CompuLab SB-A510 User manual

SB-A510
Reference Guide
All manuals and user guides at all-guides.com
all-guides.com

Revised May 2011 SB-A510 Rev 1.1 2
© 2010 CompuLab
All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval
system, or transmitted, in any form or by any means whether, electronic, mechanical, or otherwise
without the prior written permission of CompuLab.
No warranty of accuracy is given concerning the contents of the information contained in this
publication. To the extent permitted by law no liability (including liability to any person by reason of
negligence) will be accepted by CompuLab, its subsidiaries or employees for any direct or indirect
loss or damage caused by omissions from or inaccuracies in this document.
CompuLab reserves the right to change details in this publication without notice.
Product and company names herein may be the trademarks of their respective owners.
CompuLab
P.O. Box 66 Nesher
36770 ISRAEL
Tel: [phone]
http://www.compulab.co.il
Fax: [phone]
All manuals and user guides at all-guides.com

Table of Contents
Revised May 2011 SB-A510 Rev 1.1 3
Table of Contents
1INTRODUCTION ..............................................................................................................6
1.1 About This Document...................................................................................................... 6
1.2 Related Documents .......................................................................................................... 6
2OVERVIEW........................................................................................................................7
2.1 Highlights......................................................................................................................... 7
2.2 Block Diagram................................................................................................................. 8
2.3 Features ............................................................................................................................ 9
3SYSTEM COMPONENTS ..............................................................................................11
3.1 DC Power Supply........................................................................................................... 11
3.2 DVI Transmitter............................................................................................................. 12
3.3 LVDS Transmitter.......................................................................................................... 12
3.4 PCI-E to PCI Bridge ......................................................................................................12
3.5 Back-Up Battery............................................................................................................. 13
4INTERFACES AND CONNECTORS............................................................................14
4.1 CM-A510 Interface Connectors (P1, P2)....................................................................... 14
4.2 DC Power Jack (J2)........................................................................................................ 14
4.3 RS232 connector (P10).................................................................................................. 14
4.4 USB Host Connectors (P11, P15).................................................................................. 15
4.5 Gigabit Ethernet Connectors (P11, P15)........................................................................ 15
4.6 Analog VGA connector (P7).......................................................................................... 16
4.7 DVI Connector (J4)........................................................................................................17
4.8 LCD FPC (P13)..............................................................................................................18
4.9 LVDS Header (P9)......................................................................................................... 19
4.10 Touch Screen Header (P12).......................................................................................19
4.11 Power Output Terminals (P17, P19) ......................................................................... 20
4.12 S-ATA Connector (P18)............................................................................................20
4.13 S/PDIF Connectors (P22, U6)...................................................................................21
4.14 CompuLab Video Input FPC (P25)........................................................................... 22
4.15 MMC/SD/SDIO Socket (P5)..................................................................................... 23
4.16 Audio Jacks (J1, J3)................................................................................................... 23
4.17 MISC. Signals Headers (P14, P21) ........................................................................... 24
4.18 JTAG Header (P16)................................................................................................... 24
4.19 Boot Source Button (SW1)........................................................................................25
4.20 Reset Button (SW2)...................................................................................................25
4.21 Suspend/Resume Button (SW3)................................................................................25
4.22 Jumpers...................................................................................................................... 26
4.23 LEDs.......................................................................................................................... 26
All manuals and user guides at all-guides.com

Table of Contents
Revised May 2011 SB-A510 Rev 1.1 4
5MECHANICAL DRAWINGS.........................................................................................27
6OPERATIONAL CHARACTERISTICS.......................................................................29
6.1 Absolute Maximum Ratings .......................................................................................... 29
6.2 Recommended Operating Conditions............................................................................ 29
6.3 DC Electrical Characteristics......................................................................................... 29
6.4 Power Consumption....................................................................................................... 29
6.5 Operating Temperature Ranges......................................................................................30
7ACCESSORIES................................................................................................................31
All manuals and user guides at all-guides.com

Revised May 2011 SB-A510 Rev 1.1 5
Table 1 Document Revision Notes
Date
Description
November 2010
First release
May 2011
Fixed table 4, Jumper E8 description fixed.
Please check for a newer revision of this manual at CompuLab's web site –http://www.compulab.co.il/.
Compare the revision notes of the updated manual from the web site to those of the printed or
electronic version you have.
All manuals and user guides at all-guides.com

Revised May 2011 SB-A510 Rev 1.1 6
1 INTRODUCTION
1.1 About This Document
This document is part of a set of reference documents providing information necessary to operate and
program CompuLab’s SBC-A510.
1.2 Related Documents
For additional information not covered in this manual, please refer to the documents listed in Table 2.
Table 2 Related Documents
Document
Location
CM-A510 Product Developer Resources
http://www.compulab.co.il/
All manuals and user guides at all-guides.com
all-guides.com

Revised May 2011 SB-A510 Rev 1.1 7
2 OVERVIEW
2.1 Highlights
Single board computer implemented
by the combination of a CM-A510
module and a SB-A510 baseboard.
Micro-ATX form factor.
Marvell Armada 510 SoC @1000MHz
1GB DDR3
512MB NAND flash
VMeta video decode sub-system
@500MHz with H.264, MPEG-4 and
MPEG-2 support
Integrated GPU with 2D/3D graphics
acceleration and OpenGL-ES support
WLAN / WiFi 802.11b/g/n interface
1920 x 1080 graphics controller with
interfaces for LVDS, RGB, DVI and
VGA monitors
2 x 1000 BaseT Ethernet ports
SATA hard-drive interface
4 x USB2 high-speed host ports
PCI Express and PCI extension
interfaces
MMC / SD / SDIO socket
Sound codec with stereo output, line
input and S/PDIF output support
Touch-screen interface
Serial ports, GPIO’s
7V - 17V DC power supply, 3 - 8 watt
RTC with lithium back-up battery
The SBC-A510 is a micro-ATX compliant,
single board computer. It is implemented
with a CM-A510 module providing most of
the functions, and a SB-A510 carrier board
providing standard connectors and
additional peripherals. The rich feature set
of the SBC-A510 is customizable according
to the price / performance targets of the
user's application.
The SBC-A510 features expansion
connectors, opening it to a wide range of
standard peripheral cards. Its wide input
range switched power supply is compatible
with the requirements of telecom and
automotive applications.
All manuals and user guides at all-guides.com

Revised May 2011 SB-A510 Rev 1.1 8
2.2 Block Diagram
Figure 1 SB-A510 Block Diagram
NAND
DDR3
Sheeva
ARM v7
Display
controller
MM C /SD-0
1000M b
Ethernet
Audio
Codec
CM -A510
analog VGA
Stereo in
Stereo out
2D / 3D
graphics
accelerator
Vm eta
Video
Decoder
SA TA 2.0
controller
PCI
Express
controller
PCIe-0
24bitRGB
I2C-2
S/PD IF
WiFi b/g/n
COM-C
Cam era
COM-B
I2C-1
SPI Flash
Touch
Screen
controller
GPIO
Pow er
Managem ent
1000M b
Ethernet
USB 2 x4
RTC
COM-A
DC
pow er
supply
5V DC
coin cell battery back-up
DC
conn.
DB-15
audio
jack
audio
jack
SATA
conn.
RJ-45
RJ-45
100-m il
header
mini serial
conn.
SD socket
dual-U S B
dual-U S B
PCIe
mux
PCIe to PCI
bridge
PCIe slot
PC I slot
PCIe
PCI
40-pin FPC
HDMI
conn. R G B to D VI converter
RGB to LVDS
converter
100-m il
header
Com pulab video
input FPC
I2C
12V-DC OPTIC
conn. C OAX conn.
All manuals and user guides at all-guides.com

Revised May 2011 SB-A510 Rev 1.1 9
2.3 Features
SB-A510 does not have assembly options. The "CM Option" column specifies the P/N code of CM-
A510 required to have the particular feature.
"+" means that the feature is always available, regardless of P/N code.
Table 3 SB-A510 Features
Feature
Specifications
CM-A510
Option
CPU
SDRAM
Flash Disk
2D / 3D graphics
Video acceleration
See Feature List of the relevant CoM
COM-A
Partial modem controls, RS-232, ultra mini serial conn.
+
COM-B
Rx/Tx only, 3.3V levels, 100-mil header
+
COM-C
Partial modem controls, 3.3V levels, 100-mil header
+
Gigabit Ethernet
One or two CM-A510 1000 BaseT Ethernet ports.
RJ-45 connectors and activity LED's.
Ex
Hard disk
SATA-II interface, standard SATA connector
+
LCD Panel
TFT panel support. 40-pos FPC connector for direct interface to
certain TFT panels
+
VGA
Analog VGA interface. DB-15 connector
+
DVI
DVI monitor support, HDMI connector
+
LVDS
4 pair LVDS panel interface, 100-mil header
+
USB 2.0 host
Two USB 2.0 host ports, 480 Mbps, type-A connectors
U2
Additional two USB 2.0 high speed port, 480 Mbps, type-A
connectors
U4
PCI Express
Mini PCI Express x1 slot
+
PCI
Single PCI slot, configurable 3.3V or 5V voltage level
Note: only one extension slot is functional at a time: PCI or PCI
Express
+
WiFi
WiFi interface, including on-board antenna connector, provided on
CM-A510
W
MMC / SD / SDIO
MMC / SD / SDIO support (including SDHC up to 32GB).
Standard full-size SD socket.
+
Camera
Direct camera sensor support. 40-pos FPC connector.
+
GPIO
12 lines, 100-mil header.
+
Touch Panel
TSC2046 touch-screen controller. Interface to LCD panel.
I
Sound I/O
I2S compliant audio codec, line input and speakers (stereo) jacks
A
RTC Battery
Real time clock on CM-A510, supplied by back-up lithium battery
on SB-A510
+
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 10
Table 4 Electrical, Mechanical and Environmental Specifications
Supply Voltage
High efficiency switched power supply.
Unregulated 7.5 to 17 volt input
Power consumption
3W to 8W in full activity, depending on CPU speed and selected features
Dimensions
170 mm (L) x 170 mm (W) x 35 mm (H)
Weight
200 gram
Operation temperature
(case)
Commercial: 0o to 70o C
Extended: -20o to 70o C
Industrial: -40o to 85o C
Storage temperature
-40o to 85o C
Relative humidity
10% to 90% (operation)
05% to 95% (storage)
Shock
50G / 20 ms
Vibration
20G / 0 - 600 Hz
MTBF
> 100,000 hours
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 11
3 SYSTEM COMPONENTS
3.1 DC Power Supply
All SB-A510 power rails are generated from a 12V DC input (connector J2).
SB-A510 supports two power states:
Full power mode –all SB-A510 power rails are enabled.
Low power mode –only power rails required for sleep-mode support are enabled. All other
voltage rails are disabled (gated).
SB-A510 power state is controlled by the CM-A510 “STBY_PWRDWN” signal, available on pin 37
of connector P1.
Table 5 Power mode selector signal table
STBY_PWRDWN
SB-A510 power mode
High
Full power mode
Low
Low power mode
The figure below describes the SB-A510 power scheme.
Figure 2 SB-A510 Power Scheme
Gate - closed when in low power mode
Power rail - always available
Power rail - Available only when system
is in full power mode
Software controlled gate
Power supply regulator
DC 12V
input
Step-Down
(12V -> 5V)
Step Down
(12V -> 3.3V)
Gate
Gate SW
Gate
5VSBY
3V3SBY VCC3_3 VCC_MMC
LDO
(3.3V -> 1.8V)
LDO
(3.3V -> 1.5V)
LDO
(3.3V -> 1.0V)
Gate
Gate
VCC_5V
1.5SBYVCC1_5
1.0SBYVCC1_0
VCC1_8
Gate VCC_12V
LEGEND
The “5VSBY” power rail supplies the CM-A510 module and certain SB-A510 peripherals. Other
power rails are used only for SB-A510 peripherals.
All manuals and user guides at all-guides.com
all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 12
3.2 DVI Transmitter
The SB-A510 is equipped with a DVI Transmitter that is based on the TFP410/SIL164 IC. DVI
output signals are routed to the onboard HDMI Connector (J4). The DVI Transmitter is connected to
the 24bit RGB interface of the CM-A510.
TFP410/SIL164 is fully DVI 1.0 compliant. The DVI Transmitter on the SB-A510 is configured for
rising edge data sampling, single ended pixel clock and standard 3.3V CMOS input signal levels. The
transmitter can be shut down by software (GPIO03 on I2C GPIO extender IC) and can also inform
the system (through GPIO02 on I2C GPIO extender IC) whether a monitor is connected to the
transmitter output.
In order to use the DVI interface, the CM-A510 display system has to be configured properly for
RGB888 operation mode.
3.3 LVDS Transmitter
The SB-A510 is equipped with an LVDS Transmitter that is based on the DS90C365A IC. LVDS
output signals are routed to a 100mil header (P20). The LVDS Transmitter is connected to the display
interface of the CM-A510.
The DS90C365A is a National Semiconductor +3.3V Programmable 18-bit Flat Panel Display link-
87.5MHz LVDS Transmitter. The transmitter is fully compatible with the TIA/EIA-644 LVDS
standard and supports VGA, SVGA and XGA display modes.
The LVDS Transmitter is configured for rising edge data sampling. GPIO04 on the I2C GPIO
extender, can be used to put the transmitter into shutdown mode.
In order to use the LVDS interface, the CM-A510 display system has to be configured properly for
RGB888 operation mode.
3.4 PCI-E to PCI Bridge
SB-A510 PCI interface is implemented with a Pericom PI7C9X111 IC connected to the CM-A510
PCI-E link. The interface supports the following features:
Compliant with PCI Local Bus Specification, Revision 3.0
Compliant with PCI-to-PCI Bridge Architecture Specification, Revision 1.2
Compliant with PCI Bus PM Interface Specification, Revision 1.1
Transparent mode support
Compliant with Advanced Configuration and Power Interface Specification (ACPI), Revision
2.0b
NOTE: In order to use the PCI interface, PI7C9X111 and PCI-E link must be set to the correct
operating mode with jumpers E2, E3, and E4. Please refer to chapter 4.22 for
additional details.
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 13
3.5 Back-Up Battery
SB-A510 is supplied with a 3V 200mAh Lithium Dioxide coin cell, which powers the CM-A510
RTC whenever the main power supply is not present.
NOTE: The E5 jumper must be installed for RTC back-up support. Please refer to chapter 4.22
for additional details.
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 14
4 INTERFACES AND CONNECTORS
4.1 CM-A510 Interface Connectors (P1, P2)
The CM-A510 CoM is interfaced through two 0.6mm pitch, 140pin connectors - P1 and P2.
Please refer to the “CM-A510 reference guide” for signal descriptions.
Table 6 P1 and P2 connector data
Manufacturer
P/N of SB-A510 Connector
P/N of CM-A510 Connector
(Mating)
AMP
1-5353183-0
1-5353190-0 or CON140
4.2 DC Power Jack (J2)
Main power input connector of the SB-A510.
Table 7 12V DC input jack pinout
Pin
Signal Name
1
GND
2
GND
3
VIN12V
Table 8 J2 connector data
Manufacturer
Mfg. P/N
Astron
15-02037-R
Mating with power supply adapter 209C10020 supplied by CompuLab.
4.3 RS232 connector (P10)
The RS232 port of the CM-A510 is routed to the SB-A510 on-board RS232 ultra-mini connector
(P10). All signals are at RS232 levels.
Table 9 P10 connector pinout
Pin
Signal Name
Pin
Signal Name
1
RS232_TXD
5
NC
2
RS232_RTS
6
NC
3
RS232_RXD
7
NC
4
RS232_CTS
8
GND
Table 10 P10 connector data
Manufacturer
Mfg. P/N
Mating connector
Wieson
G3169-500001
Wieson, P/N: 4306-5000
The connector is compatible with the CABDB9UMP cable supplied by CompuLab.
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 15
4.4 USB Host Connectors (P11, P15)
The four USB2.0 host ports provided by the CM-A510 are available through two dual type-A USB
connectors (P11 & P15).
For USB ports 1, 2 and 3, the CM-A510 provides the “VBUS enable” signal and monitors the
“VBUS good” signal generated on SB-A510. USB port 0 power is controlled by GPIO00, and
monitored by GPIO01, on the I2C GPIO extender onboard the SB-A510.
NOTE: The actual number of USB2.0 ports available depends on the CM-A510 USB
configuration option.
Table 11 P11 connector pinout (USB)
USB port 0 (Bottom)
USB port 1 (Middle)
Pin
Signal Name
Pin
Signal Name
B1
VCC_USB0
B5
VCC_USB1
B2
USBN0
B6
USBN1
B3
USBP0
B7
USBP1
B4
GND
B8
GND
Table 12 P15 connector pinout (USB)
USB port 2 (Bottom)
USB port 1 (Middle)
Pin
Signal Name
Pin
Signal Name
B1
VCC_USB2
B1
VCC_USB3
B2
USBN2
B2
USBN3
B3
USBP2
B3
USBP3
B4
GND
B4
GND
Table 13 P15/P11 connector data
Manufacturer
Mfg. P/N
Mating connector
YDS
F-10202GDD2
Standard USB type A plug
4.5 Gigabit Ethernet Connectors (P11, P15)
The SB-A510 is equipped with two Gigabit Ethernet RJ45 connectors (P11 & P15). P11 is interfaced
with the CM-A510 LAN0 port, and P15 with the LAN1 port.
Table 14 P11 connector pinout (Ethernet)
Pin
Signal Name
Pin
Signal Name
E1
LAN0_CT1
E10
LAN0_CT2
E2
LAN0_MDIP0
E11
VCC3_3
E3
LAN0_MDIN0
E12
LAN0_ACT
E4
LAN0_MDIP1
E13
LAN0_LINK
E5
LAN0_MDIN1
E14
VCC3_3
E6
LAN0_MDIP2
E15
GND
E7
LAN0_MDIN2
E16
GND
E8
LAN0_MDIP3
E17
GND
E9
LAN0_MDIN3
E18
GND
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 16
Table 15 P15 connector pinout (Ethernet)
Pin
Signal Name
Pin
Signal Name
E1
LAN1_CT1
E10
LAN1_CT2
E2
LAN1_MDIP0
E11
VCC3_3
E3
LAN1_MDIN0
E12
LAN1_ACT_T
E4
LAN1_MDIP1
E13
LAN1_LINK
E5
LAN1_MDIN1
E14
VCC3_3
E6
LAN1_MDIP2
E15
GND
E7
LAN1_MDIN2
E16
GND
E8
LAN1_MDIP3
E17
GND
E9
LAN1_MDIN3
E18
GND
Table 16 P15/P11 connector data
Manufacturer
Mfg. P/N
Mating connector
YDS
F-10202GDD2
Standard Ethernet RJ45 plug
NOTE: The actual number of Gigabit Ethernet ports available depends on the CM-A510
Ethernet configuration option.
4.6 Analog VGA connector (P7)
The SB-A510 is equipped with an analog VGA output connector (P7). P7 is connected to the CM-
A510 analog VGA output, and provides a standard VGA DB-15 interface for PC monitors.
The DSUB_I2C2_SCL and DSUB_I2C2_SDA signals are routed to the CM-A510 I2C port 2 signals
and serve as a DDC host interface.
Table 17 P7 connector pinout
Pin
Signal Name
Pin
Signal Name
1
VGA_R
10
GND
2
VGA_G
11
NC
3
VGA_B
12
DSUB_I2C2_SDA
4
NC
13
VGA_HSYNC
5
GND
14
VGA_VSYNC
6
GND
15
DSUB_I2C2_SCL
7
GND
16
GND
8
GND
17
GND
9
VCC_5V
Table 18 P7 connector data
Manufacturer
Mfg. P/N
Mating connector
Astron
HD6A-15-PFHN1T-R
Standard VGA monitor plug
All manuals and user guides at all-guides.com
all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 17
4.7 DVI Connector (J4)
The SB-A510 is equipped with a standard HDMI socket (J4) providing a DVI interface. The on-board
DVI transmitter IC drives the DVI signals through the HDMI socket. For additional details, please
refer to section 3.2 of this document.
The DVI_DDCSCL and DVI_DDCDAT signals are routed to the CM-A510 I2C port 0 signals, and
provide DVI DDC interface.
In order to use the DVI interface, the CM-A510 display system must be set to RGB 888 operation
mode.
Table 19 J4 connector pinout
Pin
Signal Name
Pin
Signal Name
1
DVI_TXD2+
12
DVI_TXC-
2
GND
13
GND
3
DVI_TXD_2-
14
NC
4
DVI_TXD1+
15
DVI_DDCSCL
5
GND
16
DVI_DDCDAT
6
DVI_TXD1-
17
GND
7
DVI_TXD0+
18
DVI_5V
8
GND
19
HTPLG
9
DVI_TXD0-
20
GND
10
DVI_TXC+
21
GND
11
GND
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 18
4.8 LCD FPC (P13)
The on-board LCD FPC connector (P13) allows easy integration with custom LCD panels. The
CABFPC40 and CONLCD-GEN accessories (supplied by CompuLab) provide a generic 100-mil
header connection. For additional details, please refer to section 7of this document.
In order to use the P13 connector, set the CM-A510 display mode to RGB 888.
NOTE: The P13 connector does not provide power for the LCD backlight. An external power
source is required.
Table 20 P13 connector pinout
Pin
Signal Name
Pin
Signal Name
1
TS_X-
21
VCC3_3
2
LCD_PWR_SRC
22
TS_Y+
3
GND
23
TS_Y-
4
LCDnRST
24
GND
5
LCD_D3_T
25
TS_X+
6
VCC3_3
26
LCD_D18_T
7
LCD_D4_T
27
VCC3_3
8
LCD_D5_T
28
LCD_D19_T
9
GND
29
LCD_D20_T
10
LCD_D6_T
30
GND
11
LCD_D7_T
31
LCD_D21_T
12
VCC3_3
32
LCD_D22_T
13
LCD_D15_T
33
GND
14
LCD_D14_T
34
LCD_D23_T
15
GND
35
LCD_DE_T
16
LCD_D13_T
36
VCC3_3
17
LCD_D12_T
37
LCD_HSYNC_T
18
VCC3_3
38
LCD_VSYNC_T
19
LCD_D11_T
39
GND
20
LCD_D10_T
40
LCD_PCLK_T2
Table 21 P13 connector data
Manufacturer
Mfg. P/N
Mating connector
CVILux
CF20-401D0R0
FFC, 40 cont, 0.5mm
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 19
4.9 LVDS Header (P9)
LVDS output signals are routed from the LVDS Transmitter IC to the onboard 100mil header (P9).
For additional details, please refer to section 3.3 of this document.
In order to use the LVDS interface, CM-A510 display system must be set to RGB 888 operation
mode.
NOTE: The P9 connector does not provide power for the LVDS LCD panel and its backlight.
An external power source is required.
Table 22 P9 connector pinout
Pin
Signal Name
Pin
Signal Name
1
LVDS_NE0
6
GND
2
LVDS_NE1
7
LVDS_NE2
3
LVDS_PE0
8
LVDS_NEC
4
LVDS_PE1
9
LVDS_PE2
5
GND
10
LVDS_PEC
4.10 Touch Screen Header (P12)
The touch screen (P12) header of the SB-A510 allows evaluating any resistive touch panel with the
touch panel interface provided by the CM-A510. Please refer to the CM-A510 reference guide for
additional details on the touch-screen interface.
NOTE: The P12 connector does not provide power to the touch panel.
Table 23 P12 connector pinout
Pin
Signal Name
Pin
Signal Name
1
GND
6
NC
2
TS_X-
7
TS_Y+
3
GND
8
TS_Y-
4
TS_X+
9
GND
5
NC
10
GND
All manuals and user guides at all-guides.com

Interfaces and Connectors
Revised May 2011 SB-A510 Rev 1.1 20
4.11 Power Output Terminals (P17, P19)
The SB-A510 is equipped with two power output terminals. The power output terminals (P17 & P19)
are provided for the S-ATA hard drive power supply.
Table 24 P17 connector pinout
Pin
Signal Name
1
VCC_12V
2
GND
Table 25 P19 connector pinout
Pin
Signal Name
1
VCC_5V
2
GND
4.12 S-ATA Connector (P18)
The SB-A510 is equipped with a standard S-ATA Connector (P18) that allows interfacing CM-A510
with standard and S-ATA disk drives.
Table 26 P18 connector pinout
Pin
Signal Name
1
GND
2
SATA_TX+
3
SATA_TX-
4
GND
5
SATA_RX-
6
SATA_RX+
7
GND
Table 27 P13 connector data
Manufacturer
Mfg. P/N
Mating connector
AMP
-
Standard S-ATA Cable.
All manuals and user guides at all-guides.com