Concept LED Lights CL-RF-RGBW-KIT User manual

RF RGBW Remote Controller 09.2839W.042302
Operation
Pair with RF receivers:
Click “RF Code Key”
on RF receiver
Function introduction
Important: Read All Instructions Prior to Installation
Output RF signal
Operation Frequency 868/915/434MHz
Operating temperature 0-40°C
Relative humidity 8% to 80%
Dimensions 120x48x17.6mm
Front side
Back side
• Control 1 zone of RF receiver
• RGBW color controller
• Compatible with universal serie RF receiver
• 1 receiver can be paired by max 8 different remote controls.
• Waterproof grade: IP20
Product Data
Safety & Warnings
Power Supply 4.5V(3xAAA battery)
LED lights connected with the
RF receiver will flicker once
Click to switch on/off green channel
Press and hold down to increase/
decrease light intensity
Click to turn ON/OFF
The receiver is paired with
the remote successfully.
Turn on
the remote
Touch the
color wheel
How to delete the pairing:
Press and hold down on the receiver for over 3 seconds until connected LED lights flicker twice,
which means the pairing is deleted successfully.
“RF Code Key”
If you use multiple receivers, you can have all the receivers in the same zone
Lear ning K ey
RF LED Re ceive r
1 Zone RF remote
Lear ning K ey
RF LED Re ceive r
Switch warm white, natural white,
cool white.(Through the three RGB
color mixing)
Color wheel, touch to select color
Click to switch on/off white channel
Press and hold down to increase/
decrease light intensity
Press and hold down to save color,
click to recall the saved
Click to switch on/off red channel
Press and hold down to increase/
decrease light intensity
Click to switch on/off blue channel
Press and hold down to increase/
decrease light intensity
Click to play/pause 10 built-in modes,
press and hold down to speed up/
down the running mode
Press and hold down to increase/
decrease all lights intensity
LED indicator
4.5V(3xAAA battery)
R
G
B
W
S2S1
• This device contains AAA batteries that shall be stored and disposed properly.
• DO NOT expose the device to moisture.

RF RGBW Receiver
Input
Voltage Remarks
Output
Current
12-24VDC Constant voltage
4x(60-120)W
4x5A
Output
Power
RF code key:pair with the RF remote
Waterproof grade: IP20
Radio Frequency : 868/915/434mhz
Function introduction
Important: Read All Instructions Prior to Installation
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
DC Power input
Product Data
Safety & Warnings
Do wiring according to connection diagram.
Pair RF Receiver with RF remote:
1. Connect and wire up the RF receiver correctly, power on.
2. Turn on the remote, click the “RF Code Key” button on receiver, immediately touch the color wheel, the
connected led light on receiver flickers twice, which means well paired.
Note: one receiver can be paired with max 8 remote controls.
Delete the pairing:
1. Wire up the RF receiver correctly, power on
2. Hold down the “RF Code Key” button on receiver for over 3 seconds until the connected led light on
receiver flickers twice, which means well deleted.
MASTER/SLAVE jumper:
In a group of multiple receivers, in order to get a good sync of RGB running effect, please set only 1 receiver as
MASTER, the other receivers as SLAVE.
After setting the Master, the Master receiver need to power off and on once to make the Master function
take effect.
Operation
Size(LxWxH)
145x46.5x16mm
Wiring Diagram
V+ V-
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
12V/24V
CV PSU
RF Code Key
RGBW LED Controller
V+
V-
INPUT
V+
R-
G-
B-
OUTPUT
W-
Common Anode Output(+)
CH 1:R output(-)
CH 2:G output(-)
CH 3:B output(-)
CH 4:W output(-)
MASTER/SLAVE jumper
RGBW LED Strip
V+ V+
R- R-
G- G-
B- B-
W- W-
RF Co de Key
RGBW LED Co ntroller
V+
V-
INPUT
V+
R-
G-
B-
OUTPU T
W-