Commell LE-365 User manual

LE-365
3.5 inch Miniboard
User’s Manual
Edition 1.0
2007/05/03

LE-365 User’s Manual
2
Copyright
Copyright 2007. All rights reserved. This document is copyrighted and all rights are
reserved. The information in this document is subject to change without prior notice to make
improvements to the products.
This document contains proprietary information and protected by copyright. No part of this
document may be reproduced, copied, or translated in any form or any means without prior
written permission of the manufacturer.
All trademarks and/or registered trademarks contains in this document are property of their
respective owners. Disclaimer
The company shall not be liable for any incidental or consequential damages resulting from
the performance or use of this product.
The company does not issue a warranty of any kind, express or implied, including without
limitation implied warranties of merchantability or fitness for a particular purpose.
The company has the right to revise the manual or include changes in the specifications of
the product described within it at any time without notice and without obligation to notify any
person of such revision or changes.
Trademark
All trademarks are the property of their respective holders.
Any questions please visit our website at TUhttp://www.commell.com.twUT

LE-365 User’s Manual
3
Packing List
Please check the package before you starting setup the system
Hardware:
LE-365 miniboard x 1
Cable Kit:
44-pin
40-pin
44-pin
1 to 3 power output cable
ATA33 IDE Cable x1
DC Power Cable x 1
SATA Power Cable x 1
PS/2 Keyboard & Mouse Cable x 1
SATA Cable x 2
DVI module with bracket x1
(LE-365D Only)
COM Port Cable x 1
USB Cable x 1
Audio Port Cable x 1
Printed Matters:
Driver CD x 1（including User’s Manual）

LE-365 User’s Manual
4
Index
Chapter 1 <Introduction>................................................7
1.1 <Product Overview>.................................................................................7
1.2 <Product Specification>...........................................................................8
1.3 <Mechanical Drawing>...........................................................................10
1.4 <Block Diagram>....................................................................................11
Chapter 2 <Hardware Setup>.......................................12
2.1 <Connector Location>............................................................................12
2.2 <Jumper Reference> .............................................................................14
2.3 <Connector Reference>.........................................................................15
2.3.1 <Internal Connector>..................................................................15
2.3.2 <External Connector>.................................................................15
2.4 <CPU and Memory Setup>....................................................................16
2.4.1< CPU>........................................................................................16
2.5 <CMOS ATX Setup>..............................................................................17
2.6 <Enhanced IDE & CF interface>............................................................18
2.7 <Serial ATA Interface>...........................................................................19
2.9.1 <Analog VGA Interface> ............................................................20
2.9.2 <Digital Display>.........................................................................21
2.9.3 <DVI Interface > .........................................................................25
2.10 <Onboard Audio Interface>..................................................................26
2.11 <USB2.0 Interface>..............................................................................27
2.12 <GPIO Interface>.................................................................................29
2.13 <Serial Port Jumper Setting >..............................................................30
2.15.1 <Power Input>..........................................................................32
Remark: DC input voltage range 8~24V..................................................32
2.14.2 <Power Output> .......................................................................33
2.14.3 <Fan Connector>.....................................................................33
2.15 <Indicator and Switch>.........................................................................34

LE-365 User’s Manual
5
Chapter 3 <System Setup>...........................................36
3.1 <Display Configuration>.........................................................................36
Chapter 4 <BIOS Setup>...............................................39
Appendix A <I/O Port Pin Assignment>......................41
A.1 <IrDA Port>............................................................................................41
A.2 < CRT Port >..........................................................................................41
A.3 <Serial ATA Port>..................................................................................41
A.4 <Serial Port>..........................................................................................42
A.5 <LAN Port>............................................................................................42
Appendix B <Flash BIOS>............................................43
B.1 BIOS Auto Flash Tool .....................................................................43
B.2 Flash Method...................................................................................43
Appendix C <System Resources>...............................44
Contact Information ......................................................49

LE-365 User’s Manual
6
(The Page is Left For Blank)

LE-365 User’s Manual Introduction
Product Overview
7
Chapter 1 <Introduction>
1.1 <Product Overview>
LE-365 is the 3.5 inches embedded miniboard based on VIA CX700M platform, with
onboard VIAEden 1G processor, VGA, LAN, Audio, USB2.0, CF, LVDS. The board provides
economic fanless solution for multimedia applications.
VIA CX700M Chipset
The board integrates VIA CX700M, to provide built-in UniChrome Pro 3D / 2D Graphics with
MPEGII/MPEG4 decoder, and supports DDR400/533 memory up to 1G of capacity. The
CX700M has Ultra V-Link Host interface with 1 GB/sec total bandwidth to enhance the
system performance.
18/24-bit LVDS LCD interface
The board provides onboard 18/24-bit LVDS LCD interface, supports up to 1600 x 1200 of
UXGA high resolution.
Flexible Extension Interface
The board also provides Compact Flash Type II socket and two mini-PCI socket.

LE-365 User’s Manual Introduction
Product Specification
8
1.2 <Product Specification>
General Specification
Form Factor 3.5 inches embedded miniboard
CPU Embedded VIA V4 Eden 1G processor
Front side bus: 400MHz
Fanless with heatsink only
Memory 1 x 200-pin DDR2 400/533 SO-DIMM SDRAM up to 1GB
Unbufferred, none-ECC memory supported only
Chipset VIA CX700M
BIOS Phoenix-Award v6.00PG 4Mb PnP flash BIOS
Green Function Power saving mode includes doze, standby and suspend modes.
ACPI version 1.0 and APM version 1.2 compliant
Watchdog Timer System reset programmable watchdog timer with 1 ~ 255
sec./min. of timeout value
Real Time Clock CX700M integrated RTC with lithium battery
Enhanced IDE Enhanced UltraDMA133 IDE interface supports dual channels
and up to 2 ATAPI devices
One 44-pin IDE port onboard
Serial ATA CX700M integrates 2 Serial ATA interfaces
(No RAID Function)
Up to 300MB/s of transfer rate
Multi-I/O Port
Chipset VIA CX700M with Winbond® W83697HG controller
Serial Port One RS-232/422/485 serial port
USB Port Two external & two internal Hi-Speed USB 2.0 ports with
480Mbps of transfer rate
IrDA Port One IrDA compliant Infrared interface supports SIR
K/B & Mouse PS/2 keyboard and mouse port
GPIO One 12-pin Digital I/O connector with 8-bit programmable I/O
interface
VGA Display Interface
Chipset VIA CX700M built-in S3 Graphics UniChrome Pro IGP graphics
core
Core Frequency 200MHz
Memory BIOS selectable 16/32/64/128MB shard with system memory
Display Type CRT, LCD monitor with analog display
Connector External DB15 female connector on rear I/O panel
LCD Interface
Chipset VIA CX700M transmitter
Interface 18/24-bit LVDS interface
12V backlight inverter connector

LE-365 User’s Manual Introduction
Product Specification 9
Panel voltage 3.3V/5V jumper selectable
Ethernet Interface
Chipset Realtek RTL8110S-32 Gigabit Ethernet controller
Type 10/100/1000 Base-TX
auto-switching Fast Ethernet
Full duplex, IEEE802.3U compliant
Connector External RJ45 connectors with LED on rear I/O panel
Audio Interface
Chipset VIA VT1708A
Interface 2 channel HD audio with Line-out and MIC-in
Connector External Audio phone jack for Line-out
Onboard audio connector with pin header
Onboard CD-IN connector
Expansive Interface
Mini-PCI 2 x 32-bit 5V/3.3V Mini-PCI socket
Solid State Disk
DOM IDE1 supports 44-pin DOM (DiskOnModule)
CompactFlash 1 x CompactFlash Type 2 socket
Power and Environment
Power
Requirement DC 8V~24V input
1 x 2-pin DC_IN connector onboard
Dimension 146 (L) x 101 (H) mm
Temperature Operating within 0 ~ 60PP
oPPC (32 ~ 140PP oPPF)
Storage within -20 ~ 85PP
oPPC (-4 ~ 185PP oPPF)
Ordering Code
LE-365D Onboard VGA, 1x Gigabit LAN, 4 x USB2.0, 1 x CF, 2 x MinPCI,
HD Audio, 1 x Irda, DVI and HDTV(optional)
LE-365X Onboard VGA,1x Gigabit LAN, 4 x USB2.0, 1 x CF , 2 x MinPCI,
HD Audio ,1 x Irda, LVDS and HDTV(optional)

LE-365 User’s Manual Introduction
Mechanical Drawing
10
1.3 <Mechanical Drawing>

LE-365 User’s Manual Introduction
Block Diagram
11
1.4 <Block Diagram>
Eden nanoBGA2
CRT/LCD Monitor
1 x 200-pin SO-DIMM
DDR2 400/533MHz
up to 1GB
CX700M
LVDS or DVI
ICH7-M
VT 1708A 2 x SATA
CompactFlash＆IDE
4 x USB2.0 ports
BIOS
LPC
83697HG RTL8110S-32
2 x Serial ports
8-bit GPIO 2 x MINI PCI
PS/2 KB/MS
IrDA

LE-365 User’s Manual Hardware Setup
Connector Location
12
Chapter 2 <Hardware Setup>
2.1 <Connector Location>
（1）LE-365X CN_LVDS
CPUFAN
DC_IN
SYSFAN JFRNT
IDE
DC_OUT
CN_INV
MINIPCI2
CF
CN AUDIO
CN_USB2
（2）LE-365D
CN_IR
CD_IN
CN_DIO
SATA1/2 CN_COM2
CN_DVI
CPUFAN
SYSFAN
CN_IR
MINIPCI2
CD_IN
CN AUDIO
CN_DIO SATA1/2
JFRNT
DC_OUT
CN_COM2
CN_USB2
CF
DC_IN
IDE

LE-365 User’s Manual Hardware Setup
Connector Location 13
RJ45 PS2 USB CRT COM1
DDRII
MINIPCI1

LE-365 User’s Manual Hardware Setup
Jumper Reference
14
2.2 <Jumper Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JVLCD LCD Panel Voltage Setting
JAT AT Mode
JCSEL1/2 COM2 RS232/422/485 mode setting
JVLCD
JAT
JRTC
JCSEL1
JCSEL2

LE-365 User’s Manual Hardware Setup
Connector Reference 15
2.3 <Connector Reference>
2.3.1 <Internal Connector>
Connector Function Remark
DDRII 200 -pin DDR2 SO-DIMM SDRAM slot
SATA1/2 7-pin Serial ATA connector
CN_AUDIO 5 x 2-pin audio connector
CD_IN 4-pin CD-ROM audio input connector
CN_DIO 6 x 2-pin digital I/O connector
CN_USB2 5 x 2-pin USB connector
CPUFAN 3-pin CPU cooler fan connector
SYSFAN 3-pin system cooler fan connector
CN_COM2 5 x 2-pin com connector
CN_IR 5-pin IrDA connector
CF Compact Flash Type II socket
CN_LVDS 20 x 2-pin LVDS connector LE-365X
CN_INV 5-pin LCD inverter connector LE-365X
DC_OUT 4-pin power output connector
DC_IN 3-pin power input connector
MINIPCI1/2 Mini-PCI socket
CN_DVI 13 x 2-pin DVI interface LE-365D
JFRNT 14-pin switch/indicator connector
2.3.2 <External Connector>
Connector Function Remark
CRT DB15 VGA connector
USB Dual USB 2.0 connector
COM1 DB9 Serial port connector
RJ45 One RJ45 LAN connector
PS2 PS/2 keyboard and mouse connector

LE-365 User’s Manual Hardware Setup
CPU and Memory Setup
16
2.4 <CPU and Memory Setup>
2.4.1< CPU>
The board comes with the VIA V4 Eden 1GHz processor , it supports new generation of
VIA V4 Eden 1GHz processor with 400MHz of front side bus and 2MB L2 cache. Please
follow the instruction to install the CPU properly.
2.4.2 <Memory>
The board provides one 200-pin DDR2 SO-DIMM to support DDR2 400/533 memory
modules up to 1GB of capacity. Non-ECC, unbuffered memory is supported only. While
applying two same modules, dual channel technology is enabled automatically for
higher performance.
DDRII

LE-365 User’s Manual Hardware Setup
CMOS ATX Setup 17
2.5 <CMOS ATX Setup>
The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to
inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its
default values.
Jumper: JRTC
Type: Onboard 3-pin jumper
JRTC Mode
1-2 Clear CMOS
2-3 Normal Operation
Default setting 2-3
Jumper: JAT
Type: onboard 3-pin header
JAT Mode
1-2 AT Mode
2-3 ATX Mode
Default setting 2-3
JAT
3
1
3 1
JRTC

LE-365 User’s Manual Hardware Setup
Enhanced IDE&CF Interface
18
2.6 <Enhanced IDE & CF interface>
The board supports one UltraDMA133 IDE interface, and one CompactFlash Type II socket
with secondary IDE mode, the 44-pin IDE connector can support up to 2 ATAPI devices
through IDE cable, and the CompactFlash socket can support IDE DMA mode (depends on
the CF card specification).
43 1
2
44
IDE
CF

LE-365 User’s Manual Hardware Setup
Serial ATA Interface 19
2.7 <Serial ATA Interface>
Based on VIA CX700M, the board provides two Serial ATA interfaces with up to 300MB/s of
transfer rate.
SATA1/2
2.8 <LAN Interface>
The Realtek RTL8110S-32 supports triple speed of 10/100/1000Base-T, with IEEE802.3
compliance and Wake-On-LAN supported.
LAN

LE-365 User’s Manual Hardware Setup
Onboard Display Interface
20
2.9 <Onboard Display Interface>
Based on VIA CX700M chipset with built-in GMA (Graphic Media Accelerator) 950 graphics,
the board provides one DB15 connector on real external I/O port, and one 40-pin LVDS
interface with 5-pin LCD backlight inverter connector. The board provides dual display
function with clone mode and extended desktop mode for CRT and LCD or DVI .
2.9.1 <Analog VGA Interface>
Please connect your CRT or LCD monitor with DB15 male connector to the onboard DB15
female connector on rear I/O port.
CRT