 0 0 0 1
1 1 0 0 0 1
0 0 1 0 0 1
1 0 1 0 0 1
0 1 1 0 0 1
1 1 1 0 0 1
0 0 0 1 0 1
0 1 0 1 0 1
1 0 1 1 0 1
0 1 1 1 0 1
1 1 1 1 0 1
0 0 0 0 1 1
1 0 0 0 1 1
0 1 0 0 1 1
1 1 0 0 1 1
0 0 1 0 1 1
1 0 1 0 1 1
0 1 1 0 1 1
1 1 1 0 1 1
0 0 0 1 1 1
1 0 0 1 1 1
0 1 0 1 1 1
1 1 0 1 1 1
0 0 1 1 1 1
1 0 1 1 1 1
0 1 1 1 1 1
0 0 0 1 1 0
1 0 0 1 1 0
0 1 0 1 1 0
1 1 1 1 1 0
1 0 0 0 0 1
1 0 0 1 0 1
1 0 1 1 1 0
1000Hz
1200Hz
500Hz 1s
1000Hz 1s
1s
1600Hz
1400Hz 1s
0.5s
544Hz 0.1s
0.4s
440Hz
0.5s
1500Hz
500Hz 0.5s 0.5s 0.5s 0.5s 1s
2s 1s
3s 0.5s
1500Hz
500Hz
1200Hz
500Hz
1000Hz
1s
1s
1s
1s
1s
1s
1s
1s
1s
1s
1s
1s
1s
1s
7s
7s
420Hz 0.5s
0.5s
0.5s
0.5s
0.5s
1s
1000Hz 0.5s
0.5s
0.5s
0.5s
0.5s
1s
1200Hz
500Hz 0.85 0.5s 0.85 0.5s 0.85
2000Hz
1000Hz
1s
f(Hz)
a(s)
b(s)
(f=440, a=0.6, b=0.6)
(f=470, a=0.55, b=0.55)
(f=470, a=0.1, b=0.1)
(f=470, a=0.43, b=0.44)
(f=655, a=0.57, b=0.57)
(f=660, a=1.8, b=1.8)
(f=660, a=0.15, b=0.15)
(f=745, a=0.5, b=0.5)
(f=800, a=0.25, b=1)
(f=800, a=0.25, b=0.25)
(f=1000, a=0.5, b=0.5)
(f=2400, a=0.5, b=0.5)
(f=2900, a=0.1, b=0.1)
f1(Hz)
a(s)
f(Hz)
f1(Hz)
a(s) a(s)
f(Hz)
(f=363, f1=518, a=0.1)
(f=450, f1=500, a=0.25)
(f=440, f1=554, a=0.5)
(f=440, f1=554, a=0.8)
(f=561, f1=760, a=0.6)
0 0 1 1 0 1
1 1 0 1 0 1
43
44
45
780/600Hz @ 0.96Hz Alternating
800/1000Hz @ 2Hz Alternating
970/800Hz @ 2Hz Alternating
64 Simulated Bell 1 1 1 1 1 1
f1(Hz)
a(s) a(s)
f(Hz)
(f=800, f1=1000, a=0.57)
(f=2400, f1=2900, a=0.25)
f1(Hz)
a(s) a(s)
f(Hz)
(f=800, f1=1000, a=0.25)
f1(Hz) a(s) a(s)
f(Hz)
(f=600, f1=780, a=0.52)
f1(Hz) a(s) a(s)
f(Hz)
(f=800, f1=970, a=0.25)
(f=500, f1=1200, a=3.34)
(f=560, f1=1055, a=5.47)
(f=560, f1=1055, a=0.3)
f1(Hz)
a(s)
f(Hz)
51 600/1250Hz @ 0.125Hz Sweeping (f=600, f1=1250, a=8)
f(Hz)
a(s)
(f=800, a=1.6)
(f=1200, a=2)
(f=2400, a=1.7)
1450Hz 0.25s
0.69ms
(f=660, f1=1200, a=1)
(f=800, f1=1000, a=1)
(f=800, f1=1000, a=0.14)
(f=800, f1=1000, a=0.02)
(f=2400, f1=2900, a=0.14)
(f=2400, f1=2900, a=1)
(f=2400, f1=2900, a=0.02)
(f=2500, f1=3000, a=0.5)
(f=2500, f1=3000, a=0.13)
(f=300)
(f=440)
(f=470)
(f=500)
(f=554)
(f=660)
(f=800)
(f=1200)
(f=2000)
(f=2400)
f(Hz)
0.5s
2
3
2
24
19
44
44
24
34
34
1
1
1
3
44
44
44
24
24
24
24
24
24
24
24
24
24
8
8
24
8
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
8
8
24
8
21
24
24
24
24
24
24
24
24
24
3
20
44
44
44
1
1
1
1
35
1
1
8
8
8
35
8
8
8
8
8
8
8
8
8
19
19
19
19
19
19
19
19
19
19
19
19
19
19
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
1
1
8
8
8
35
35
35
35
35
f1(Hz)
a(s)
f(Hz)
This manual suits for next models
7
