Comfort Products 50-100505 User manual

ASSEMBLY INSTRUCTIONS
SUPPLIER CODE - HMOF
OneSpace is a Trademark of Comfort Products, Inc.
™

2
ITEMS ARE NOT SHOWN TO SCALE.
PARTS LIST PAGE 1 OF 2
PART
DESCRIPTION FRONT BACK
STOCK #
QTY.
1 Desk Top 51-100505DT 1
2 Keyboard Tray 51-100505KT 1
3 Printer Shelf 51-100505PS 1
4 Bottom Shelf 51-100505BS 1
5 Back Board 51-100505BB 1
6 Book Shelf 51-100505KS 1
7 Cabinet Top
51-100505CBT
1
8 Cabinet Base
51-100505CBS
1
9 Cabinet Wall 9
51-100505CW9
1
10
Cabinet Wall
10
51-100505CW10
1
11 Cabinet Back
51-100505CBK
1

ITEMS ARE NOT SHOWN TO SCALE.
PARTS LIST PAGE 2 OF 2
PART
DESCRIPTION FRONT
BACK
STOCK #
QTY.
12
Small Drawer
Front
51-100505SDF
1
13
Small Drawer
Left
51-100505SDL
1
14
Small Drawer
Right
51-100505SDR
1
15
Small Drawer
Back
51-100505SDB
1
16
Drawer
Bottom
51-100505DB 2
17
Large Drawer
Front
51-100505LDF
1
18
Large Drawer
Left
51-100505LDL
1
19
Large Drawer
Right
51-100505LDR
1
20
Large Drawer
Back
51-100505LDB
1
BACK
3

4
PARTS LIST (CONT’D) HARDWARE PARTS LIST
PART DESCRIPTION STOCK# QTY.
21 Right Stand 51-100505RS 1
22 Rear Bar 51-100505RB 1
23 Brace 51-100505BRC 1
24 Posts with Rollers 51-100505PR 1
25 Rectangle Post 51-100505REP 2
26 Extender 51-100505EX 2
27 Hanger 51-100505HG 1
28
Drawer Handle 51-100505DH 229
Caster 51-1005CAST 4
30 Printer Stand
Fastener 51-1005PSF 2
31 Leg Cap 51-1005LC 2
PART DESCRIPTION QTY
32 Disk 51-1005DK 4
33 Printer Stands 51-1005PST 1 pair
34a
Drawer Rollers 51-1005ROLLERS
4
ACam 16
BCam Lock 16
C M5 x 60MM 12
D M5 x 70MM 2
2
E M6 x 30MM 3
F M6 x 40MM
G M4 x 18MM 4
H M4 x 35MM 8
IM4 x 12MM 36
JM6 x 80MM 2
K M6 x 10MM 12
L M6 x 30MM 4
M Hex Wrench 1
EXTRA HARDWARE IS INCLUDED FOR YOUR CONVENIENCE
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED.
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE THE TOOL BELOW BEFORE YOU BEGIN ASSEMBLING.
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
- THE FOLLOWING TOOL IS NOT INCLUDED.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
REPLACEMENT PARTS
IF YOU ARE MISSING ANY OF THE PARTS ABOVE, OR IF YOU HAVE A
DAMAGED PART, PLEASE VISIT WWW.COMFORTPRODUCTS.NET/SUPPORT
AND REFERENCE THE MODEL # ON THE FRONT OF THIS MANUAL. SIMPLY
COMPLETE THE INFORMATION, INCLUDING THE PART YOU NEED. THE
PART WILL NORMALLY SHIP WITHIN 48 HOURS.
HARDWARE KIT
STOCK # 51-1005HA
34b
4

I x 8
5
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 1
Separate each of the four rollers (34) into its two parts (34a) and (34b) as shown.
Attach rollers (34b) to panels (13), (14), (18) and (19) using screws (I).
Each roller should be placed on the side opposite to the groove.
STEP 2
34a
34b
34b
18
34b
19
34b
13
34b
14
34b
34b
34a
I
I
I
I
I
I
I
I
I
I

6
B x 8
A x 8
STEP 3
Insert the cam locks (B) into panels (13), (14), (18) and
(19). Make sure the cam lock opening is facing the
outer holes.
STEP 4
STEP 5
Caution:
Do not over tighten
cams.
M
A
B
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
14
18
17
12
14
13
12
17
18
19
AA
19
13
Insert the cams (A) into panels (17) and (12).
Make sure all cams are screwed in securely.
Connect the drawer fronts (12) and (17) using cams (A). Turn the
cams about 1/2 turn clockwise to lock into place.

H x 8
I x 8 34a
G x 4
7
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 8
STEP 6
STEP 7
12
17
9
10
27 x 1
29 29
G
G
34a
34a
34a
34a
I
I
I
I
I
I
I
I
I
I
16
15
20
27
16
Attach drawer handles (29) to (12) and (17) using screws (G) as shown.
Insert drawer bottom (16) into the grooves of small drawer. Attach drawer back (15) using screws (H).
Insert drawer bottom (16) into grooves of large drawer. Insert hangers (27) as shown.
Attach drawer back (20) using screws (H).
Attach four rollers (34a) to cabinet walls (9) and (10) using screws (I).

D x 2
B x 4
A x 4
STEP 10
Insert cam locks (B) into panels (9) and (10) as shown.
Attach (9) and (10) to cabinet base (8) using cams (A) as shown.
Turn cam locks to lock into place.
8
STEP 9
Attach casters (28) to bottom of cabinet base (8) using screws
(I) as shown.
Attach cam (A) to top of cabinet base (8)
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 11
Attach leg caps (31) to right stand (21) as shown.
STEP 12
Attach bottom shelf (4) to right stand (21) using screws (D)
as shown.
Caution:
Do not over tighten
cams
M
A
B
D
31 x 2
31
4
8
910
I
I
I
I
8
I x 16
21
28
28
28
28
A
A
A
A
A
A
A
A
B
21

E x 2 F x 2
E x 1 C x 8
23
E
9
STEP 14
Attach rear bar (22) using two screws (F).
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 13
Attach brace (23) to (4) using screws (E).
STEP 15
Connect back board (5) and book shelf (6) to frame using eight
screws (C) and one screw (E).
Caution: DO NOT OVER TIGHTEN SCREWS
C
C
C
C
C
C
C
C
E
6
5
4
F
F
22

7
1
25
24
1
C
C
K x 8
L x 4
STEP 19
A x 4
STEP 18
Attach four cams(A) to cabinet top panel (7).
32 x 4
10
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 16
Attach cabinet back (11) using four screws (C).
STEP 17
Turn desk top (1) upside-down. Attach (24) and (25) using
eight screws (K).
NOTE: make sure the position of the rollers on part (24)
matches the diagram.
C x 4
11
7
K
K
K
K
A
A
A
A
L
L
32
32 32
32
Rollers
Attach cabinet top (7) using disks (32) and screws (L).

Caution:
Do not over tighten
cams.
M
A
B
K x 4
B x 4 J x 2 26 x 2
11
STEP 21
Attach printer stands (33) to printer shelf (3) using four
screws (K).
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 20
STEP 22
You may position the printer stands anywhere on the rear
of the desk. Simply secure to desk top using fasteners (30).
30 x 2
3
21
J
J
1
B
B
26
7
ver tighten
STEP 22
21
J
J
1
B
B
26
7
ver tighten
STEP 22
J
1
B
B
26
7
ver tighten
STEP 22
21
J
J
1
B
B
26
7
ver tighten
STEP 22
1
7
910
30
AAAA
J
J
B
B
21
26
K
K
K
K
33
Insert cam locks (B) into cabinet walls (9) and (10).
Insert extenders (26) into right stand (21).
Carefully place desktop (1) onto desk frame.
Tighten cam locks (B) and attach two screws (J).

2
I x 4
12
DO NOT TIGHTEN SCREWS UNTIL COMPLETELY ASSEMBLED
STEP 24
Attach keyboard tray (2) using four screws (I).
STEP 23
Install assembled cabinet drawers.
I
I

SAFETY AND MAINTENANCE
• DO NOT stand on the desk. Do not use the desk as a stepladder.
•
• Every 6 months, check all bolts and screws to ensure they are tight.
• This product is California 93120 Compliant for Formaldehyde.
LIMITED WARRANTY
PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION
13
Comfort Products warrants this product to be free from defects in material and workmanship for
1 year. This warranty is made by Comfort Products only to the original end-user customer acquiring
the product directly from Comfort Products’ authorized dealers as shown by the original sales receipt.
The end-user customer remedy pursuant to this warranty is limited to repair or replacement of parts
at Comfort Products’ option within a reasonable amount of time. Comfort Products reserves the right
to require damaged parts to be returned to Comfort Products upon request. Consent from Comfort
Products must be obtained before any warranty work is performed. This warranty shall not apply to any
products which must be replaced because of normal wear and tear, negligence, abuse, or “accident”.
This warranty applies under conditions of normal use and is not subject to defects caused by improper
of transportation or labor. In no event shall Comfort Products be liable in either tort or contract for any
loss or direct, special, incidental, consequential or exemplary damages. This Limited Warranty is NOT
applicable to end-user customers who use Comfort Products for rental purposes. This warranty applies
only to end-user customers in the United States. All warranties are limited to the original purchaser
For claims or questions concerning this warranty, please visit www.comfortproducts.net/support or
e-mail us at [email protected].
MODEL: 50-100505. Made in China.
OneSpace is a Trademark of Comfort Products, Inc.
™
for normal use. The weight capacity is 100 pounds for the desktop and 15 pounds for the drawers.
Comfort Products, Inc.
122 Gayoso Avenue, Suite 101
Memphis, TN 38103
email: [email protected]
www.comfortproducts.net