Comet Commeter C0111 User manual

Specifications are subject to change without notice i-com-n-Cxxxx-01
Portable digital devices
COMMETER Cxxxx
PRODUCT DESCRIPTION
Commeters of Cxxxx family are (depending on the device type) designed for measurement of temperature and relative humidity around the
device (or external probe), atmospheric pressure and the pressure tendency with the possibility of displaying the dew point temperature and
atmospheric pressure value corrected to the sea level. Measured values are displayed on a dual line LCD display. The measured values
(except pressure tendency) are compared with two adjustable levels for each measured quantity. Breaking the level is indicated by blinking
the proper value on display and by audio indication (switchable). Devices are equipped with memory of minimum and maximum values and
Hold function. Minimum and maximum values and Hold value are possible to display on the LCD anytime.
OPERATION
Switching ON and OFF the device
The device turns on and off with the button „ON/OFF“. Then the all symbols appear on the display to verify proper function.
Displaying of actual measured values
Use button „DISPLAY“ to select the actual measured values you wish to view on LCD display (does not apply to C0111 type).
device
C0111
C0121
C3120
C3121
C3121P
C3631
C3633
C4130
C4141
upper line
T1
T1
T
T
T
TINT
TINT
T
TEXT
T
temperature
lower line
---
T2
RV
RV
RV
RV
RV
RV
RV
RV
relative humidity
upper line
T1
T
T
T
TEXT
TEXT
P
TINT
P
atmospheric pressure
lower line
T1–T2
TDP
TDP
TDP
TDP
TDP
TDP
TDP
DP
dew point
upper line
TEXT
TEXT
„tEnd“
P
INT
internal sensor
lower line
TEXT –TDP
TEXT –TDP
TEND
TDP EXT
EXT
external sensor
upper line
„tEnd“
TEND
pressure tendency
lower line
TEND
Press button „HOLD”in the default mode (displaying of actual measured values) to store all actual measured values to internal memory. Press
„MIN” („MAX”) buttons (in the default mode) to display the minimum (maximum) value of the currently displayed measured quantity.
Functions and settings available from menu
Press button „MENU”to enter into the mode of viewing all menu items. The required item select using the arrow buttons. To return to the
default mode (displaying of actual measured values) press button „MENU”.
ALAr after pressing the button "ENTER" it is possible to set lower (ALLO) and upper (ALHI) limit for each measured quantity (except
pressure tendency). To set limits of the C0111 device press button “ALARM”.
AUdI by pressing the button „ENTER“ switch on (On) or switch off (OFF) audio signalling of alarm indication
CLr after pressing the button „ENTER“ is cleared memory of minimum and maximum values (this is confirmed by reading YES)
HOLd press the button „ENTER“ to display values stored in the HOLD memory (the measured quantity select by button „DISPLAY“)
bAt voltage value of partially loaded battery is displayed (this value illustrates battery condition)
CALC by pressing the button „ENTER" you enter into the mode of setting correction the atmospheric pressure to the sea level
d.rEF by pressing the button „ENTER“ select the fast (FASt) or dynamic (dYn) refresh mode
InFO gradual by pressing the button „ENTER“ are displayed: storing interval –the actual logging mode –the memory occupation –
service information about software version together with device configuration
BATTERY REPLACEMENT
Low battery voltage is indicated with blinking reading "BAT" on the display. It is necessary to replace battery with new one as soon as possible.
Battery is located under small cover on the instrument lower side. It is absolutely necessary to replace battery with instrument switched OFF.
Do not disconnect the button „ENTER” for longer than 1 minute even if instrument is switched OFF. If it happens (or if battery is totally
discharged), it is necessary to set again in appropriate menu selection LCD refreshment mode (d.REF.), alarm audio indication (AUDI) and
clear the memory of minimum and maximum values (CLR).
WARNING - It is not allowed to touch the sensors under the cover to prevent damage the sensors.
- The sensors (under the cover) should not be exposed to direct contact with water or other liquids.
- Do not connect or disconnect an external probe if the device is turned on (the incorrect value could be stored into
the memory of the minimum and maximum values).
- The sensors (under the cover) should not be exposed to direct contact with water or other liquid.
- Devices contain electronic components, it needs to liquidate them according to currently valid condition.
- To complement the information in this data sheet read the manuals and other documentations that are available
in the Download section for a particular device at www.cometsystem.com.

TECHNICAL SPECIFICATIONS
Device type
C0111
C0121
C3120
C3121, C3121P
C3631
C3633
C4130
C4141
Temperature measuring range - around the device
---
---
-10 to +60 °C
---
-10 to +60 °C
-10 to +60 °C
-10 to +60 °C
-10 to +60 °C
Temperature measuring range - surface contact probe
---
---
---
---
---
-10 to +60 °C
---
---
Temperature measuring range - external RH+T probe
---
---
---
-30 to +105 °C
---
---
---
-30 to +105 °C
Accuracy of temperature measurement
---
---
± 0.4 °C
± 0.4 °C
± 0.4 °C
± 0.4 °C
± 0.4 °C
± 0.4 °C
Temperature measuring range - Ni1000/6180 probe *
-50 to +250 °C
-50 to +250 °C
---
---
-50 to +250 °C
---
---
---
Relative humidity measuring range
---
X
---
5 to 95 %RH
0 to 100 %RH
5 to 95 %RH
5 to 95 %RH
5 to 95 %RH
0 to 100 %RH
Accuracy of humidity measurement **
---
---
± 2.5 %RH
± 2.5 %RH
± 2.5 %RH
± 2.5 %RH
± 2.5 %RH
± 2.5 %RH
Atmospheric pressure measuring range
---
---
---
---
---
---
800 to 1100 hPa
800 to 1100 hPa
Accuracy of atmospheric pressure measurement at 23 °C
°C
---
---
---
---
---
---
± 2 hPa
± 2 hPa
Dew point temperature measuring range
---
---
-40 to +60 °C
-60 to +80 °C
-40 to +60 °C
-40 to +60 °C
-40 to +60 °C
-60 to +80 °C
Accuracy of dew point temperature measurement ***
---
---
± 1.5 °C
± 1.5 °C
± 1.5 °C
± 1.5 °C
± 1.5 °C
± 1.5 °C
Temperature operating range of the device
-30 to +65 °C
-30 to +65 °C
-10 to +60 °C
-10 to +60 °C
-10 to +60 °C
-10 to +60 °C
-10 to +60 °C
-10 to +60 °C
Relative humidity operating range (without condensation)
5 to 95 %RH
5 to 95 %RH
5 to 95 %RH
5 to 95 %RH
5 to 95 %RH
5 to 95 %RH
5 to 95 %RH
5 to 95 %RH
Temperature operating range of the external probe
---
---
---
-30 to +105 °C
---
---
---
-30 to +105 °C
Relative humidity range of the external probe
---
---
---
0 to 100 %RH
---
---
---
0 to 100 %RH
Average current consumption from battery ****
0.08 to 0.3 mA
0.08 to 0.3 mA
0.15 to 0.7 mA
0.15 to 0.7 mA
0.2 to 0.8 mA
0.2 to 0.8 mA
0.3 to 1.3 mA
0.3 to 1.3 mA
Protection class
IP20
IP20
IP20
IP20
IP20
IP20
IP20
IP20
Weight without external probe
150 g
150 g
155 g
150 g
155 g
200 g
155 g
150 g
Dimensions [mm]
146 x 71 x 27
146 x 71 x 27
191 x 71 x 27
141 x 71 x 27
191 x 71 x 27
191 x 71 x 39
191 x 71 x 27
141 x 71 x 27
*
Accuracy including supplied probe
± 0.4 °C from -50 to +100°C
± 0.5 % from reading from +100 to +250 °C
Accuracy of the input (without probe)
± 0.2 °C from -50 to +100°C
± 0.2 % from reading from +100 to +250 °C
**
from 5 to 95 %RH at 23 °C
***
at temperature T < 25 °C and RH > 30 %
(for more details see graphs in the manuals)
****
the value of the average current consumption is in the mode
of FAST higher than in the mode of the dynamic
if you are using external ac/dc adapter 12 Vdc, the internal
battery 9V should be replaced with NiMH 9V accumulator