Comelit AHPTZ110A User manual

1
AHD PTZ CAMERA
ART. AHPTZ110A – AHPTZ120A
Please read this manual thoroughly before use and keep it for future reference

2
Contents
Menu Index ....................................................................................................................................................................... 7
Menu Index ............................................................................................................................................................................ 8
1 MENU SETTINGS .................................................................................................................................................................... 9
1.1 SYSTEM INFORMATION ............................................................................................................................................... 9
1.2 MOTION SETUP ......................................................................................................................................................... 10
1.2.2 DISPALY SETUP ................................................................................................................................................ 10
1.2.3 PATH SETUP .................................................................................................................................................... 11
1.2. CONTROL SETUP ............................................................................................................................................. 1
1.2.5 ADDR SETTING ............................................................................................................................................... 15
1.2.6 ALARM SETTING ............................................................................................................................................. 15
1.2.7 IR SETTING ...................................................................................................................................................... 16
1.3 CAMERA SETUP ......................................................................................................................................................... 17
1.3.2 WHITE BAL ...................................................................................................................................................... 18
1.3.3 BACK LIGHT .................................................................................................................................................... 18
1.3. WDR ............................................................................................................................................................... 18
1.3.5 FOCUS ............................................................................................................................................................. 18
1.3.6 ESPOSURE ....................................................................................................................................................... 19
1.3.7 SPECIAL ........................................................................................................................................................... 19
1.3.8 RESET .............................................................................................................................................................. 20
1. USER ADMIN ............................................................................................................................................................. 20
1. .1 PRESET LOCK .................................................................................................................................................. 21
1. .2 ENABLE PASSWORD ........................................................................................................................................ 21
1. .3 EDIT PASSWORD ............................................................................................................................................. 22
1.5 SYSTEM SETUP .......................................................................................................................................................... 22
1.5.2 REBOOT SYSTEM ............................................................................................................................................ 23
1.5.3 FACTORY DEFAULT .......................................................................................................................................... 23

3
Cautions
Non-professional do not disassemble the PTZ camera. Please read this manual carefully before operating. (This
specification is subject to change without prior notice.)
Cut the power supply off before operating the device to avoid damage caused by mis-operation.
Interior of the PTZ camera are precision optical and electrical instruments.Heavy pressure, shock and other
incorrect operations should be prevented.Otherwise, may cause damage to product.
Please do not use the product under circumstances where the limits exceed the maximum specified temperature,
humidity or power supply specifications.
Contents in this manual may be different from the edition that you are using.Should any unsolved problem occur
given that the product is used according to this manual, please contact our technical support department or your
product suppliers.
This manual content will be updated unscheduled, our company reserves the right to do manual contents update
without further notice.
The default factory address code is No. 1. The automatic recognition communication protocols are PELCO-D and
PELCO-P. The automatic recognition baud rate are 2400 bps, 4800 bps, 9600 BPS and 19200 bps.

System Requirements
1 Control keyboard or other control device (with RS485 port)
2 Monitor or other display device (with VIDEO IN port)
3 100÷240 VAC input, 24 VDC/1.5A output power adapte r
Installation environment
Installation environment requirements
Do not use in humid or high temperature environment, pay attention to keep good ventilation, avoid installation in the
environment of severe vibration, as far as possible away from heating devices.
Recommended using environment
Temperature ： -30 ÷ +60 °C
Humidity ： 0% ÷ 90% RH (not condensing)
Installation Steps
Before installing the smart PTZ camera, we hope you have confirmed that your control keyboard and monitor are working
properly. After confirming that your device system is in good condition, please follow the following steps and keep your hands clean
and dry.
Open the packing box and check the integrity of the goods.
Remove all items needed for installation
Connect relevant cables (power supply, control linear, alarm linear, etc.) according to actual needs
Turn on the power supply
Note ：


Please check carefully when unpacking the box to make sure that the items in it are in accordance with the list.


Please read the user manual carefully before installation.


When installing the camera, be sure to turn off all the power supply.


Check the power supply voltage to prevent device damage caused by voltage mismatch


Connect power supply

5
Wiring instructions: wire functions introduction from
top to bottom
Art. AHPTZ110A
① Video input
② Reset
③ Power supply
④ Alarm input
⑤ Alarm output
⑥ RS485
Art. AHPTZ120A
① Video input
② Reset
③ Power supply -
④ Power supply +
⑤ Alarm input
⑥ Alarm Output/RS485

6
Operation method
The PTZ camera can be connected with keyboard device through RS485. The camera can be remotely controlled by moving up
and down, moving left and right, and zooming lens.
General functions
4.1 Up and down, left and right moving functions
Up, down, left and right can be controlled by rocker. The speed of rocker control is changeable. The bigger the angle of
inclination, the faster the speed of movement. The position diagram of rocker handle is shown in Figure 4-1-1.
Figure 4-1-1
4.2 Lens control
Change the camera's field of view (zoom in and zoom out) press [TELE] or [WIDE].
4.3 Basic operation of main menu
（ 1 ） “95+CALL” enters the camera main menu.
（ 2 ） The rocker handle moves up and down to see the menu bar pointed by the cursor; the rocker handle moves right to enter the
sub-menu of the item where the cursor is located or to enter the function of the item where the cursor is located; the rocker handle
moves left (or executes the "Back" menu item) to return to the previous menu.
（ 3 ） If the cursor is in the selection state of the current menu item, moving the rocker up or down can change the current selection,
and moving the rocker left or right can exit the current selection and save the current selection.
（ 4 ） If the menu item where the cursor is located has a subordinate menu, press [OPEN] to enter the subordinate menu.
（ 5 ） Press [EXIT] (or execute the "Exit” menu item) to close the menu.
Tip: The menu structure of the PTZ camera is shown in the menu index.

7
Menu Index
Connected (b)
Connected (a)
PATH SETUP
SWING SETUP
CRUISE SETTING
PATTERN SETUP
CONT-SCAN SETUP
BACK
EXIT
PATTERN SETUP
NUMBER 1
SET PATTERN
CALL PATTERN
CLEAR CURRENT
BACK
EXIT
PRESET SPEED TIME
19 --- - ---
20 --- - ---
BACK
EXIT
DISPLAY SETUP
SYS- INFORMATION OFF
FUNC-DISPLAY OFF
COORDINATE OFF
PRESET SETUP
MASK SETUP
BACK
EXIT
ADDRESS 0
PROTOCOL PELCO-D
BAUD RATE 2400
PT VERSION V1.10
PRESET SPEED TIME
1 --- - ---
2 --- - ---
3 --- - ---
4 --- - ---
5 --- - ---
6 --- - ---
7 --- - ---
8 --- - ---
9 --- - ---
NEXT
SWING SETUP
NUMBER 1
SET SWING
SPEED 9
AREA MAJOR ARC
CALL SWING
CLEAR CURRENT
BACK
EXIT
PRESET SPEED TIME
10 --- - ---
11 --- - ---
12 --- - ---
13 --- - ---
14 --- - ---
15 --- - ---
16 --- - ---
17 --- - ---
18 --- - ---
NEXT
CRUISE SETTING
NUMBER 1
EDIT CRUISE
OPEN CRUISE
CLEAR CURRENT
BACK
EXIT
CONTROL SETUP
POWER UP ACTION
PARK ACTION
PROPORTIONAL OFF
AUTO FLIP ON
HM SPEED 10
BACK
EXIT
POWER UP ACTION
ACTION TYPE NONE
ACTION NUM ---
BACK
EXIT
CONT-SCAN SETUP
NUMBER 1
SPEED 9
SET CONT-SCAN
CALL CONT-SCAN
CLEAR CURRENT
BACK
EXIT
MAIN MENU
SYSTEM INFORMATION
MOTION SETUP
CAMERA SETUP
USER ADMIN
SYSTEM SETUP
EXIT
ADDR SETTING
ADDR HARD 0
ADDR TYPE SOFT
ADDR SOFT 0
BACK
EXIT
PARK ACTION
TIME M 1
ACTION TYPE NONE
ACTION NUM ---
BACK
EXIT
MOTION SETUP
DISPLAY SETUP
PATH SETUP
CONTROL SETUP
ADDR SETTING
ALARM SETTING
IR SETTING
BACK
EXIT
ALARM SETTING
NUMBER 1
ALARM ACT ACTION
INPUT TYPE CLOSE
OUTPTU TYPE CLOSE
DWELL TIME 0
ACTIVATE AUS OFF
CLEAR CURRENT
BACK
EXIT
ALARM ACT SETUP
ACTION TYPE PRES
ACTION NUM 3
BACK
EXIT

8
（
a
）
（
b
）
IR SETTING
IR LED AUTO
NEAR IR LED ---
MID IR LED ---
FAR IR LED ---
BACK
EXIT
FOCUS SETUP
MODE AUTO
ZOOM SPEED HIGH
D-ZOOM
D-ZOOM RATE
BACK
EXIT
USER ADMIN
PRESET LOCK OFF
ENABLE PASSWORD OFF
EDIT PASSWORD
BACK
EXIT
SYSTEM SETUP
CLEAR SETTINGS
REBOOT SYSTEM
FACTORY DEFAULT
BACK
EXIT
MAIN CAMERA MEUN
WHITE BAL AUTO
BACK LIGHT OFF
WDR OFF
FOCUS
ESPOSURE
SPECIAL
RESET
BACK
EXIT
CLEAR SETTINGS
CLEAR ALL MASKS
CLEAR ALL PRESETS
CLEAR ALL SWINGS
CLEAR ALL CRUISES
CLEAR ALL PATTERNS
CLEAR ALL CONT-SCAN
CLEAR ALL ALARMS
NEXT
CLEAR SETTINGS
CLEAR ALL TASKS
BACK
EXIT
IMAGE SETUP
H-REV OFF
V-REV OFF
FREEZE OFF
BACK
EXIT
ESPOSURES SETUP
MODE AUTO
AGC ---
IRIS ---
SHUTTER ---
3DNR OFF
BACK
E
XIT
SPECIAL SETUP
DAY-NIGHT AUTO
DEFOG ---
IMAGE ADJ
DISPLAY
OUTPUT
BACK
EXIT
FIRET STEP
PUT PLD PASSWORD
BACK SSSSSSSS NEXT

9
1 MENU SETTINGS
After the machine is installed and powered on, the PTZ camera will be self-checked, and the screen will display boot
information, as shown in Figure 1-0-0.
Display PTZ camera address
Display protocol recognition method
Display baud rate recognition method
Figure1-0-0
Explanation: When the PTZ camera is set up differently, the specific values of each item will also be different. This prompt will
disappear until the PTZ camera has completed self-examination. Note: Only when the system display function is turned on in the
menu, will display the boot information.
Enter the main menu: Set the 95 preset point first and then calling the 95 preset point. At this time, the screen shows the main
menu, as shown in Figure 1-0-1.
SYSTEM INFORMATION → (Figure1-1-1)
MOTION SETUP → (Figure1-2-1)
CAMERA SETUP → (Figure1-3-1)
USER ADMIN → (Figure1-4-1)
SYSTEM SETUP → (Figure1-5-1)
Figure1-0-1
1.1 SYSTEM INFORMATION
In the menu of Figure 1-0-1, move the rocker up and down so that the cursor points to the system information, and then move the
rocker to the right to display the system information menu, as shown in Figure 1-1-1.
Display PTZ camera address
Display communication protocol
Display communication baud rate
Display PT version
Figure 1-1-1
Description: The arbitrary movement of the rocker to exit sys information display.
ADDRESS 255
COMMUNICATION PROTOCOL PELCO-D
BAUD RATE 9600
MAIN MENU
SYSTEM INFORMATION
MOTION SETUP
CAMERA SETUP
USER ADMIN
SYSTEM SETUP
EXIT
ADDRESS 0
PROTOCOL PELCO-D
BAUD RATE 2400
PT VERSION V1.10

10
1.2 MOTION SETUP
In the menu of Figure 1-0-1, move the rocker up and down to point the cursor at motion setup, and then move the rocker to the
right to enter motion setup menu, as shown in Figure 1-2-1.
DISPLAY SETUP→( Figure 1-2-2)
PATH SETUP →(Figure 1-2-3)
CONTROL SETUP →(Figure 1-2-4)
ADDR SETTING →(Figure 1-2-5)
ALARM SETTING→(Figure 1-2-6)
IR SETTING →(Figure 1-2-7)
Figure 1-2-1
1.2.2 DISPLAY SETUP
In the menu of Figure 1-2-1, move the rocker up and down so that the cursor points to the display setup, and then move the
rocker to the right to enter the display setup menu. As shown in figure 1-2-2.
Figure 1-2-2
① SYS-INFORMATION: on and off optional, default is off. When set to turn on, when the PTZ camera is powered on, the boot
information is displayed.
② FUNC-DISPLAY: on and off optional, default is off. When set to turn on, the PTZ camera displays the type and number of the
current scan when it is running.
③ COORDINATE : on and off optional, default is off. When set to turn on, the screen displays the horizontal and vertical position
angle of the current PTZ, i.e. Coordinates
④ PRESET SETUP: on and off optional, default is off. When set to turn on, the PTZ camera displays the name of the current preset
point when running the preset point.
⑤ MASK SETUP :default is off, calling the menu, go into the menu interface, open the privacy mask block, set the size of the
privacy mask block, click zoom +-, focus +-.
⑥ BACK: returns the interface for setting privacy masks.
MOTION SETUP
DISPLAY SETUP
PATH SETUP
CONTROL SETUP
ADDR SETTING
ALARM SETTING
IR SETTING
BACK
EXIT
DISPLAY SETUP
SYS-INFORMATION OFF
FUNC-DISPLAY OFF
COORDINATE OFF
PRESET SETUP
MASK SETUP
BACK
EXIT

11
⑦ EXIT: close the interface for setting privacy masks.
1.2.3 PATH SETUP
In Figure 1-2-1, move the rocker up and down so that the cursor points to the path setup, and then move the rocker to the right to
enter the path setup menu. As shown in Figure 1-2-3.
SWING SETUP → (Figure 1-2-7)
CRUISE SETTING → (Figure 1-2-8)
PATTERN SETUP → (Figure 1-2-10)
CONT- SCAN SETUP → (Figure 1-2-11)
Figure 1-2-3
① SWING SETUP: in Figure 1-2-3, move the rocker up and down so that the cursor points to swing setup, and then move the
rocker to the right to enter the swing setup menu, as shown in Figure 1-2-7.
Figure1-2-7
I NUMBER:1-8 optional, PTZ camera can set 8 groups linear scan.
II SET SWING ： move the rocker up and down so that the cursor points to set linear scan, and then move the rocker to the right to
set linear scan state. The rocker moves up and down to select the starting position, and then clicks ［ CLOSE ］ to finish the editing
of the starting point. The same method is used to set the end position. Press ［ CLOSE ］ to save the linear scan settings and return
to the linear scan settings menu.
III SPEED: 1-9 optional, default is 9. 1 is the minimum speed, 9 is maximum speed.
IV AREA: small or large radian optional, default is large radian. When the camera is set to a large radian, the horizontal trajectory of
the camera is the maximum radian at the starting point and the ending point, that is, the maximum-scale scanning and monitoring.
V CALL SWING:In the menu of Figure 1-2-7, move the rocker up and down to make the cursor point to calling linear scan, then
move the rocker to the right to run the current linear scan, and move the rocker arbitrarily back to the linear scan settings menu.
VI CLEAR CURRENT:In the menu of Figure 1-2-7, move the rocker up and down so that the cursor points to delete the current, and
then move the rocker to the right to delete the current linear scan.
PATH SETUP
SWING SETUP
CRUISE SETTING
PATTERN SETUP
CONT- SCAN SETUP
BACK
EXIT
SWING SETUP
NUMBER 1
SET SWING
SPEED 9
AREA MAJOR ARC
CALL SWING
CLEAR CURRENT
BACK
E
XIT

12
② CRUISE SETTING: in Figure 1-2-3, move the rocker up and down so that the cursor points to the cruise setting, and then move
the rocker to the right to enter the cruise setting menu, as shown in Figure 1-2-8.
EDIT CRUISE → (Figure 1-2-9)
Figure 1-2-8
I NUMBER. : 1-8 optional. PTZ camera can set 8 groups cruise scan.
II EDIT CRUISE:In Figure 1-2-8, move the rocker up and down so that the cursor points to the edit cruises, then move to the right to
enters the editing cruise interface, as shown in Figure 1-2-9.
Figure 1-2-9
Description: 20 preset points can be selected for each group cruise. Each group of cruises can set the running speed between
preset points, the speed can be selected from 1-10 levels, 1 level is the minimum speed, 10 level is the maximum speed; the
running time interval between preset points can be set, the time interval can be set to 1-255 seconds.
Operation instructions: in the editing cruise interface, move the cursor up and down to select the Preset point number needed.
Move the rocket to the left to exit without to save. When the cursor is at the Preset point selection item, move the rocker to the right
to select the speed between the preset points. Move the rocker up and down to select the required speed level. When the cursor is
at the desired running speed, move the rocker to the right to select the time interval between the preset points. Move the rocker up
and down to select the required time interval. Move the rocket to the right to save the settings and exits the selection status.
III OPEN CRUISE:In Figure 1-2-8, move the rocker up and down. When the cursor points to start cruise, move the rocker to the
right to start the cruise scan, and move the rocker arbitrarily to go back to the cruise scan settings menu.
IV CLEAR CURRENT:In Figure 1-2-8, move the rocker up and down to the cursor points to delete the current. Move the rocker to
the right to delete the current cruise scan.
CRUISE SETTING
NUMBER 1
EDIT CRUISE
OPEN CRUISE
CLEAR CURRENT
BACK
EXIT
Presets Speed Time
1 --- - ---
2 --- - ---
3 --- - ---
4 --- - ---
5 --- - ---
6 --- - ---
7 --- - ---
8 --- - ---
9 --- - ---
Next screen
Presets Speed Time
10 --- - ---
11 --- - ---
12 --- - ---
13 --- - ---
14 --- - ---
15 --- - ---
16 --- - ---
17 --- - ---
18 --- - ---
Next screen
Presets Speed Time
19 --- - ---
20 --- - ---
Back
Exit

13
③ PATTERN SETUP: in Figure 1-2-3, move the rocker up and down to point the cursor at pattern setup, and then move the rocker
to the right to enter the pattern setup menu, as shown in Figure 1-2-10.
Figure 1-2-10
I NUMBER: 1-4 optional. PTZ camera can set 4 groups pattern scan. Patterns scan realizes recording and playback of arbitrary
trajectory, and its recording parameters include horizontal speed, vertical speed and zoom multiples. Each pattern can record 500
commands.
II SET PATTERN: In the menu of Figure 1-2-10, move the rocker up and down so that the cursor points to the set pattern, and
then move the rocker to the right to enter the set pattern state. Move the rocker up and down and left and right to control the camera
to rotate horizontally and vertically, and change the camera magnification according to [WIDE], [TEIE]. The PTZ camera records the
trajectory of the camera and the camera zoom information in real time. Press ［ CLOSE ］ to save the pattern scanning settings and
return to the pattern scanning settings menu.
III CALL PATTERN: In Figure 1-2-10, move the rocker up and down to point the cursor at calling pattern, then move the rocker to
the right to run the pattern scan, and move the rocker arbitrarily back to the pattern scan settings menu.
IV CLEAR CURRENT: In Figure 1-2-10, move the rocker up and down so that the cursor points to delete current pattern, and then
move the rocker to the right to delete the current pattern scan.
④ CONT- SCAN SETUP: in Figure 1-2-3, move the rocker up and down so that the cursor points to the cont-scan setup and then
move the rocker to the right to enter the cont-scan setup menu, as shown in Figure 1-2-11.
Figure 1-2-11
I NUMBER: 1-4 optional. PTZ camera can set 4 groups group scan.
II SPEED: 1-10 optional, default is 9. 1 level is minimum speed, 10 level is maximum speed.
III SET CONT-SCAN :IN Figure 1-2-11, move the rocker up and down so that the cursor points to the editing group, and then
move the rocker to the right to enter the editing group interface
PATTERN SETUP
NUMBER 1
SET PATTERN
CALL PATTERN
CLEAR CURRENT
BACK
EX
IT
CONT-SCAN SETUP
NUMBER 1
SPEED 9
SET CONT-SCAN
CALL CONT-SCAN
CLEAR CURRENT
BACK
EXIT

1
1.2.4 CONTROL SETUP
In Figure 1-2-1, move the rocker up and down to point the cursor at the control setup, and then move the rocker to the right to
enter the control setup menu. As shown in figure 1- 2-14.
Figure 1-2-14
① POWER UP ACTION ： In Figure 1-2-14, move the rocker up and down to make the cursor point to power up action, and move the
rocker to the right to enter the power up action menu. As shown in Figure 1-2-15.
Figure 1-2-15
I ACTION TYPE : this option is to set power on action type. Presets, linear scan, cruise scan, pattern scan, group scan,
continuous scan and interval scan optional, default is no action.
II ACTION NUM. : this item chooses the number of the action type for the above action type. When the selected item is "---", the
current action type has no optional number, that is, the current action number cannot be set.
② PARK ACTION : In Figure 1-2-14, move the rocker up and down to make the cursor point to park action, and move the rocker to
the right to enter the park action menu. As shown in Figure 1-2-16.
Figure 1-2-16
CONTROL SETUP
POWER UP ACTION
PARK ACTION
PROPORTIONAL OFF
AUTO FLIP ON
HM SPEED 10
BACK
EXIT
POWER UP ACTION
ACTION TYPE NONE
ACTION NUM ----
BACK
EXIT
PARK ACTION
TIME M 1
ACTION TYPE NONE
ACTION NUM ----
BACK
EXIT
POWER UP ACTION → (Figure 1-2-15)
PARK ACTION → (Figure 1-2-16)

15
I TIME: set idle action time, the time can be selected: 1-255 mins. The default idle time is one minute.
II ACTION TYPE: this option is to set the type of idle action. Presets, linear scan, cruise scan, pattern scan, group scan,
continuous scan and interval scan optional, default is no action. The PTZ camera executes idle actions without receiving valid
commands during the set idle time.
III ACTION NUM : this item selects the number of the action type for the above action type. When the selected item is "---", the
current action type has no optional number, that is, the current action number cannot be set.
③ PROPORTIONAL: on and off optional, default is on.
④ AUTO FLIP :on or off, default is on. When set to open, the operator pulls the lens to the bottom (vertical) and then holds the
rocker. At this time, the lens automatically rotates 180 degrees horizontally and then flips 90 degrees upward. It can directly see the
scenery on the back, thus realizing the continuous monitoring of 180 degrees longitudinally. ⑤ Horizontal reverse: on or off, default
is off. When set to open, the rocker left and right movement command will carry out direction processing, that is, the original right
movement command will become the left movement command, and the left movement command will become the right movement
command.
⑤ HM SPEED:Manual operation speed: 1-10 level optional, default speed is 10 level. Level 1 is the lowest speed for manual
operation, and level 10 is the highest speed for manual operation.
1.2.5 ADDR SETTING
In Figure 1-2-1, move the rocker up and down so that the cursor points to the PTZ camera addr setting, and then move the
rocker to the right to enter the PTZ camera addr setting menu. As shown in Figure 1-2-5.
Figure 1-2-5
① ADDR HARD: default is 0.
② ADDR TYPE : default is SOFT.
③ ADDR SOFT: 0-255 optional, default is 0.
1.2.6 ALARM SETTING
In Figure 1-2-1, move the rocker up and down so that the cursor points to the alarm setting, and then move the rocker to the right
to enter the alarm setting menu. As shown in Figure 1-2-6.
ADDR SETTING
ADDR HARD 0
ADDR TYPE SOFT
ADDR SOFT 0
BACK
EXIT

16
ALARM ACT ACRTON → (Figure 1-2-19)
Figure1-2-6
① NUMBER: default is on 1
② ALARM ACT ACTION: in Figure 1-2-6 move the rocker up and down to make the cursor point to the alarm act action, and then
move the rocker to the right to enter the alarm act action menu. As shown in Figure 1 - 2-19
Figure 1-2-19
I ACTION TYPE : this option is to set the type of alarm linkage action. Preset point, linear scan, cruise scan, pattern scan, group
scan, continuous scan and interval scan optional. Default type is no action.
II ACTION NUM : this item chooses the number of the action type for the above action type. When the selected item is "---", the
current action type has no optional number, that is, the current action number cannot be set.
③ INPUT TYPE: normal open or normal close, default is normal close.
④ OUTPUT TYPE: normal open or normal close, default to normal close
⑤ DWELL TIME: 0-255 seconds is optional, default is 0 seconds
⑥ ACTIVATE AUS : on or off optional, default is off. When the alarm output is set to open, if there is an alarm input, the alarm signal
will be output and the alarm device, such as the alarm bell, will be activated.
⑦ CLEAR CURRENT ： In Figure 1-2-6, move the rocker up and down so that the cursor points to delete the current, and then move
the rocker to the right to delete the current alarm settings.
1.2.7 IR SETTING
In Figure 1-2-1, move the rocker up and down so that the cursor points to the IR setting, and then move the rocker to the right to
enter the IR setting menu. Figure 1-2-7 shows.
ALARM SETTING
NUMBER 1
ALARM ACT ACTION
INPUT TYPE CLOSE
OUTPUT TYPE CLOSE
DWELL TIME 0
ACTIVATE AUS OFF
CLEAR CURRENT
BCAK
EXIT
ALARM ACT SETUP
ACTION TYPE PRES
ACTION NUM 3
BACK
EXIT

17
MAIN CARMERA MENU
WHITE BAL AUTO
BACK LIGHT OFF
WDR OFF
FOCUS
ESPOSURE
SPECIAL
RESET
BACK
EXIT
IR SETTING
IR LED AUTO
NERA IR LED ----
MID IR LED ----
FAR IR LED
BACK
EXIT
Figure 1-2-7
① IR LED: auto, manual and off optional, default is auto. When set to auto, the PTZ camera can automatically turn on or off the
required IR lights according to the environment illumination and the camera multiples. The following three menu items can be
controlled only when the IR light is set to be manual.
② NERA IR LED: when the IR light is set to manual mode, the close range IR light can be set to turn on or off manually. When the
IR light is set to auto or off mode, the menu item is uncontrollable and the menu selection item shows "---".
③ MID IR LED: when the IR light is set to manual mode, the medium range IR light can be set to turn on or off manually. When the
IR light is set to auto or off mode, the menu item is uncontrollable and the menu selection item shows "---".
④ FAR IR LED: when the IR light is set to manual mode, the far range IR light can be set to turn on or off manually. When the IR
light is set to auto or off mode, the menu item is uncontrollable and the menu selection item shows "---".
1.3 CAMERA SETUP
In the menu of Figure 1-0-1, move the rocker up and down to point the cursor at the camera setup, and then move the rocker to
the right to enter the main menu of camera setup, as shown in Figure 1-3-1. Because the operation mode of main menu of PTZ
camera is different from camera setup menu, the operation mode of camera menu is explained here.
Basic operation of camera menu:
After entering the main menu of the camera, the rocker handle moves up and down to see the menu bar pointed by the cursor. If the
current menu bar is an optional menu item, moving the rocker handle left or right can change the current selection item. If the
current menu bar is followed by the symbol "8”, press [OPEN] to enter the menu item. Tip: the menu selection item is "---", which
means that the menu item is not optional.
FOCUS →(Figure 1-3-2)
ESPOSURE →(Figure 1-3-3)
SPECIAL →(Figure 1-3-4)

18
FOCUS SETUP
MODE AUTO
ZOOM SPEED HIGH
D-ZOOM
D-ZOOM RATE
BACK
EXIT
Figure 1-3-1
1.3.2 WHITE BAL
WHITE BAL: auto tracking white balance, manual, auto white balance →AUTO, outdoor, indoor, ATW
Option Description:
① AUTO: the camera automatically sets the value of camera white balance according to the current environment.
② ATW: in the case of complex light environment, a white paper is placed in front of the lens, and the image is displayed on a full
screen. Press [OPEN], the camera will set the base linear value of automatic white balance according to the current environment.
③ INDOOR: according to the indoor environment, the range of color temperature is 2300- 10500K Outdoor: according to the
outdoor environment, the range of color temperature is 1700-11000K.
④ OUTDOOR: This is an automatic compensation function to optimize the color of the camera in special environments, such as
mercury lighting environment. The range of color temperature is 2400-11000K.
1.3.3 BACK LIGHT
Back light compensation can be off or on. Default is off.
1.3.4 WDR
Dynamic detection can be turned on or off, default is off.
1.3.5 FOCUS
In Figure 1-3-1, move the rocker up and down so that the cursor points to focus, then press [OPEN] to enter the focus menu. As
shown in Figure 1-3-2.
Figure 1-3-2
① MODE: auto, one-push ,manual optional, default is auto. (Note: In camera model, the zoom-in and zoom-out menu is invalid.)
Option Description:
I AUTO: press [OPEN] to set zoom focus. When the picture changes, the camera will focus automatically.
II ONE-PUSH : set zoom focus by pressing [OPEN]. When the zoom multiples of the camera changes, the camera performs a
focusing action.

19
SPECIAL SETUP
DAY-NIGHT AUTO
DEFOG ---
IMAGE ADJ
DISPALY
OUTPUT
BACK
EXIT
ESPOSURES SETUP
MODE AUTO
AGC ---
IRIS ---
SHUTTER ---
3DNR OFF
BACK
E
XIT
III MANUAL: press [OPEN] to set zoom focus. The focus mode of the camera is manual and requires Focus Command focusing.
② ZOOM SPEED :high,low,middle optional , default is high.
Option Description:
I Manual: press [OPEN] to initialize the lens once.
II Auto: press [OPEN] to enter and set lens initialization cycle, the cycle can be selected 1-7 days.
1.3.6 ESPOSURE
In Figure 1-3-1, move the rocker up and down so that the cursor points to the esposure, and then move the rocker to the right to
enter the esposures setup menu. As shown in figure 1-3-3.
Figure 1-3-3
① MODE: default is auto, shutter pri/manual/iris pri optional.
② AGC: set the camera gain can affect the brightness of the image. off, manual, high, medium and low optional, default is high.
When set to manual, press [OPEN] to enter and set the manual gain. The gain can be 1-15dB.
③ IRIS : sens-up technology, used to improve the effect of low illumination image, but there will be the phenomenon of moving
image tailing. Off or auto optional, default is off. When choosing manual, press [OPEN] to enter and set sensitivity, and can choose
F1.6-F14.
④ SHUTTER: set the camera shutter. The default is that the menu item is not optional. At this time, the aperture menu item is
automatic.
Option Description:
Automatic shutter: the camera automatically adjusts the shutter according to the environment.
⑤ 3DNR: by setting this item, the noise of the camera picture is reduced, and the quality of the camera low illumination image is
increased. Option 1-5, default is off.
1.3.7 SPECIAL
In Figure 1-3-1, move the rocker up and down so that the cursor points to the special, and then press [OPEN] to enter the special.
As shown in figure 1-3-4.
IMAGE ADJ →(Figure 1-3-5)

20
Figure 1-3-4
① DAY-NIGHT: auto, color, B/W optional, default is auto
Option Description:
I Auto: the camera determine the color and B/W state according to its environment.
II Color: the camera set to color state
III B/W: the camera is set to black and white state.
In Figure 1-3-4 ， move the rocker up and down so that the cursor points to the IMAGE ADJ, and then press [OPEN] to enter the
IMAGE ADJ menu . As shown in figure 1-3-5
figure 1-3-5
I H-REV: on or off optional, default is off. When select on, horizontal image flip 180 degrees.
II V-REV : on or off optional, default is off. When select on, vertical image flip 180 degrees.
1.3.8 RESET
In Figure 1-3-1, move the rocker up and down to make the cursor point to reset, then press [OPEN] to reset the camera. When reset
is completed, it will be prompted "Reset is completed!"
1.4 USER ADMIN
In the menu of Figure 1-0-1, move the rocker up and down to point the cursor at the user admin, and then move the rocker to the
right to enter the user admin menu, as shown in Figure 1-4-1.
Figure 1-4-1
USER ADMIN
PRESET LOCK OFF
ENABLE PASSWORD OFF
EDIT PASSWORD
BACK
EXIT
IMAGE SETUP
H-REV OFF
V-REV OFF
FREEZE OFF
BACK
EXIT
EDIT PASSWORD → (Figure 1-4-2)