CombiSteel G6IN100E Instructions for use

INDUCTION COOKER
(ELECTRICAL)
INSTRUCTION AND
MAINTENANCE MANUAL
“Professionally with Professionals”

CATALOGUE
Catalogue ............................................................
1. Introduction and working principle of induction
cooker ..................................................................
1
2.
Operating instructions......................................
1
3.
Matters needing attention ...............................
5
4.
Common failure phenomena and troubleshooting
methods ...............................................................
7
— 1 —

1.Introductionand working principle of kitchen in
kitcheninductioncooker
---------------------------------
The induction cooker is a new type of stove in the kitchen ware
market. It breaks the traditional open flame cooking method. The
working principle of electromagnetic heating is to pass a high-
frequency current through the coil disk to generate a magnetic field
on both sides of the coil disk. When the iron pot is within the magnetic
field, the pot cuts the alternating magnetic field lines produce
alternating currents in the pot (ie. eddy current). The eddy current
causes the iron molecules of the pot to move randomly at high speed.
The molecules collide with each other and rub against each other to
generate heat energy to make the appliance itself heat up at high
speed for heating and cooking food. So as to achieve the purpose of
cooking.
2. Operating Instructions
--------------------------------------------
Knob
Display
ON/OFF
Time
Power
Temperature
— 2 —

1. Heatingfunction:
Power on: Turn on the power, the indicator lights are all on, and the
digital tube displays the corresponding model, such as "P350" for
3500W flat-hearth furnace series, "A350" for 3500W concave furnace
series, " P250" for 2500W flat-head furnace series, "A250" "Means
2500W concave furnace series, "P500" means 5000W flat-top furnace
series, and "A500" means 5000W concave furnace series. "P-15"
means 15KW flat-top stove series, "A-20" means 20KW concave type
frying stove series. After about 2S, the indicator light is off, the power
light flashes, and the digital display " ----" indicates the standby state.
Power on: Press the power "switch" button once (Note: When all touch
buttons are operated, press the finger at the center of the corresponding
button pattern. Each time you press it, you should stay for a while, and
then let go. Because the button has the function of preventing
misoperation, the button The action should not be too fast, otherwise the
key will be invalid), the digital display "on", press the "firepower" key
again, the corresponding power will be displayed, the default maximum
gear; or press the "fixed temperature" key once to display the
corresponding set temperature, The default is 200°C. All the indicator
lights are on, and it can be heated after putting the pot. If you press the "
Firepower" key during the constant temperature process, it can also be
set to theheating function.
Firepower/temperature adjustment: Adjust the appropriate power
(firepower) and temperature through the knob. Turn clockwise to increase
firepower (temperature), and turn counterclockwise to decrease firepower
(temperature). The gears aredividedinto9 levels.
G7WIN100E – 700 serie ½ module cupboard
G7IN100E-S – 700 serie ½ module counter top
G7IN200E-S – 700 serie 1 module counter top
G7WIN100E-S – 700 serie ½ module counter top
G9WIN100E – 900 serie ½ module Wok Cooker
G9IN100E-S – 900 serie ½ module counter top
G9IN200E-S – 900 serie 1 module counter top
G9WIN100E-S – 900 serie ½ module counter top
G7IN100E – 700 serie ½ module cupboard
G9IN200E – 900 serie 1 module cupboard
G7IN200E-W – 700 serie 1 module without cupboard
G9WIN100E-W – 900 serie ½ module Wok Cooker without cupboard
G7IN200E – 700 serie 1 module cupboard
G7WIN100E-W – 700 serie ½ module without cupboard
G6IN100E – 600 serie ½ module counter top
G9IN100E-W – 900 serie ½ module without cupboard
G6IN200E – 600 serie ½ module counter top
G9IN100E – 900 serie ½ module cupboard
G7IN100E-W – 700 serie ½ module without cupboard
G9IN200E-W – 900 serie 1 module without cupboard
— 3 —

2. Constant temperature function: Turn on, press the "fixed
temperature "button, or press the "fixed temperature" button once
when the induction cooker is working in the heating function, the
display will show the gear position, such as the digital display ‘’ 200C’’
means 200°C, enter the temperature function, the appropriate
temperature can be adjusted through the knob.
Clockwise rotation temperature increases, counterclockwise
rotation temperature decreases, and the gears are divided into
9gears.
3. Shutdown:
During the operation of the induction cooker, press the power
switch button once, the power light flashes, the digital tube
displays " --- ", and the other indicator lights are off, indicating
that it enters the standby state.
4. Timingsetting:
The timing function can be set for the heating mode or constant
temperature mode of the induction cooker. Press the time
button once, the number flashes, enter the timing shutdown
setting. When the time key is pressed for the first time
The nixie tube displays "00:00" flashing, indicating that the
timing time is 0 minutes (that is, there is no timing).
The required timing time can be adjusted through the knob. The
clockwise rotation time adds 10 minutes, and the
counterclockwise rotation time subtracts 1 minute. The
maximum timing time can be set to 23:59. If you do not adjust
the knob, it will automatically confirm after about 5 seconds and
enter the countdown. If you press the "timing" key again within 5
seconds, the timing setting will be cancelled; in addition, the
timing will not work when it displays 00:00.
After the time setting is completed, the timing starts. After the
timer is started, the display will switch back and forth between
timeandfirepower(temperature).
When the time is up, it will automatically shut down and enter
the standby state, the power light flashes, and the digital tube
displays " --- ".
-4-

3. Matters needing attention
----------------------------------------------
1. Thestove must beplaced stably;
2. Leave a space of about 20cm behind the stove to facilitate
thefanto dissipateheat.
3. This electric stove is powered by 220V single-phase or
380V three-phase, andmust begroundedreliably.
4. Dry burning in empty pot is strictly prohibited;
5. Before the power is disconnected, the induction cooker
must beturned off and in astandby state;
6. Pleasedisconnect the power if not used for a long time;
7. When the stove has glass-ceramics, please avoid being hit
by hard objects and use matching pots;
8. If the glass-ceramic is damaged, please stop using
it immediately anddisconnect the power supply;
9. Pleasepay attention towaterproofing when cleaning the
stove(cannot becleaned with jet water);
10. This induction cooker cannot be used to cook porridge or
soymilk, otherwiseit will easily cause dry burning and danger;
11. The concave cookware used in this stove is matched with
the manufacturer. If the user needs to replace it, please choose
the same size and material (iron) as the manufacturer, or contact
the manufacturer to purchase. Otherwise, the firepower may not
meet the requirements, and it may even break the glass and
cause danger. Table-top flat pots should be made of iron pots
with a bottom diameter greater than 26cm. Pots with a diameter
less than 33cm should not exceed 10kg in total weight. Pots with
a diameter greater than 33cm should not exceed 20kg in total
weight to avoid damage. Glass is dangerous.
12. During the use of the stove, metal objects such as
kitchen utensils, knives and forks arenot allowed
Put it in the cooking area on the cooktop, otherwise, when it is
near the wok (within the magnetic field), it will automatically heat
up andcausedanger;
-5-

13. Do not place aluminum foil or plastic containers on a hot
surface, and do not stack objects on thesurface of the stove;
14. During operation, if the operator wears metal (iron) jewelry
(rings, bracelets, watches, etc.) on his hands, the jewelry may
automatically heat up when his hands are near the wok (within
the magnetic field). At this time, stop the operation immediately
andremovethe accessories.
15. Users with pacemakers should consult with the
manufacturerbeforeoperatingthestove;
16. When thestove fails, it can only be repaired by
personneltrained or recommendedbythemanufacturer.
17. "
"Highvoltage danger sign: It means there is
High voltagein themachine, please becarefulwhen
repairing operation,non-professionalsdonotdisassemble.
18. "
"Cautionmagnetic fieldsign: indicates that the
induction cooker generates a magnetic field when it is
working. Pleasepayattentionwhenoperating.
-6-

4. Common failure phenomena and troubleshooting method
Error code
Failure phenomenon Method of exclusion
"E01" flashes
IGBT sensor open circuit
1. Check whether the IGBT sensor is open
2. Check whether the IGBT sensor terminal is loose
"E02" flashes
IGBT sensor short circuit
1. Check whether the IGBT sensor is damaged
2. Check whether the IGBT connection is short-circuited or welwed
"E03" flashes
Wire reel sensor open circuit
1. Check whether the wire reel sensor is damaged
2. Check whether the sensor cable is disconnected and whether there is
poor contact.
"E04" flashes
The wire reel temperature is high or
the wire reel sensor is short-circuited
1. Check whether the sensor is damaged
2. Check whether the sensor cable is disconnected
3. Check whether the sensor interface is loose
4. Check whether the coil disk cooling fan rotates or the speed is to slow
5. Check whether the air infet or exhaust vent is blocked
"E05" flashes
Furnace sensor open circuit
Check whether the sensor cable is disconnected and whether there is
poor contact.
"E06" flashes
Furnace sensor short circuit
1. Check whether the sensor is damaged
2. Check whether the sensor line is short-circuited
"E07" flashes
Grid voltage is too low
1. For 1.220V models, check whether the grid voltage is lower than 150V.
and for 380V models, check whether the grid voltage is lower than 350V.
2. Check whether the core power transformer is damaged
"E08" flashes
Grid voltage is too high
For 1.220V models, check whether the grid voltage is higher than 260V,
and for 380V models, check whether the grid voltage is higher than 450V.
"F" flashes
IGBT temperature is too high
1. Check whether the movement fan rotates or the spees is too slow
2. Check whether the air infet or exhaust vert is blocked
"E00" flashes
No pot or inappropriate pot
1. Check whether the wire reel and the wire reel terminal are loose.
2. Check whether the pot is severely deformed.
3. Check whether the pot material used is suiteble, whether the bottom
of the pot is seriously deformed, and whether the pot is placed in the
correct position.
-7-