Comelit 100 SERIES User manual

CAMERAS WI-FI IP 100 SERIES
Please read this manual thoroughly before use and keep it for future reference

Contents
1. Login Interface........................................................................................................................................................1
2. Live view................................................................................................................................................................. 2
2.1 Full-screen Preview.....................................................................................................................................2
2.2 Electronic Zoom-in.......................................................................................................................................2
2.3 PTZ Control.................................................................................................................................................3
3. Playback.................................................................................................................................................................4
4. Setup......................................................................................................................................................................5
4.1 Device Info ..................................................................................................................................................5
4.2 QR Code ..................................................................................................................................................... 6
4.3 ePTZ Setting................................................................................................................................................7
4.4 Display Settings...........................................................................................................................................7
4.5 Encoding ..................................................................................................................................................... 8
4.6 Video Parameters........................................................................................................................................9
4.7 Motion Detection........................................................................................................................................10
4.8 Video Tampering.........................................................................................................................................11
4.9 Privacy Mask.............................................................................................................................................12
4.10 Network Settings......................................................................................................................................12
4.11 Wifi Config............................................................................................................................................... 13
4.12 Platform Management..............................................................................................................................15
4.13 Multicast Config.......................................................................................................................................15
4.14 DDNS Setting.......................................................................................................................................... 15
4.15 NTP Settings ...........................................................................................................................................16
4.16 Email Settings..........................................................................................................................................17
4.17 FTP Settings............................................................................................................................................ 18
4.18 Alarm Input ..............................................................................................................................................18
4.19 Alarm Out ................................................................................................................................................ 19
4.20 Exception Settings................................................................................................................................... 20
4.21 User Info.................................................................................................................................................. 21
4.22 System Update........................................................................................................................................22
4.23 Auto Reboot............................................................................................................................................. 22
4.24 Storage Management .............................................................................................................................. 23
4.25 Restore.................................................................................................................................................... 23
4.26 Local Setting............................................................................................................................................24
5. File Management..................................................................................................................................................25
5.1 Search....................................................................................................................................................... 25
5.2 Playback Capture...................................................................................................................................... 25
5.3 Backup......................................................................................................................................................25
5.4 Linkage Capture........................................................................................................................................25
5.5 Preview Capture........................................................................................................................................ 26
5.6 File Capture............................................................................................................................................... 26
5.7 Preview Videos.......................................................................................................................................... 26
5.8 Backup Video Play.....................................................................................................................................26
6. Log.......................................................................................................................................................................26
7. Exit....................................................................................................................................................................... 27

Statement
The instruction is for guidance only. Detailed information is in accordance with the product.
The instruction may include some technical inaccuracies or typographical error thought it is prepared with our every
effort.
The product or procedures described in the instruction may be changed or updated at any time without advance
notice.
Screenshots used in the instruction are from the other machine and are only for indications and explanations.
For any doubts or to request documents about latest procedures and complementary notes, please consult with the
after-sales service department.
Precautions
The followings describe information about correct usage and risk prevention as well property loss prevention to be
strictly followed.
Please use web cameras in an environment within allowable temperature (-10°C to +50°C) and humidity.
Check if the power supply works normally before operation.
Do not furiously strike on the product and be careful not to fall it over.
Do not install the product in a dusty or moist place, or a place with strong electromagnetic radiation.
Do not place a container or others with liquid on the product or allow liquid flowing into inside the product.
When the product is left unused, place install the preventive dust cover for the image sensor.
Do not disassemble the product without authorization.

1
1. Login Interface
Input the IP address of the front-end device into the IE browser (default IP address is 192.168.1.188) to access
the Login interface, as shown in the following figure:
After entering into the login interface, it will prompt to install the Activex control, as shown in the following
figure:
User Name: admin (default setting)
Password: blank (default setting)
Model: IEActiveX or NonActiveX. If you use IE browser, then please select IEActiveX to login. While you use
other browsers, then select Non ActiveX to login. (Note: Select NonActiveX without installingActiveX control)
Select Language: select the desired language
Click Submit to login.

2
2. Live view
After login, it will enter into the live preview, as shown in the following figure.
Note:The device need to insert micro-SD card for full function display interface, otherwise, it's for simple type
interface.
2.1 Full-screen Preview
Click the full-screen icon in the lower right corner to preview full screen. Or you can click right mouse
button to enter and exit the full screen display in the preview interface.
2.2 Electronic Zoom-in
It can zoom in the preview image by scrolling the mouse wheel, as shown in the following figure:

3
2.3 PTZ Control
Zoom In/ Out: To adjust degree of zoom in/ out
Focus: To adjust size of focus
Iris: To adjust size of aperture
Speed: Use the slider to regulate the PTZ speed
Bright: To adjust the brightness of the screen
Contrast: To adjust the contrast of the screen
The arrow is used to restore default settings.
Set APreset Point:Set a preset point by using directional keys on the PTZ control to rotate the camera to the desired
location, next select a preset number from the Preset Point drop-down list, and then press button.
Call A Preset Point: Call a preset point by selecting a preset number to be called from the Preset Point drop-down
list and press button.
Voice Intercom: Click it to enable or disable voice intercom
Capture: Capture for preview. Click the capture icon, it will pop up its storage path automatically.
Full Screen: Display the current preview in full screen
Record: Enable or disable preview interface record
Event Type: Enable or disable disarming/ clear alarm
Note: X indicates the function is off or disabled
VOICE INTERCOM
Capture
Full Screen
Record
Event Type

4
3. Playback
Click Playback enter into playback interface, click the icon , next select the date time of the calling
video in need, then click the icon , the record video will search automatically, as shown in the following
figure:
Start: Start the current playback
Stop: Stop the current playback
Slow：Slow down the playback speed(1/2, 1/4, 1/8, 1/16 times optional)
Fast：Speed up the playback speed(2, 4, 8, 16 times optional)
Snapshot: Can be snapshot in playback channel
Backup：Can be backup video in playback channel
Frame Play：Single frame to play
Full Screen: Playback video will display with full screen
Voice: Adjust the volume of playback audio
Double-click the slider location, it will start to paly the video, or you can click the Start button to playback video.
Note: The device need to support and insert micro-SD card to enable this function.

5
4. Setup
Note:the device need to insert micro-SD card for full function display interface, otherwise, it's for simple type
interface
4.1 Device Info
IP Camera Device Info interface as shown in the following figure:
Device Name: Edit the camera name
Device Type: Display the device type
Serial No. : Display the product serial No.
Master Version: Display the software version date
Hardware Version: Display the hardware version number
Audio Source: Select the audio input mode, LineIn or MicIn selectable
Input Volume: Set the size of the input volume，the range of volume:0-100, default is 50

6
Output Volume: Set the size of the output volume，the range of volume:0-100, default is 50
Format: Switch to select the PAL and NTSC image scanning system
Device Time: Set and display the device current time
After complete all parameters setting, click Save and then it will take effect immediately.
4.2 QR Code
Scan the QR code to login directly via mobile phone client, the IP camera QR code interface as shown in the
following figure:
Note: after enable the corresponding protocol in the platform management interface, then the QR code icon will
display. QR code supported: Comelit View 100. During the platform management interface, Comelit View 100_ID
protocol should be matched with Comelit View 100 client.

7
4.3 ePTZ Setting
IP Camera ePTZ Set interface as shown in the following figure:
Protocol: Support PelcoD and PelcoP protocol
Address: Support 0-255 address code adjustable
Baud Rate: Support diverse baud rate selectable
After complete all parameters setting, click Save and then it will take effect immediately.
4.4 Display Settings
IP Camera Display Settings interface as shown in the following figure.

8
Name: Modify the appointed channel name
Main Stream OSD: Modify the appointed channel font of main stream OSD
Sub Stream OSD: Modify the appointed channel font of sub stream OSD
Multi OSD:Add multi user-defined OSD, it can be selected Show or not
Time Format: Select different time display mode for the appointed channel
Date Format: Select different date display mode for the appointed channel
Bright: Adjust the brightness for the appointed channel
Contrast: Adjust the contrast for the appointed channel
Saturation: Adjust the saturation for the appointed channel
Hue: Adjust the hue for the appointed channel
CH(Title Location): Set the channel title location for the appointed channel
OSD(Date Adjustment): Set the channel date location for the appointed channel
Multi OSD(position adjustment):Set the position of multi OSD
Cyclotron Arrow: Restore the default parameters(Only for Bright, Contrast, Saturation and Hue)
After complete all parameters setting, click Save and then it will take effect immediately.
4.5 Encoding
IP Camera Encoding setting interface as shown in the following figure:
Compress Type: Primary Stream(Normal)/ Sub Stream selectable
Stream: Include complex stream/ video stream two types
Resolution: The camera supports several relolution, will display here
Frame Rate: Select different frame rate in the drop-down list, default is Full Frame
Video Encode: H.264/ MJPEG two kinds of video encode format
H264 Profile: There are MainProfile/ Baseline/ HighProfile three types optional
I frame Interval: Set the I frame interval time
Bitrate Type: Constant/ Variable selectable
Bitrate: Set different bitrate for different channels
After complete all parameters setting, click Save and then it will take effect immediately.

9
4.6 Video Parameters
IP Camera Video Parameters setting interface as shown in the following figure:
Day&Night Mode: Outside Trigger/ Auto/ Color/ Black White four kinds of mode selectable. Non infrared IP
cameras default mode is Auto, and infrared IP cameras default mode is Outside Trigger. According to the IP camera
type and actual scene, user can select the Day&Night mode optional
Switching Time: Day&Night switch delay time, 0-30s selectable, and default is 3s
Day-Night: 0-255 selectable, users can adjust it according to the need, default is 45
Night-Day: 0-255 selectable, users can adjust it according to the need, default is 119
Color Mode: Normal/ Bright/ Nature three options, default is Normal
Mirror: Close/ Horizonal Mirror/ Vertical Mirror/ 180° Rotation/90° Rotation/270° Rotation six options, default is
Close
WDR: Close/ Low/ Mid/ High four options, default is Close
3DNR: Close/ Low/ Mid/ Mid-High/ High five levels, default is Close
Sharpness: 0-255 selectable, default is 128
Exposure Control Mode: Auto/ Manual selectable, default is Auto
AGC: Low/ Mid-Low/ Mid/ Mid-High/ High selectable, default is Mid-High. The higher Auto Gain value, the better
sensitivity within low illumination, while the noise will be more obvious
Shutter: Manual exposure can be set up, the range of shutter value: 1/30(25)-1/10000
Gamma: CURVE_1_6, CURVE_1_8, CURVE_2_0, CURVE_2_2 totally four modes, default is CURVE_2_0
Anti-Fliker: Close, 50hz, 60hz three types, the default is Close
Aperture: According to the IPC lens type, it can select Manual or Auto for the aperture adjustment, default is
Manual
After complete all parameters setting, click Save, the settings will take effect immediately.

10
4.7 Motion Detection
IP Camera Motion Detection setting interface as shown in the following figure:
Enable: Select whether to enable the Motion Detection function.
Arm Schedule: Set the alarm schedule from Monday to Sunday
Mask Set: Press and darg the left mouse button in the Mask Set preview interface, then draw the small check
optional to set the detective areas
Clear: Click Clear to clear the current detective areas
Sensitivity: The higher sensitivity, the more obvious motion detective effect
Email: Click Email. Once alarm triggers that it will send Email to appointed mailbox
Snap: Click Snap. Once alarm triggers that it will linkage camera to snapshot picture and store it in the micro-SD
card
Record: Click Record.Once alarm triggers that it will linkage camera to record video and restore it in the micro-SD
card.
Alarm Output: There is a active warner connected to the alarm output port. Once alarm triggers that it will linkage
embedded relay switch to make alarm output
Snap Interval: Set the alarm interval time
Snap Count: Set the snapshot image count for every time
After complete all parameters setting, click Save, the settings will take effect immediately.

11
4.8 Video Tampering
IP Camera Video Tampering setting interface as shown in the following figure:
Enable: Select whether to enable the Video Tampering function.
Arm Schedule: Set the alarm schedule from Monday to Sunday
Mask Set: Press and darg the left mouse button in the Mask Set preview interface, then draw the small check
optional to set the detective areas
Clear: Click Clear to clear the current detective areas
Sensitivity: The higher sensitivity, the more obvious motion detective effect
Email: Click Email. Once alarm triggers that it will send Email to appointed mailbox
Snap: Click Snap. Once alarm triggers that it will linkage camera to snapshot picture and store it in the micro-SD
card
Record: Click Record. Once alarm triggers that it will linkage camera to record video and restore it in the micro-SD
card.
Alarm Output: There is a active warner connected to the alarm output port. Once alarm triggers that it will linkage
embedded relay switch to make alarm output
Snap Interval: Set the alarm interval time
Snap Count: Set the snapshot image count for every time
After complete all parameters setting, click Save, the settings will take effect immediately.

12
4.9 Privacy Mask
IP Camera Privacy Mask setting interface as shown in the following figure:
Enable: Enable or disable the Privacy Mask function
Area Settings: Press and drag the left mouse button in the Area Settings preview interface, then draw the check
optional to set the mask area
Clear: Click Clear to delete the current mask area
After complete all parameters setting, click Save and then the settings will take effect immediately.
4.10 Network Settings
IP Camera Network Settings interface as shown in the following figure:
IPV4: IP protocol version No. is 4
IPV6: IP protocol version No. is 6, the feature is not selectable at present

13
Static IP: The device IP address is permanent
DHCP: Enable DHCP, then IP camera will get the IP address from router automatically
IP Address: Input the corresponding numbers to change the IP address
Subnet Mask: Input the corresponding IP subnet mask
Gateway: Input the corresponding gateway address
DNS 1: DNS server IP address
DNS2: DNS server second IP address
HTTP Port: Input the corresponding port ( Default is 80)
HTTPS Port: Input the corresponding port ( Default is 443)
RTSP Port: Use domain name to access and login device need mapping RTSP, default port is 554
RTMP Port: Use domain name to access and login device need mapping RTMP, default port is 1935
Enable UPnp: Enable UPNP, then device port and HTTP port will be mapped to the router automatically
Device Port: Input the corresponding device port(Default is 5050)
After complete all parameters setting, click Save, then the settings will take effect immediately.
4.11 Wifi Config
IP Camera Wifi Config interface as shown in the following figure:
Work Mode: Show the current work mode, there are two work modes optional.AP mode supports matching WIFI
via cell phone client and STAmode supports matching WIFI via web client of PC.
Current Status:
Work Mode: Show the current work mode for IPC
SSID: Show the serial number for IPC
AUTH: Show the Wifi authentication method for the current router connected
IP: Show the current wireless IP address for IPC
Wifi Config: Can set specific configuration for Wifi connection in the AP List and Connect Config, the steps to

14
configure as follow:
1. Search Wifi device: Copy the SSID serial number in the Current Status to the blank of SSID part in the
Connect Config, click Save, will automatically switch to STA mode, click Refresh, then AP List will display all the
Wifi device names within the acceptable range, as shown in the following figure:
2. Connect Wifi: click the current Wifi device (that is wireless router) connected via network cable at the IPC, select
the AUTHmethod for router in the Connect Config, then input password and select IP mode (Static: fixed IP settings,
DHCP: assign IP address automatically by router).After finishing above settings, click Save . Click Connect in the AP
List and the wireless IP address will be generated and displayed in the IP position of Current Status, as shown in the
following figure:

15
4.12 Platform Management
IP camera Platform Management interface as shown in the following figure:
User can open, close, edit and delete the protocol in the Management Platform interface.
4.13 Multicast Config
IP Camera Multicast Config interface as shown in the following figure:
Default disabling for multicast config. After click"Enable Multicast", users can set IP address,Port and TTL of
primary stream video,primary stream audio, sub stream video, sub stream audio.
4.14 DDNS Setting
DDNS is implemented through a dynamic domain resolution server. It requires a PC running in the Server

16
with fixed IP address on the Internet. IP Camera network setting interface as below figure:
Enable DDNS: Enable or Disable DDNS function
Server Type: Select DDNS server type
Server Name: Input server name
Port: Input port.default port is 80
User Name: Input user name
Password: Input password (max 10 char.)
Confirm pwd: Input the password again to confirm it
Domain: Input the hostname
After complete parameters setting, click Save and then the settings will take effect immediately.
4.15 NTP Settings
IP Camera NTP Settings interface as shown in the following figure:

17
Enable NTP: Enable or disable NTP function
Server Address: Input NTP server IP address
NTP Port: Default port is 123
Adjust Time Interval: Input the interval time
Select Time Zone: Different area time format selectable
GMT: Adjust the time to make it more exact
After complete all parameters setting, click Save, then the settings will take effect immediately.
4.16 Email Settings
IP Camera Email Settings interface as shown in the following figure:
(sent)Email Address: Input the address of the outbox
Password: Input the the password of the outbox