CompuSTAR 2WT13R-SF Technical manual

2WT13R-SF_QuickCard line 20200810.indd 1 2020/08/10 10:20:21
QUICK START
8102REUCL002200 // 2WT13R Guide REV1.0
QUICK START CARD
2WT13R-SF
Firstech, LLC. | 1
Hold this button for 4 seconds to power up the remote.
Tap this button 1 time to lock and/or arm your system.
Double tap this button to activate AUX 2 output when "Secure AUX mode" is disabled.
Hold this button for 5 seconds to activate "panic" or "vehicle locator" feature
NOTE: additional connections may be required.
Tap this button 1 time to unlock and/or disarm your system.
Double tap this button to activate AUX 1 output when "Secure AUX mode" is disabled.
Hold this button for 2.5 seconds to activate rear hatch/trunk release.
NOTE: additional connections may be required.
Hold this button for 2.5 seconds to activate OR cancel the remote start sequence.
Hold this button while in the remote user option for 2.5 seconds to EXIT the user option.
Tap this button 1 time to wake up remote once awake tap again to update the
system status.
Tap this button 1 time to temporarily disable Secure AUX mode.
Double tap this button to ENTER remote user option. Use " / " to
navigate the user features and a single tap of the " " to enter selected
features.
ONLY while the vehicle is remote started, double tap this button to RE-Start
remote start runtime.
Rechargeable Battery: Your 2WT13R-SF
is equipped with a rechargeable battery.
Use the included FT-USB CHARGER to
charge your remote. We recommend
charging your remote before first use.
Charge time is approximately 2 hours.
Register online at www.compustar.com
within 10 days of purchase to activate
your new remote’s warranty.
x 2
5 sec
x 2
2.5 sec
4 seconds
x 2
2.5sec

8102REUCL002200 // 2WT13R Guide REV1.0
2WT13R -SF_QuickCard line 20200810.indd 2 2020/08/10 10:20:21
QUICK START CARD
2WT13R-SF
Firstech, LLC. | 2
REMOTE USER FEATURES
LCD
view
"Full"
Sound/
Vibrate
LCD
brightness
FEATURE FUNCTION/DESCRIPTION FEATURE FUNCTION/DESCRIPTION
Double tap this button to ENTER remote user option. TAP
" / " to navigate the user features left or right and a
single tap of the " " to enter selected features.
This feature will allow you to
select a different vehicle
image for the remote LCD
display. There are 3 options
use " " to select, the
lock/unlock icon will move
to the next feature.
This feature
enables/disables FULL
Alarm or Alarm Remote
Start mode allowing the
remote to receive alarm
trigger alerts.
This feature will allow the
volume of the remote
chime to be adjusted at 3
levels. When set to off, the
remote will be silent with
"vibrate". Use " " to
select level.
This feature will allow the
LCD screen brightness to
be adjust by 3 levels. Use
" " to select level.
AUX 1/
2 Config
Drive
lock
These features allow
AUX 1/2 to be displayed
as optional functions, or
turned off. Use " " to
view options.
This feature will allow
Drive lock/Ignition
controlled Door locks to
be enabled/disabled.
NOTE additional dealer
programming is required.
Power
down
Proximity
UNLOCK
This feature will power
down the LCD remote.
Tap and hold " " for
4 seconds.
This will enable/disable
the proximity unlock
feature of the remote.
NOTE additional dealer
programming required.
Valet Screen
time out
This feature
Enables/Disables Valet
mode. NOTE to enable
Valet mode using T-13,
vehicle ignition/key must
be in the on position.
This Feature will allow the
screen timeout to be
adjusted between 4 and 8
seconds. Use " " to
select.
Language 2nd car
mode
This feature allows the
language of the remote
to be changed between
English, French,
Spanish. Use " " to
view options.
When 2nd car mode is
enabled, this remote can
be programmed to and
control a 2nd vehicle
using a compatible
system.
Tempurature
Siren-Horn
on/off
This feature allows the
remote to display vehicle
internal Temperature (If
Thermistor is installed) in
Fahrenheit or Celcius.
Use " " to select.
This allows the user to
disable the horn/siren
output withkeyless-remote
start functions. NOTE:
when using this feature
the "pre warn" chirps will
also be disabled.
Remote
ID
Shock
Sensor
on/off
This will display the
remote serial number for
idetification.
This will enable/disable
the the shock sensor if
there is one installed.
NOTE: does NOT apply
to remote start only
system.
To reprogram your remote, cycle the key in the ignition 5 times within 7
seconds. Parking lights will flash. Then tap the Lock button on your remote.
Repeat for any additional remotes. All remotes must be programmed during one
sequence. If you receive two parking light flashes, your Compustar has exited
remote programming mode and you must retry.
Questions/comments? Contact us at 888-820-3690 from 8 AM to 5 PM
PST.Also please visit www.compustar.com for a complete user’s manual.
x 2