CommScope RUCKUS SmartZone 300 User manual

RUCKUS SmartZone 300
Spare Hard Disk Drive Quick
Setup Guide
This Quick Setup Guide provides basic instrucons for ordering
and installing a spare hard disk drive (HDD) into the Ruckus
SmartZone 300 (SZ300) controller.
For informaon on advanced conguraon and management
opons, see the Geng Started Guide and other appropriate
documents, which are available for download from the Ruckus
Support website:
hps://support.ruckuswireless.com/documents.
This Guide in Other Languages
请从以下网站获得该指南的简体中文版 hps://
support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse
suivante hps://support.ruckuswireless.com.
このガイドの日本語版は hps://support.ruckuswireless.com
でご覧ください。
이 가이드의 한국어 버전은 웹 사이트 (hps://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
Veja a versão em português (Brasil) deste guia em hps://
support.ruckuswireless.com.
Puede ver la versión en español (América Lana) de esta guía en
hps://support.ruckuswireless.com.
Hard Disk Drive Ordering Informaon
To order a spare hard disk drive for the SmartZone 300 controller,
contact Ruckus Support.
For informaon on how to contact Ruckus Support, visit hps://
support.ruckuswireless.com/contact-us. When asked for the part
number, provide the informaon in the following table.
Part Number Descripon
902-S350-0000 Kit, Spare (FRU), hard disk drive, SZ300
Opening the Front Bezel
The front bezel helps prevent accidental access to the controller's
modules. Before you can install a module, you must open the
front bezel.
NOTE: If the controller is mounted in a rack with adjacent units
below the unit where a module needs to be serviced, Ruckus
recommends extracng the controller from the rack
approximately 5cm (2 in.). This will provide clearance of the
bezel when rotated out towards you.
Follow these steps to open the front bezel.
1. With the controller in front of you, place your ngers on both
sides of the front bezel.
2. Pull the bezel toward you unl it opens.
3. Gently lower the bezel to expose the controller's replaceable
modules.
FIGURE 1 Controller with the front bezel open
Installing a Spare Hard Disk Drive
Aer you have obtained a spare hard disk drive and opened the
front bezel of the SmartZone 300 controller, you are ready to
install the drive.
NOTE: Both hard disk drives (HDDs) are redundant and hot-
swappable. You do not need to power o the controller to
swap a single failed HDD.
Follow these steps to install the hard disk drive.
1. On the front panel, idenfy the HDD that you want to
replace. From the top of the front panel, disk tray 1 is for a
solid state drive (SSD), and disk trays 2 and 3 are for HDDs
(see the following gure).
NOTE: Tray 4 is unused.
FIGURE 2 Disk trays on the front panel of the controller
NOTE: If you are replacing a failed disk, check the LED of
each tray. A red or amber LED indicates that the disk is not
operaonal.
2. Unlock the disk tray by moving the orange disk tray lock to
the le (unlock) posion.
3. Press the black/blue tray buon to open the tray handle.
4. Hold the tray handle, and rmly pull it toward you unl the
disk tray, along with the HDD, comes out of the chassis
completely. Put the disk tray assembly aside.
5. Unpack the replacement HDD. The replacement HDD comes
assembled with its own disk tray.
6. Insert the disk tray (with the replacement HDD) into the disk
bay unl the drive locks in the connector on the SAS
backplane.
7. Close the handle, and lock the tray by moving the orange disk
tray lock to the right (lock) posion.
8. Verify that the new drive's status LED ashes green. This
indicates that the controller is rebuilding the RAID array.
When the controller completes rebuilding the RAID array, the
drive's status LED shows solid green.
You have completed replacing a spare HDD in the SmartZone 300
controller.
Copyright © 2021 CommScope, Inc. All rights reserved. Page 1 of 2
Published December 2021, Part Number 800-72227-001 Rev E

Closing the Front Bezel
Aer you complete installing a module, remember to close the
front bezel to prevent access to the modules and protect them
from dust and dirt.
If the controller is mounted in a rack, before compleng the
following steps, grab the side handles on the controller, and push
the controller back into the rack. Secure the controller to the rack
using the rack fasteners.
Perform the following steps to close the front bezel.
1. With the controller in front of you, gently li the bezel and
push it back onto the front panel of the controller.
2. Gently press the bezel against the front panel unl it clicks
into place.
The bezel should now be ush against the front panel,
completely covering it.
© 2021 CommScope, Inc. All rights reserved.
ARRIS, the ARRIS logo, COMMSCOPE, RUCKUS, RUCKUS WIRELESS, the Ruckus
logo, and the Big Dog design are trademarks of CommScope, Inc. and/or its
aliates. Wi-Fi Alliance, Wi-Fi, the Wi-Fi logo, Wi-Fi Cered, the Wi-Fi
CERTIFIED logo, Wi-Fi Protected Access, the Wi-Fi Protected Setup logo, Wi-Fi
Protected Setup, Wi-Fi Mulmedia and WPA2 and WMM are trademarks or
registered trademarks of Wi-Fi Alliance. All other trademarks are the property of
their respecve owners.
Copyright © 2021 CommScope, Inc. All rights reserved. Page 2 of 2
Published December 2021, Part Number 800-72227-001 Rev E