Commlite CM-ENF-E1 PRO Use and care manual

Commlite Lens Mount Adapter from Nikon F Lens to Sony E-Mount
CM-ENF-E1 PRO Firmware Upgrading Instruction
Upgrading Content
The Newest Firmware: Ver. 06 _2016.09.28 （Windows Only）
Notice:
Upgrade CM-ENF-E1 PRO from Ver.05 to Ver.06
Upgrading Details：
V06 Firmware Upgrading Content:
1. Compatible with SONY A9;
2.Compatible with following new lens:
AF-S 24-70mm f/2.8E ED VR
AF-S 70-200mm f2.8E FL ED VR
AF-S 105mm f/1.4E
85MM f/1.4 ART
135mm f/1.8 ART
Notice：V06 version lens list(it is quite possible working with the adapter which
is not including in the table, but we can't guarantee its compatibility and
performance.
Notice Before Upgrade
1. Make sure whether your lens need to be upgraded (check the current
version first), and pay attention to our newest version NO;
2. Following the below steps to confirm your current version. Don’t need to
upgrade if the current version confirmed to be the newest version already;
3. Be sure you have connected the adapter to Camera and lens before
upgrading;
4. While in upgrading the 'MAC' Firmware, if it shows 'file damaged', please
enter into setting of 'safety and privacy' and choose 'Any source' option to
make your computer accept the file first;

[For Windows]
◆Check the Firmware Version
Notice: Be sure you have connected the adapter to Camera and Lens before
checking. The adapter performs as a lens then.
1. Press [Menu] ---- Enter into [Setting] ----- Choose [Version]
2. Camera will show the current Lens (ENF-E1 adapter) Version
If using QX Series Camera, one can check the version via executed upgrading
software.
◆Firmware upgrade preparation
Before download the upgrading files, prepare the following works excepting
the camera.

1. Operation Software
【Windows 】
Supported Software：Windows 10 / Windows 8.1 / Windows 8 / Windows 7
SP1 / Windows Vista*1 SP2
(Don’t support *1 Starter edition)
2. Other Software Requirement
Hard disk space: 200MB or More
Internal Storage: 512MB or More
Notice: Please turn off all the application programs before upgrading
3. Other Requirement
3.1 Power
Full charge of Battery NP-FW50
Note: One can operate only when the battery power is over than 3 grids, we
recommend the full-power battery.
3.2 Original USB Cable
Note: We don’t assure one can successfully upgrade with the USB cable
bought from the-third party manufacturer
◆Firmware Upgrade
--Please use the full-charged battery or battery adapter before upgrading;
--Please don’t take out the battery or interrupt the power during firmware
upgrading, otherwise it may cause your camera’s damage permanently;
--Please take out the memory card before upgrading
1. Download the upgrading file

Click to download the relevant files.
Save the downloaded file Update_ENF-E1v02(W).rar to your computer’s
desktop (Recommended)
Then after decompression
For the users of Windows 8,8.1 and Windows 10
According to the original settings of IE, the updated files will be saved in
‘Downloaded File’. Click ‘Desktop’ from Screen’s ‘START’ button, and find the
‘Downloaded File’ from ‘Via Browser’
2. Start Firmware Upgrade
Double-click the downloaded file Update_ENF-E1v02(W).exe
The firmware will start to upgrade
Picture 1
3. Check the USB Connection Mode
3.1 Turn on the Camera
3.2 Choose [Menu] ---- [Setting] ---- [USB Connection] , choose [Mass Storage]
While in using QX Series Camera, no need of this step

4. Connect Camera and Computer
--Take out the memory card before upgrade
4.1 Connect the camera, adapter and lens to your computer by USB cable
Notice: The LCD screen will shut down after connection, following the next
step to operate
4.2 Now, please confirm that it appears with sign at lower right corner of your
computer
4.3 Click [Next Step], the picture 2 will show on your computer’s screen
Picture 3 will show on your camera’s screen
Notice: Don’t interrupt the power of your camera from now until the upgrading
finished
Picture 2: Computer Shows

Picture 3: Camera LCD Shows
5. Confirm your need of Upgrade
5.1 Confirm the content of Picture 2 and Picture 3, click [Next Step]. The
current and updated firmware version will appear at lower left corner of your
screen (picture 4)
5.2 Confirm [Current Version], click [Next Step]
Notice: If it appears like Picture 5, there’s no need of your upgrading. Please
stop the USB connection and click [Finish] by prompt of upgrading. Turn off the
camera’s power, take out battery or battery adapter, restart your camera.
Picture 4 Need
Upgrading
Picture 5 No Need Upgrading

6. Start Upgrade
6.1 Start Date transferring
Progress-bar will appear while in transferring (About 5s)
Picture 6
Note: Don’t turn off your camera or stop USB connection during the data
transferring
6.2 Picture 7 will appear after finishing the data transferring, click
[Finish]
Picture 7

6.3 Start to upgrade the program (About 30s)
Picture 8
6.4 Upgrading Finished
While it appears with ‘Lens update complete’ on your camera’s screen, the
upgrading is finished
If using QX series, the upgrading is finished if your screen’s showing
disappear
Picture 9

Note: Dis-connect the USB connection and re-put battery to re-start the
camera after upgrading
7. Check the lens’ Firmware Version
Please operate by following instructions, check to make sure the firmware
version has been updated to Ver.02
Choose [Menu] --- [Setting] --- [Version]
[For Mac OS]
◆Check the Firmware Version
Notice: Be sure you have connected the adapter to Camera and Lens before
checking. The adapter performs as a lens then.

1. Press [Menu] ---- Enter into [Setting] ----- Choose [Version]
2. Camera will show the current Lens (ENF-E1 adapter) Version
If using QX Series Camera, one can check the version via executed upgrading
software.
◆Firmware upgrade preparation
Before download the upgrading files, prepare the following works excepting
the
camera.
1. Operation Software
【Mac OS】
Supported software: Mac OS X v.10.5–10.10
2. Other Software Requirement
CPU: Intel Processor
Not support Core Solo and Core Duo Processor
Hard Disk Space: 200MB or more
Internal Storage: 512MB or More
Make sure to turn off the other application routines before firmware upgrade