Comfort-n-Motion S31 User manual

with
the touch
of a button”
“Changing
your life
OWNER’S MANUAL—S31
R30190 REV 5

Safety Information
Attention! Important safety instructions. Please read
this manual thoroughly before using this product.
Electrical Safety
Always unplug this adjustable bed frame from the electrical outlet before any maintenance
or cleaning of the frame. To safely disconnect, make sure all of the controls are in the o
position, and then remove the plug from the outlet. To prevent re or shock hazard, do
not expose this unit to moisture. Keep the power cord away from heated surfaces. Do not
operate this adjustable bed frame and contact the manufacturer for repair if (1) it is not
working properly, (2) it has a damaged cord or plug, (3) it has been dropped or damaged or
(4) has been dropped into water.
Electrical Grounding
This product is equipped with a polarized or grounded electrical power cord. The power cord
will only t into a grounded, electrical surge protection device (not included) or a grounded
electrical outlet. The use of adapters is not recommended unless the outlet is checked by a
qualied electrician to ensure the proper grounding of the adapter.
For optimal safety, your adjustable bed should be plugged into a surge protector.
Electrical Rating
Input—100-240V, 50/60Hz, 1.6A; Output 29VDC, 2.0A
Battery Precautions
Please follow these precautions when using bat-
teries in this adjustable bed frame:
1. Danger of explosion if the battery is incorrectly replaced. Replace only with the
6LR61 9V batteries and LR03 AAA batteries.
2. Do not mix dierent types of batteries together (Alkaline, Rechargeable and
Carbon-Zinc) or old batteries with new batteries.
3. Be sure to follow the correct polarity when installing new batteries as indicated in
the battery compartment.
4. If the adjustable bed is not going to be used for a long period of time, remove
the batteries from the battery compartment to prevent damage or injury from
possible battery leakage.
5. Do not attempt to recharge a battery that is not intended to be recharged. This may
result in an overheating of the battery or rupture that could result in injury.
In Home Use & Hospital Disclaimer
Your adjustable bed frame is strictly designed for in-home use only. It is NOT designed for
hospital use and is NOT designed to meet hospital standards. Do not use this bed with TENT
TYPE oxygen therapy equipment or near explosive gases.
Lubrication and Cleaning
Your adjustable bed is designed to be maintenance free. The lift motors are permanently
sealed and lubricated, no additional lubrication is required. Do not apply any lubricant to lift
motor lead screws or any nylon nuts or the base may inadvertently creep downward from
the elevated position.
Warranty Warning
Please do not open any control box, motors or hand controls (with the exception of the
battery compartment, if equipped). The product warranty may be void if any of these
components are tampered with. Do not attempt to alter component wiring or adjust or
modify the structure of the product in any way or the warranty will be void. Only WSP can
authorize any repairs or replacement of parts on your adjustable bed.
Pets and Small Children Warning
Immediately dispose of all packing materials as it may pose a smothering risk to small
children and pets To avoid injury, it is not advised to allow children and small pets to play on
or under the bed. Children should not operate your adjustable bed without adult supervision.
Consumers with Pacemakers
Your adjustable bed may be equipped with a massage motor that produces a vibrating
motion. It is possible that some pacemakers may interpret this type of motion as a false
sense of movement and/or exercise. This may or may not aect your pacemaker. If you have
any concerns, please consult your physician.
Your adjustable bed also contains Neodymium (magnets) which may interfere with devices
such as pacemakers, ICD’s and any other device sensitive to magnetic elds. It is strongly
recommended that owners of such medical devices consult their physician prior to using
this product.
Product Ratings
The lift motors in your adjustable bed are NOT designed for continuous use. Reliable
operation and full life expectancy will be attained as long as the lift motors do not operate
more than 2 minutes over an 18 minute period, or approximately 10% duty cycle. To
ensure reliable functionality and full life of your adjustable bed, do not attempt to exceed
these limits. Attempting to circumvent or exceed this rating will shorten the life
expectancy of your adjustable bed and may void the warranty.
Acoustics
Your adjustable bed may contain the optional massage motor. This massage function will emit
a noticeable tone during operation. As the massage intensity level is increased, the volume
of the tone will increase. The volume of the tone is directly related to the location of your
adjustable bed. As an example, the surrounding environmental noise that might have been
present in the showroom where you purchased your adjustable bed could have covered
some of the noise from your adjustable bed massage motors. When your adjustable bed was
installed in your home you might notice an increase in volume in wood oorings or carpets.
In some normal base operations, you might notice some noise coming from the wheels which
allow your adjustable bed to maintain its distance from the wall. These wheels will make
contact with the steel platform supports of your adjustable bed creating a contact noise when
you enter, exit or shift weight while on the bed. This is normal.
FCC Compliance
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference; (2) This device must accept any interference received, including interference
that may cause undesired operation. To comply with the FCC RF exposure compliance
requirements, no change to the antenna or the device is permitted. Any change to the
antenna or the device could result in the device exceeding the RF exposure requirement and
void user’s authority to operate the device.
Radio Frequency is 2.4-2.48 GHz
Weight Restrictions
The structure of your adjustable bed will support the recommended weight when distributed
evenly across the bed. The adjustable bed is not designed to support or lift this amount in
the head or foot sections alone. You should enter and exit your adjustable bed with the
base in the at (horizontal) position. DO NOT STAND ON THE BASE AT ANY TIME.
DO NOT SIT ON THE HEAD OR FOOT WHILE IN THE RAISED POSITION.
The recommended weight limits are Twin/TwinXL/Full/FullXL/Split Queen/Queen/Split
Cal King/Split King: 850 lbs; Single Piece King 650 lbs. Exceeding this weight restriction
could damage the bed and/or cause injury and will void the warranty.
Moving After Installation
Do not place adjustable bed base vertically on its head or foot sections. This may cause
injury to persons or damage to the base.
Fabric Cleaning Information
Spot clean only with a water based shampoo or a foam upholstery cleaner. Pretest a small,
inconspicuous area before proceeding. Do not over wet or use solvents to spot clean. Hot
water extraction or steam cleaning is not a recommended cleaning method. To prevent overall
soiling, frequent vacuuming or light brushing with a non-metallic sti bristle brush to remove
dust or grime is recommended.
PLEASE SAVE THIS MANUAL!

User Information
Please take a moment and write down the serial number in the space
provided below, in case you need to refer to it in the future. This
information can be found on the side of the power supply, on the
underside of the adjustable base, on the outside of the box on the
main label and on the warranty registration card.
Model # S31
Serial Number:
Page 2
Contents
Customer Care
Toll Free 888-846-3840
Email: [email protected]
Safety Information 1
Weight Restrictions 1
Cleaning 1
Parts List 3
Base Assembly 4
Synchronization & Resetting Base’s Electronics 5
Location of Controls on Remote 7
Troubleshooting 8
Warranty 9
Warranty Registration Form 10
NOTE: All pictures in this manual are shown for illustration
purposes only and may not be an exact representation of the
product. Actual product may vary due to product enhancement.

Parts List
Note: the 8” legs are
(2) 4” legs combined.
If you prefer a low
profile bed you may
remove the 4” top
section.
8” Legs (Qty. 4)
NOTE: BEFORE DISCARDING ANY PACKING
MATERIALS, CHECK THE CARDBOARD BOX
OF THE ADJUSTABLE BED AND VERIFY THE
FOLLOWING ITEMS ARE INCLUDED.
ALL ELECTRONICS AND COMPONENTS THAT
NEED TO BE INSTALLED ARE LOCATED IN
BOXES UNDER THE BASE OR ATTACHED TO
THE ADJUSTABLE BED FRAME.
Page 3
Remote Control
with AAA Batteries (1)
Mattress Retainer Brackets Kit (1)
Power Supply (1)
Connecting Strap (1)
(Only included with
Twin XL and Cal King)
Tools
needed
When using your
own headboard:
Plain screwdriver
and a 7/16”
wrench Bluetooth Module (Optional)
To control adjustable bed
remotely with your smart device.
Sync Cable (1)
(Only included with
Twin XL and Cal King)

Step 1
It is highly recommended to use two people
for the installation of this product. Before
assembly, place the unit in the appropriate
nal position to make the assembly process
easier. The unit should be placed top side
down on the oor according to the box
instructions. Remove the 2 boxes included and
untie the mattress retainer.
Step 2
Screw in the provided legs (4) in each corner of the base rota-
ting clockwise until tight. DO NOT OVERTIGHTEN THE
LEGS.
Step 3
Untie and remove the twist ties
from the cables and release the
DC cord.
Step 5
Insert the AC cord into the Power
Supply and lock it using the clip.
DO NOT PLUG BASE INTO
THE POWER OUTLET YET.
Step 4
Plug the two 9 volt batteries
(included) in the compartment of
the Power Supply and insert the
cover to close.*
NOTE: THESE BACKUP BATTERIES WILL ALLOW THE BED TO BE LOWERED IF A POWER OUTAGE
OCCURS. IT IS RECOMMENDED NOT TO DO ANYTHING EXCEPT TO LOWER THE BED AS THE BATTERY
BACKUP WILL NOT ELEVATE THE BED SECTIONS.
*It is recommended to replace the two 9 volt batteries every 12 months.
Base Assembly Page 4