Conceptronic CMT2D Quick start guide

Copyright® 2009 by Conceptronic – All rights reserved
www.conceptronic.net
Page 1 of 5
Conceptronic CMT2D Firmware Upgrade Instructions
A. Suitable devices
his firmware upgrade is only suitable for Conceptronic CM 2D (Wired version).
Note: This firmware upgrade is not suitable for the Conceptronic CMT2DW (Wireless version)

Copyright® 2009 by Conceptronic – All rights reserved
www.conceptronic.net
Page 2 of 5
B. Upgrade in ormation
A firmware upgrade can improve the performance of your Conceptronic device and can sometimes add new
features.
Periodically firmware upgrades will be available via the official Conceptronic Website.
Conceptronic is not liable for any damages caused by an unofficial, not by Conceptronic approved firmware
for this specific Conceptronic device. Firmware upgrades, even while using official approved firmware, are
always at your own risk.
Installing new firmware without taking the following precautions into account will seriously harm the life
span of your Conceptronic device.
While installing new firmware, make sure the installation procedure is never interrupted.
Interruptions can, amongst others, be caused by:
- turning off the device;
- disconnecting the external USB device from where the upgrade process was started;
- disconnecting the power supply;
- pressing one or more buttons on the remote control or the device;
- a general power shutdown.
Note: If you upgrade the CM 2D with the latest firmware, you need to reconfigure all settings, including
the channels. All stored data on the internal hard disk will not be affected by the firmware upgrade.
Note: he Conceptronic CM 2D can only be upgraded by a USB storage device, like a USB stick or a USB
hard disk.

Copyright® 2009 by Conceptronic – All rights reserved
www.conceptronic.net
Page 3 of 5
C. Upgrade procedure
1. Copying the irmware iles to a USB storage device
1.1 If you have downloaded the firmware upgrade from www.conceptronic.net, you have a ZIP file
containing a folder named ‘Firmware’ and a documentation file for each language.
1.2 Connect the USB storage device to your computer.
1.3 Copy the file ‘UPDATE.WUP’ from the folder ‘Firmware’ to the USB storage device.
(for example: ‘F:\UPDATE.WUP’ where F:\ is your USB storage device).
Note: Do NOT put the firmware file in a folder on your USB storage device The CMT2D must ‘see’ the
firmware file directly on the USB storage device
For example: ‘F:\UPDATE.WUP’
1.4 Remove the USB storage device from your computer. It is recommended to use the safe
remove/eject/unmount option of your operating system.
1.5 Disconnect the USB storage device from your computer.
2. Upgrading the ‘UPDATE.WUP’ irmware
2.1 Connect the CM 2D to your V and a free power wall outlet.
2.2 Connect the USB storage device to one of the USB host ports of the CM 2D.
2.3 he CM 2D will recognize the USB storage device and show the following message:
“Warning: An update has been detected. Checking iles. Please wait…”
2.4 When above warning disappears, the following message will show the following message:
“Do you want to install the update or Grab’n’GO Media Titan, (version 1.2.13.7870) ?”
Select ‘Update’ and press the ‘OK’ button to start the firmware upgrade.
he upgrade will be installed. his can take up to 2 minutes. After the installation, the device will
reboot automatically.
2.5 When the reboot is finished, the message “Update 1.2.13.7870” was success ully installed” will
be shown. Press the ‘OK’ button to close the message.
Note: If the firmware upgrade is finished, the CMT2D will show the setup wizard in order to
reconfigure the device After the reconfiguration, it is necessary to turn the device completely
off and on by disconnecting the powersupply, before you start using the device again
Note: If the message ‘You are already using a more recent firm are’ is shown, this means you are
trying to upgrade with an older firmware, or the firmware on the USB storage device is already
installed on your CMT2D

Copyright® 2009 by Conceptronic – All rights reserved
www.conceptronic.net
Page 4 of 5
D. Checking the irmware version o the CMT2D
1.1 When the CM 2D is in the main menu, select ‘Setup’.
1.2 In the ‘Setup’ menu, select ‘Version’.
he CM 2D will show the Version screen where you can see the current firmware version of the CM 2D.
his should be:
So tware version: 1.2.13.7870
1.3 Press the ‘Menu’ button on the remote control to return to the CM 2D main menu.

Copyright® 2009 by Conceptronic – All rights reserved
www.conceptronic.net
Page 5 of 5
E. Release notes
CMT2D Version 1.1.13.7870:
Added:
Added Italian language
CMT2D Version 1.1.13.7860:
Initial release