Boser HS-6301 User manual

HS-6301
Dual PIII / Dual LAN / VGA / SCSI
•Dual CPU•Dual LAN•CRT/Panel•133MHz FSB•
•SCSI•DMA33•WDT•PC/104•USB•
•DOC•IrDA•Hardware Monitor•
•PICMG Bus Industrial Single Board Computer•
HS-6301LLV
Dual PIII / Dual LAN / VGA
•Dual CPU•Dual LAN•CRT/Panel•133MHz FSB•
•DMA33•WDT•PC/104•USB•
•DOC•IrDA•Hardware Monitor•
•PICMG Bus Industrial Single Board Computer•

Copyrights
This manual is copyrighted and all rights are reserved. Unauthorized translation
orreproductiontoanyelectronicorreadableforminwholeorin part without prior
written consent from the manufacturer is prohibited.
In general, the manufacturer will not be liable for any direct, indirect, special,
incidental or consequential damages arising from the use of the product or
documentation, even if advised of the possibility of such damages.
The manufacturer reserves the right to change the contents of this manual
without prior notice. The author assumes no responsibility for any errors or
omissions,whichmayappearinthismanual,nordoesitmakea commitment to
update the information contained herein.
Trademarks
BOSER is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
ISB is a registered trademark of BOSER Technology Co., Ltd.
All other trademarks, products and or product's name mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2001
All Rights Reserved.
User Manual edition 1.2, Aug.24 2001

3
Contents
HS-6301.......................................................................................I
HS-6301LLV ................................................................................II
GENERAL INFORMATION.................................................................. 5
1.1 MAJOR FEATURES ....................................................................... 6
1.2 SPECIFICATIONS........................................................................... 7
1.3 DELIVERY PACKAGE.................................................................... 9
HARDWARE INSTALLATION.............................................................10
2.1 CAUTION OF STATIC ELECTRICITY...................................................10
2.2 CAUTION ON UNPACKING AND BEFORE INSTALLATION .........................11
2.3 HS-6301'S LAYOUT....................................................................12
2.4 QUICK LISTING OF JUMPERS...........................................................13
2.5 QUICK LISTING OF CONNECTORS.....................................................14
2.6 JUMPER SETTING DESCRIPTION.......................................................15
2.7 SETTING CPU'S HOST CLOCK .......................................................16
2.8 DISKONCHIPTM ADDRESS SETTING..................................................16
2.9 WATCH-DOG TIMER.....................................................................17
2.10 USB PORTS CONNECTOR............................................................19
2.11 SETTING THE RTC CONFIGURATION................................................19
2.12 SYSTEM MEMORY DRAM............................................................19
CONNECTION...................................................................................20
3.1 POWER CONNECTOR ...................................................................20
3.2 IDE'S LED, KEYLOCK AND RESET BUTTON......................................21
3.3 PCI E-IDE DRIVE CONNECTOR......................................................22
3.4 PARALLEL PORT CONNECTOR.......................................................23
3.5 THE FLOPPY DISK DRIVE CONNECTOR .............................................24
3.6 SERIAL PORTS...........................................................................25
3.7 KEYBOARD & MOUSE CONNECTOR.................................................26
3.8 VGA CONNECTORS ....................................................................27
3.9 IR CONNECTOR..........................................................................30
3.10 FAST ETHERNET CONNECTOR......................................................30
3.11 ULTRA III SCSI INTERFACE CONNECTOR........................................32
3.12 HARDWARE MONITOR................................................................33

4
3.13 PC/104 BUS CONNECTION..........................................................33
AWARD BIOS SETUP .......................................................................35
4.1 MAIN MENU...............................................................................36
4.2 STANDARD CMOS SETUP............................................................37
4.3 BIOS FEATURES SETUP...............................................................38
4.4 CHIPSET FEATURES SETUP............................................................39
4.5 INTEGRATED PERIPHERALS............................................................40
4.6 POWER MANAGEMENT SETUP........................................................41
SOFTWARE UTILITIES .....................................................................42
5.1 VGA INSTALL FOR WIN98 & NT4.0.................................................43
5.2 LAN INSTALL FOR WIN 98 & NT4.0................................................46
5.3 SCSI INSTALL FOR WIN98 & WIN2000.............................................49
5.4 SCSI INSTALL FOR NT4.0..............................................................57

5
Chapter-1
General Information
The HS-6301 is a Dual FC-PGA PICMG Bus Industrial Single Board Computer
with combined features to make it an ideal all-in-one Industrial Single Board
Computer, equipped with enhanced I/O effects, CRT/Panel interface and Dual
Intel®82559 100 Based LAN.
With on board DMA33 of mode 4 to IDE drive interface architecture, the HS-6301
supports33MB/secdatatransferratesanduptofour IDE disk drive connections.
The advanced PICMG Bus add-on connection of the HS-6301 allows users to
easilyusebothISA’s16bitandPCI’s32bitfullsetsignals.TheHS-6301 provides
four DIMM sockets that support up to 1GB of main system memory.
A single Flash chip holds the system BIOS, and you can change the Flash BIOS
using Utility Update. Advanced USB and IR ports also provide faster data
transmissions.The DOS version of the DiskOnChipTM socket can also be used
by issuing commands from the DOS prompt without the necessity of other
software. DiskOnChip supports up to 144MB.
In case a program stops unexpectedly, the on board Watch-Dog Timer will
automatically reset the CPU or generate an interrupt. The Watch-Dog Timer is
designed with hardware and doesn’t need any arithmetical functions of a
real-time clock chip. This ensures the reliability in an unmanned or standalone
system.

6
1.1 Major Features
?? Dual Socket 370 for Intel®CeleronTM / CoppermineTM 266~933MHz CPU
?? 100MHz system clock provides up to 133MHz
?? Four DIMM sockets provides up to 1GB
?? Fast PCI DMA33 controller supports four IDE disk drives
?? Two RS-232 serial ports include 16C550 UART with 16byte FIFO
?? One enhanced bi-directional parallel port supports SPP/EPP/ECP
?? On board PS/2 Keyboard and PS/2 Mouse connector
?? On board Winbond W83977 super I/O chipset
?? On board 8MB SMI 721 CRT/Panel display controller
?? On board Dual Intel®82559 100 Based LAN
?? On board Symbios 53C1000 Ultra III SCSI
?? On board PCI Bridge
?? PC/104 Bus connector
?? DiskOnChipTM memory size up to 144MB
?? TV Out Function support
?? ATX Power Function support
?? Hardware Monitor support

7
1.2 Specifications
?? CPU：Dual Socket 370 for Intel®CeleronTM/CoppermineTM
266~933MHz CPU
?? Bus Interface：PICMG Bus
?? Bus Clock Rate：100MHz system clock provides up to 133MHz
?? Memory：Four DIMM sockets provides up to 1GB
?? Chipset：Intel®82443 BX
?? I/O Chipset：Winbond®W83977
?? PCI Bridge：HINT®or equivalent device
?? VGA：SMI 721 with 8MB memory support CRT/Panel display up to
1280x1024, 64Kcolors
?? IDE：Four IDE disk drives support DMA33 transfer rate up to 33MB/sec
?? Floppy：Support to two floppy disk drives
?? Parallel Port：Supports SPP/ECP/EPP
?? Dual LAN：Dual Intel®82559 100 Based LAN
?? SCSI：Symbios 53C1000 Ultra III SCSI single channel SCSI control
speed up to 160MB/sec
?? Serial Port：Two RS-232 serial ports include 16C550 UART with
16byte FIFO
?? PC/104：PC/104 connector for 16bit ISA Bus
?? IR：One IrDA TX/RX header
?? USB：Support two USB ports
?? TV Out：Support PAL or NTSC system
?? Keyboard：PS/2 6pin Mini Din or 5pin connector
?? Mouse：PS/2 6pin Mini Din or 4pin header
?? DiskOnChipTM：Socket for DiskOnChipTM and memory size up to
144MB
?? BIOS：Award Y2K PnP Flash BIOS
?? Watch-Dog Timer：Set 1, 2, 10, 20, 110, 220 seconds activity trigger
with Reset or NMI
?? CMOS：DS12C887 or equivalent device
?? DMA Channels：7

8
?? Interrupt Levels：15
?? Fuse：Automatically resumes poly switch resetable fuse
?? Extra Power：One ATX Power input connector
?? Power Voltage：+5V, +12V, -12V
?? Maximum Power Consumption：+5V@14A(850MHz x 2),
+12V@220mA, -12V@20mA
?? Operating Temperature：0~60℃
?? Hardware Monitor：Winbond W83783S
?? Board Size：13.26”(L) x 4.8”(W)

9
1.3 Delivery Package
The Delivery package of HS-6301/HS-6301LLV includes all following
items：
?? HS-6301/HS-6301LLV Industrial Single Board
?? One Printer Flat Cable
?? One COM Port Flat Cable
?? Two IDE Flat Cable
?? FDD Flat Cable
?? Utility CD-ROM
?? User’s Manual
?? SCSI Flat Cable (HS-6301 only)
Please contact your dealer if any of the items is missing or damaged upon
purchase. Keep all parts of the delivery package with packing materials in
case of shipping or storing the product.

10
Chapter-2
Hardware Installation
This chapter provides information on how to install the hardware of
HS-6301. Read sections 1.3, 2.1 and 2.2 about the delivery package and
unpacking information. Afterwards, pay attention to the jumpers setting of
switch, Watch-Dog Timer and the DiskOnChipTM address selection etc.
2.1 Caution of Static Electricity
The HS-6301 has been well packaged with an anti-static bag to protect
sensitive components and circuitry from damage caused by static electric
discharge.
Note：DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT THE NECESSARY ANTI-STATIC
PROTECTION.
You should follow the steps below to protect the board against static
electric discharge whenever you handle the board：
1. Please use a grounding wrist strap on whoever needs to handle the
HS-6301. Clip the ALLIGATOR clip of the strap to the end of shielded
wire lead from a grounded object. Put on and connect the strap before
handling the HS-6301 to harmlessly discharge any static electricity
through the strap.
2. Please use an anti-static pad to put any components or parts or tools
on the pad whenever you work on them outside the system. You may
also use an anti-static bag instead of the pad. Please ask your local
supplier for assistance regarding anti-static requirements.

11
2.2 Caution on Unpacking and Before Installation
Follow the steps in section 2.1 to protect the HS-6301 from electricity
discharge. With reference to section 1.3, please check the delivery
package again with the following steps：
1. Unpack the HS-6301; Store away all packing materials, manual and
diskette, etc.
2. Is there any component missing？DO NOT INSTALL IF THIS
HAPPENS.
3. Is there any visual damaged of the board？DO NOT INSTALL IF THIS
HAPPENS.
4. Check the optional parts (i.e. CPU, SRAM, DRAM, ROM-Disk etc.) to
complete settings of jumpers, jumper pin-set and CMOS setup,
please refer to all information on jumper settings in this manual.
5. Check the external devices (i.e. Add-On-Card, Driver Type etc.). To
complete add-in or connections and CMOS setup correctly, please
refer to all information of connector connections in this manual.
6. Keep the manual and diskettes for re-installation purposes or if you
would like to change the Operating System.

12
2.3 HS-6301’s Layout

13
2.4 Quick Listing of Jumpers
JP1 CPU HOST CLOCK SELECT............................................. P.16
JP2 LCD PANEL VCORE SELECT............................................ P.27
JP3 LCD INVERTER VOLTAGE SUPPORT 12V ............................ P.27
JP4 SCSI ENABLE/DISABLE SELECT....................................... P.32
JP5 CLEAN CMOS (DS12C887 ONLY)................................... P.19
JP6 WATCH-DOG TIMER ACTIVE SELECT.................................. P.17
JP7(1-4) DISKONCHIPTM ADDRESS SELECT...................................... P.16
JP7(5-10) WATCH-DOG TIMER SELECT............................................. P.17
JP8 LAN1 ENABLE/DISABLE SELECT ..................................... P.30
JP9 LAN2 ENABLE/DISABLE SELECT ..................................... P.30
FAN1 CPU COOLER FAN CONNECTOR
FAN2 CPU COOLER FAN CONNECTOR

14
2.5 Quick Listing of Connectors
CN1 RESET(1-2).................................................................. P.21
CN1 KEYLOCK(3-4).............................................................. P.21
CN1 SPEAKER(5-6).............................................................. P.21
CN1 IDE LED(7-8).............................................................. P.21
CN2 ATX POWER ON CONNECTOR.......................................... P.20
CN3 ATX POWER CONNECTOR
CN4 5PIN ATX POWER CONNECTOR......................................... P.20
CN5 5PIN KEYBOARD CONNECTOR........................................... P.26
CN6 PRIMARY IDE CONNECTOR ............................................. P.22
CN7 SECONDARY IDE CONNECTOR......................................... P.22
CN8 SCSI CONNECTOR........................................................ P.32
CN9 IRDA CONNECTOR......................................................... P.30
CN10 FLOPPY DISK CONNECTOR.............................................. P.24
CN11 LCD PANEL CONNECTOR ............................................... P.27
CN12 PC/104 64PIN CONNECTOR............................................. P.33
CN13 PC/104 40PIN CONNECTOR............................................. P.33
CN14 48BIT TFT LCD CONNECTOR........................................... P.27
CN15 PARALLEL CONNECTOR.................................................. P.33
CN16 COMPOSITE & S-VIDEO OUTPUT ...................................... P.27
CN17 SERIAL PORT 1 CONNECTOR (5X2 HEATER)........................ P.25
CN18 SERIAL PORT 2 CONNECTOR (5X2 HEATER)........................ P.25
CN19 INTERNAL LAN1 CONNECTOR (5X2 HEADER)...................... P.30
CN20 INTERNAL LAN2 CONNECTOR (5X2 HEADER)....................... P.30
CN21 INTERNAL CRT CONNECTOR (5X2 HEADER)......................... P.27
CN22 LAN1/LAN2 RJ45 CONNECTOR...................................... P.30
CN23 4PIN MOUSE CONNECTOR................................................ P.26
CN24 CRT CONNECTOR (DB15) .............................................. P.27
CN25 USB CONNECTOR......................................................... P.19
CN26 PS/2 6PIN MINI DIN MOUSE CONNECTOR............................ P.26
CN28 PS/2 6PIN MINI DIN KEYBOARD CONNECTOR....................... P.26

15
2.6 Jumper Setting Description
A jumper pin-set is ON as a shorted circuit with a plastic cap inserted over
two pins. A jumper pin-set is OFF as an open circuit with a plastic cap
inserted over one or no pin between pins. The below figure 2.2 shows the
examples of different jumper pin-set setting as ON or OFF in this manual.
Figure 2.2
All jumper pin-set already has its default setting with the plastic cap
inserted as ON, or without the plastic cap inserted as OFF. The default
setting is referred to in this manual with a “*” symbol in front of the selected
item.

16
2.7 Setting CPU Host Clock
The HS-6301’s JP1 is used for internal Host Bus Clock Ratio.
?? JP1：CPU Host Clock：
JP1 1-23-4
*Auto by CPU ON ON
66.8/33M or BIOS Setting OFF OFF
2.8 DiskOnChipTM Address Setting
The HS-6301 has a U22 socket for a DiskOnChipTM module.
JP7 (pin 1-2, 3-4) is used to select the starting memory address of the
DiskOnChipTM to avoid the same mapping area with any other memory
devices. If you have another extra memory device in the system with the
same memory, neither the HS-6011 nor the extra memory device will
function properly. Please set both with different memory address mapping.
?? JP7：DiskOnChipTM Address
Memory Address JP7 3-4JP7 1-2
*D000 ON ON
D800 ON OFF
（*）：default setting
The D.O.C. function allows the system to run even without FDD or HDD.
The D.O.C. may be formatted just like drive C: or drive A:. Users may also
use the DOS’s commands such as FORMAT, SYS, COPY, XCOPY,
DISCOPY and DISKCOMP. This is means that the D.O.C. may be used
as drive A if the system comes without FDD-A for ambient application.
Please contact your supplier for different sizes of D.O.C. module.

17
2.9 Watch-Dog Timer
There are three access cycles of Watch-Dog Timer: Enable, Refresh and
Disable. The Enable cycle should proceed by READ PORT 443H. The
Disable cycle after a first Enable cycle means Refresh.
Once the Enable cycle is active, a Refresh cycle is requested before the
time-out period to restart counting the WDT’s period. Otherwise, it will
assume that the program operation is abnormal when the time counting is
over and the period preset of WDT Timer. A system reset signal to start
again or a NMI cycle to the CPU comes if over.
JP6 is used to select the active function of Watch-Dog Timer in disable the
Watch-Dog Timer, or presetting the Watch-Dog Timer activity at the reset
trigger, or at the NMI trigger.
?? JP7(5-10)：Time of Watch-Dog
Period 5-67-89-10
*1 sec ON ON ON
2 sec OFF ON ON
10 sec ON OFF ON
20 sec OFF OFF ON
110 sec ON ON OFF
220 sec OFF ON OFF
?? JP6：Watch-Dog Active Setting
JP6 Description
1-2Active NMI
*2-3System Reset
OFF Disable
The Watch-Dog Timer is disabled after the system Power On. The
Watch-Dog Timer can be enabled by a Enable cycle with reading the
control port (443H), a Refresh cycle with reading the control port (443H)
and a Disable cycle by reading the Watch-Dog Timer disable control

18
port (045H). After an Enable cycle of WDT, user must constantly proceed
a refresh cycle to WDT before its period setting comes ending of every 1,
2, 10, 20, 110 or 220 seconds. If the Refresh cycle does not active before
WDT period cycle, the on board WDT architecture will issue a Reset or
NMI cycle to the system.
The Watch-Dog Timer is controlled by two I/O ports.
443H I/O Read The Enable Cycle
443H I/O Read The Refresh Cycle
045H I/O Read The Disable Cycle
The following sample programs showing how to Enable, Disable and
Refresh the Watch-Dog Timer：
WDT_EN_RF EQU 0443H
WDT_DIS EQU 0045H
WT_Enable PUSH AX ; keep AX DX
PUSH DX
MOV DX,WDT_EN_RF ; enable the watch-dog timer
IN AL,DX
POP DX ; get back AX, DX
POP AX
RET
WT_Refresh PUSH AX ; keep AX, DX
PUSH DX
MOV DX,WDT_ET_RF ; refresh the watch-dog timer
IN AL,DX
POP DX ; get back AX, DX
POP AX
RET
WT_DISABLE PUSH AX
PUSH DX
MOV DX,WDT_DIS ; disable the watch-dog timer
IN AL,DX
POP DX ; get back AX, DX

19
POP AX
RET

20
2.10 USB Ports Connector
The HS-6301 has two internal 8pin USB ports connectors. Please refer to
the following for detailed pin information.
?? CN25：8pin USB Port
PIN No. CN25 PIN No. CN25
1VCC 2VCC
3USBV0- 4USBD1-
5USBDO+ 6USBD1+
7GND 8GND
2.11 Setting the RTC Configuration
The HS-6301 provides a setting for the selection of the RTC Clear Jumper
of JP5 setting as following：
?? JP5：Clear CMOS(DS12B887 only)
JP5 CMOS Clear Jumper
*OFF Normal
ON Clear CMOS
2.12 System Memory DRAM
The HS-6301 features four DIMM sockets for memory modules with
access time of 70 n-second or faster. The maximum memory capacity is
1GB.
See the figure on section 2.3 for identifying the banks.