Comfort Products 50-512OK User manual

HARDWARE KIT
STOCK # 51-512HAOK
PART DESCRIPTION QTY.
PART DESCRIPTION QTY.
STOCK NO. PART DESCRIPTION QTY. STOCK NO.
2 OF 10
REPLACEMENT PARTS
IF YOU ARE MISSING ANY OF THE PARTS ABOVE, OR IF YOU HAVE A DAMAGED PART, PLEASE VISIT WWW.COMFORTPRODUCTS.NET/SUPPORT
REFERENCE THE MODEL # ON THE FRONT OF THIS MANUAL. SIMPLY COMPLETE THE INFORMATION, AND THE PART YOU NEED. THE PART WILL
NORMALLY BE SHIPPED WITHIN 48 HOURS
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED .
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE THE TOOLS BELOW BEFORE YOU BEGIN ASSEMBLING.
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
- DO NOT SHIFT OR DRAG THE PRODUCT AFTER ASSEMBLY.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE FURNITURE WAX OR POLISH AS THE
UNIT IS FINISHED WITH A LAMINATE PAPER FOIL.
A
B
C
D
E
F
G
top panel 51-512OKC
51-512OKA
Left side
panel 1
Right side
panel 51-512OKB 1
bottom panel
51-512OKD
1
2
center top panel
51-512OKE 1
center panel
center panel
51-512OKF
51-512OKG
1
1
Hcenter bottom
panel 51-512OKH 1
Idesktop 51-512OKI
1
JLower front
panel 51-512OKJ 1
Kdesktop bottom
panel 51-512OKK 1
- THE FOLLOWING TOOLS ARE NOT INCLUDED.
#1
#2
#3
#4
#5
#6
#7
#8
#9
*Please look for part number on the side of the part. It either is stamped or has a labeled sticker.

5 OF 10
Step 3:
Step 4:
Screw panel (A & B) to panel (D) with four Unitar screw (3). Then screw panel (D) to panel (H)
with two CSK screw (4) using predrilled holes.
X 4pcs
Screw panel (E) to panel (A), (B) & (H) With six Unitar screws (3) using predrilled holes. (Make sure cam
holes are facing inward as shown in the image).
X 6pcs
X 2pcs
Part # 3
Part # 3
Part # 4
3
4
3

6 OF 10
Step 5:
Step 6:
X 2pcs
X 6pcs
X 2pcs
Attach desktop bottom panel (K) to panel (D) by aligning the two Minixes (2)
into predrilled holes on panel (K). Then press the two Cams (5) to the bottom of Cam holes,
making sure the arrow on top of each cam is pointed towards the Minixes.
Turn the Cam clockwise to lock the cam into the Minix.
Attach lower front panel (J) to the desktop bottom panel (K) with two Unitar screw (3).
Then using a rubber hammer, hammer the six nail leg (6) to the bottom of panels (E and J).
Part # 5
Part # 3
Part # 6
6
3
2
Caution:
Do not over tighten
cams.

7 OF 10
Step 7:
Step 8:
X 2pcs
X 4pcs
X 2pcs
Invert desk to upright position, and attach desktop (I) by aligning the two Minix (2)
on the bottom of the desk into the predrilled holes in panel (J). Then press the two Cams (5)
to the bottom of Cam holes, making sure the arrow on top of each cam is pointed towards the
Minixes. Turn the Cam clockwise to lock the cam into the Minix. Then x four Unitar screw (3)
to panels (A & B) using predrilled holes.
Attach center panel (G) to the desktop (I) aligning the two Minix (2).
Then press the two Cams (5) to the bottom of Cam holes,
making sure the arrow on top of each cam is pointed towards the Minixes.
Turn the Cam clockwise to lock the cam into the Minix.
Part # 3
Part # 5
3
Part # 5
2
2
2
Caution:
Do not over tighten
cams.
Caution:
Do not over tighten
cams.

8 OF 10
Step 9:
Step 10:
X 2pcs
X 4pcs
X 2pcs
Attach center panel (D) to center panel (G) by xing two CSK screw (4) in predrilled holes .
Then x four Unitar screw (3) to panels (A & B) to secure panel (D).
Attach center top panel (F) by aligning the two Minix (2) from panel (D) into predrilled holes.
Then press the two Cams (5) to the bottom of Cam holes, making sure the arrow on top of each
cam is pointed down towards the Minixes. Turn the Cam clockwise to lock the cam into the
Minix.
Part # 3
Part # 4
Part # 5
4
3
1
2
Caution:
Do not over tighten
cams.

9 OF 10
Step 11:
Step 12:
X 14pcs
X 6pcs
Attach top panel (C) by aligning the six Minix (2) into predrilled holes on top of desk.
Then press the six Cams (5) to the bottom of Cam holes, making sure the arrow on top of each
cam is pointed up towards the Minixes. Turn the Cam clockwise to lock the cam into the
Minix.
Place Unitar screw caps and cam caps over their respective part.
Part # 5
X 6pcsPart # 8
Part # 7
8
7
2
7
87
Caution:
Do not over tighten
cams.

• DO NOT stand on the desk. Do not use the desk as a stepladder.
•
• Every 6 months, check all bolts and screws to ensure they are tight.
• This products is California 93120 Compliant for Formaldehyde
10 OF 10
PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR W ARRANTY INFORMATION
Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This warranty is made by
Comfort Products only to the original end-user customer acquiring the product directly from Comfort Products' authorized dealers
as shown by
the original sales receipt. The end-user customer remedy pursuant to this warranty is limited to repair or replacement of
parts at Comfort
Products' option within a reasonable amount of time. Comfort Products reserves the right to require damaged parts
to be returned to Comfort Products upon request. Consent from Comfort Products must be obtained before any warranty work is
performed. This warranty applies under conditions of normal use and does not subject to defects caused by improper assembly or
disassembly; defects occurring after purchase due to product modi cation, intentional damage, re, misuse, negligence, or exposure
to the elements;
labor or assembly cost. This warranty does not cover the cost of transportation or labor . In no event shall Comfort
Products be liable in either tort or contract for any loss
or direct, special, incidental, consequential or exemplary damages. This Limited
Warranty
is NOT applicable to end user customers who use Comfort Products for rental purposes. This warranty applies only to end-
user customers in the United States.
All warranties are limited to the original purchaser for normal use. The weight capacity is de ned 200
pound s for the table and 30 pounds for the shelves. For claims or questions concerning this warranty, please visit:
www.comfortproducts.net or e-mail us at: [email protected]
MODEL: # 50-512OK
Comfort Products, Inc.
P.O. Box 999
Memphis, TN 38101
www.comfortproducts.net
[e-mail]