Concord Camera 5040 User manual

1
User’s Guide

1
TABLE OF CONTENTS
CAMERA OVERVIEW
System Requirements ...................................................................................................................................3
Safety Information..........................................................................................................................................3
FCC Compliance and Advisory .....................................................................................................................4
Package Contents .........................................................................................................................................5
Camera Components ....................................................................................................................................6
PREPARING THE CAMERA
Charging the Batteries ..................................................................................................................................7
Installing the Batteries....................................................................................................................................7
Inserting an SD Card .....................................................................................................................................8
Turning the Power On / Off............................................................................................................................8
Setting the Date and Time .............................................................................................................................9
Setting the Camera Mode..............................................................................................................................9
Information Displayed on the LCD...............................................................................................................10
Operating the Multi-controller.......................................................................................................................11
Using the MENU ..........................................................................................................................................11
Setting Date Printing ....................................................................................................................................13
Setting the Language...................................................................................................................................13
TAKING PICTURES
Basic Still Image Shooting ..........................................................................................................................14
Using the Digital Zoom ...............................................................................................................................14
Using the Flash ............................................................................................................................................14
Taking Pictures in Macro Mode....................................................................................................................15
Setting the Image Quality and Resolution ...................................................................................................15
Taking Pictures with the Self-Timer..............................................................................................................16
Setting the Exposure....................................................................................................................................16
Setting the White Balance............................................................................................................................16
TAKING VIDEO CLIPS ...................................................................................................................................17
TAKING AUDIO CLIPS...................................................................................................................................17
REVIEWING THE STORED FILES
Reviewing Files............................................................................................................................................18
Magnifying Pictures......................................................................................................................................18
Viewing Files in Thumbnail Mode ................................................................................................................18
Protecting Files ............................................................................................................................................18
Deleting Files ...............................................................................................................................................19
Running Slide Show ....................................................................................................................................20
ENGLISH

2
Copying Files ...............................................................................................................................................20
Formatting Internal or SD Card Memory......................................................................................................20
SETTING FILE NUMBER & PRINTING ORDER
About File Number and Folder Capacity ....................................................................................................21
Setting File Number .....................................................................................................................................21
Selecting Pictures for Printing .....................................................................................................................22
Setting USB Mode .......................................................................................................................................22
Printing Pictures Directly …………………....................................................................................................23
MAKING CONNECTIONS
Viewing Files on Your TV .............................................................................................................................25
Downloading Files onto Your Computer ......................................................................................................25
Downloading by Using an SD Card Reader...........................................................................................25
Downloading by Using with the USB Cable ...........................................................................................26
INSTALLING SOFTWARE (WINDOWS)
Using the Splash Screen .............................................................................................................................27
Installing the Camera Driver .......................................................................................................................28
Installing Windows Media Player 9 ..............................................................................................................29
Installing Arcsoft Photoimpression 2000......................................................................................................31
Installing Adobe Acrobat Reader 6 ..............................................................................................................34
Using the Arcsoft Photoimpression ..............................................................................................................37
APPENDIX
Troubleshooting............................................................................................................................................38
Specifications ...............................................................................................................................................39
Getting Help .................................................................................................................................................40

3
CAMERA OVERVIEW
SYSTEM REQUIREMENTS
Windows:
• PC with processor better than MMX Pentium 300 MHz
• Windows 98 SE (Second Edition)/2000/ME/XP
• Minimum 128 MB RAM
• USB port
• CD-ROM drive
• 1024 x 768 monitor, 24-bit color (true color)
Macintosh:
• Power Mac G3 or later
• Mac OS 9.0, 9.1, 9.2 and OS X
• Minimum 64 MB RAM
• USB port
• CD-ROM drive
• 640 x 480 monitor with thousands of color (millions of color recommended)
Specifications are subject to change without prior notice.
SAFETY INFORMATION
• Before using the camera, please ensure that you read and understand the safety precautions described
below. Always ensure that the camera is operated correctly.
• Do not aim the camera directly into the sun or other intense light sources that could damage your
eyesight.
• Do not try to open the case of the camera or attempt to modify this camera in any way. High-voltage
internal components create the risk of electric shock when exposed. Maintenance and repairs should be
carried out only by authorized service providers.
• Do not fire the flash too close to the eyes of animals or people, especially for young children. Eye damage
may result. In particular, remain at least one meter away from infants when using flash.
• Keep the camera away from water and other liquids. Do not use the camera with wet hands. Never use
the camera in the rain or snow. Moisture creates the danger of fire and electric shock.
• Keep the camera and its accessories out of the reach of children and animals to prevent accidents or
damage to the camera.
• If you notice smoke or a strange odor coming from the camera, turn the power off immediately. Take the
camera to the nearest authorized service center for repair. Never attempt to repair the camera on your
own.
• Use only the recommended power accessories. Use of power sources not expressly recommended for
this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards.
CAMERA OVERVIEW

4
FCC COMPLIANCE AND ADVISORY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.) This device may not cause harmful interference, and 2.) This device must accept any interference
received, including interference that may cause unsatisfactory operation.
This equipment has been tested and found to comply with the limits for a Class B peripheral, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment. When shielded interface cables have been provided with the
product or when specified additional components or accessories have elsewhere been designated to be used
with the installation of the product, they must be used in order to ensure compliance with FCC regulations.
CAMERA OVERVIEW

5
PACKAGE CONTENTS
Please contact your dealer immediately if any of the items below are missing or damaged.
Camera USB Cable TV out cable
Soft Case Battery Charger 2x AAA Rechargeable Batteries
Software Installation Wrist Strap Quick Start Guide
CD-ROM (including
multilingual User’s Guide)
CAMERA OVERVIEW

6
CAMERA COMPONENTS
CAMERA OVERVIEW
2
3
1
4
9
8
5
6
7
9. MENU button
10. Multi-controller
- Push upward ( ) = Set Flash mode / Move cursor up
- Push downward ( ) = Set Self-Timer / Move cursor down
- Push to right ( ) = Zoom in / Move cursor to right
- Push to left ( ) = Zoom out / Move cursor to left
- Press down = SET
1. Strap mount
2. Flash
3. Lens
4. Self-timer lamp
5. Power button
6. Operation lamp
7. LCD screen
8. Camera mode button
10
11. Macro switch
12. USB port
13. TV OUT terminal
14. Shutter button
15. Microphone
16. SD Card/Battery Cover
17. Tripod Socket
18. Speaker
14 15
16 17 18
11
12
13

7
PREPARING THE CAMERA
CHARGING THE BATTERIES
The supplied battery charger can charge up to two pieces of AAA and or AA size batteries.
1. Insert the supplied rechargeable batteries into the charger with its (+) and (-) ends
matching the polarity indication engraved inside the charger.
2. Plug the charger into a standard AC power outlet. The green indicators will light up.
3. It will take around 25 hours for the batteries to be fully charged. When the
batteries are fully charged, unplug the charger from AC outlet first, and then
remove the batteries.
Note:
1. If the green indicators did not light up, check if the batteries are loaded correctly.
2. It is normal for batteries to become ware while charging.
3. The green indicators will remain on when batteries are fully charged. Judge if the batteries are fully
charged by noting down the charging time.
4. To reduce the risk of injury, charge only Ni-MH / Ni-CD batteries with this charger. Other types of
batteries might burst, causing personal injury and damage.
INSTALLING THE BATTERIES
NOTE: The supplied rechargeable batteries are not charged when you receive them. Charge them before
loading them into the camera.
1. Slide the Battery/Memory Card door in the direction of the arrow,
and lift it open.
2. Insert two AAA batteries with the positive (+) and negative (-) poles
matching the directions indicated inside the battery cover.
3. Close the Battery/Memory Card door.
Battery Status Indications
The LCD monitor displays an icon to let you know battery status.
Battery Level High Low
Indicator
When low battery icon is shown on the LCD, recharge the batteries or replace the batteries with new ones.
AAA
AAA
PREPARING THE CAMERA

8
INSERTING AN SD CARD
The digital camera is equipped with a 32MB internal memory. If no SD card is inserted in the camera, all
pictures/video clips/audio clips recorded by the camera will be stored in the internal memory. When SD card
is inserted in the camera, all files recorded by the camera will be stored on the SD card by using the Design
Rule for Camera File System (DCF) protocol. The DCF protocol is designed to accommodate file and data
exchange between digital cameras and other devices. Photos that are taken by a DCF camera can be viewed
on DCF-compatible cameras from other manufacturers.
1. Turn off the camera.
2. Open the Battery/Memory Card Door.
3. Insert the SD card in the direction as shown in the figure aside.
4. Close the Battery/Memory Card Door.
Note: When the SD card is being written to, read, erased or transmitted to, the green operation lamp
located on the left side of the Power button will blink. Do not turn off the camera or open the Battery
Memory Card Door while the LED is blinking.
To remove the SD card
1. Turn off the camera.
2. Open the Battery/Memory Card Door.
3. Gently press on the edge of the SD card to release it.
4. Pull the card out and close the Battery/Memory Card door.
TURNING THE POWER ON/OFF
Press and hold the POWER button for more than 1 second to turn the camera on.
To turn off the camera
Press the POWER button to turn off the camera.
Note:
1. The camera will be powered off automatically after being idle for some time. The Auto-Off timing can
be changed in Setup menu.
2. If the camera cannot be powered on, the batteries may be drained. Replace or recharge the battery
and try again.
PREPARING THE CAMERA

9
SETTING THE DATE AND TIME
The setting Date/Time screen will pop up when powering the camera on for the first time or when the batteries
are removed for an extended time.
1. Press or to select a field to change.
2. Press or to set the values.
3. After the Date and Time is set, press the SET button to confirm the
settings and to exit.
To adjust Date/Time or to change Date/Time format:
1. Press the MENU button.
2. Press to select the Setup Menu.
3. Press or to select Date & Time then press the SET button or to enter its submenu.
4. Follow steps 1-3 in the above section to set Date, Time and or Date/Time format.
SETTING THE CAMERA MODE
Press the MODE button to change camera mode.
Shooting Mode For shooting still images
Video Mode For shooting video clips.
Voice Mode For recording audio clip.
Review Mode For viewing the recorded images, video clips and or audio clips.
The camera mode changes as shown in the following diagram when the MODE button is pressed.
Shooting Mode Video Mode Voice Mode Play Mode
PREPARING THE CAMERA
07/25/2004 21:45
MM/DD/YY

10
INFORMATION DISPLAYED ON THE LCD MONITOR
The LCD displays information such as the camera settings, remaining image capacity and shooting date etc.
Shooting Mode
Playback Mode
1 Battery Status
2 White Balance
3 Exposure
4 Shooting Mode
5 Flash Mode
6 Macro Mode
7 Self-Timer
8 Resolution Setting
9 Compression Setting
10 Memory Type
11 Aperture Value
12 Shutter Speed
13 Number of Recordable Images
14 Playback Mode
15 Protect
16 Display Image/Total
17 Memory Type
18 Battery Status
19 File Number
20 Shooting Date
1
2
3
4
5678
9
1
0
13
1
2
1
1
1614 17
18 19 20
15
PREPARING THE CAMERA

11
OPERATING THE MULTI-CONTROLLER
The multi-controller is used to set shooting mode, to move cursor when the camera Menu is shown, and to
confirm the selection.
Push Up (“ ” is named hereafter)
• To set Flash mode in Shooting Mode.
• To move the cursor up when MENU screen is shown.
Push to Right (“ ” is named hereafter)
• To zoom in subjects in shooting mode or to magnify image in review mode.
• To move the cursor to right when MENU screen is shown
• To enter submenu.
Push Down (“ ” is named hereafter)
• To set Self-Timer in Shooting Mode and Video Mode.
• To move the cursor down when MENU screen is shown.
Push to Left (“ ” is named hereafter)
• To zoom out.
• To move the cursor left when MENU screen is shown.
• To set Thumbnail view in Review mode.
Press Down (“SET” is named hereafter)
• To enter submenu.
• To confirm the setting.
ABOUT MENUS AND SETTINGS
Use the menus as shown below to activate the various shooting and reviewing settings.
1. Press the MENU button.
2. Press or to switch between the REC/Playback Menu and Setup Menu.
3. Press or to select a menu item then press the SET button or to
enter its submenu.
4. Press the , , or to select the settings you wish to set then press
the SET button.
5. Press the MENU button to close the menu window.
Multi-controller
PREPARING THE CAMERA
2592 x1944

12
This chart shows the options for each menu settings.
Menu Item Available Setting
Shooting Mode
Menu
Resolution 2592x1944,2048x1536,1280x960, 640x480
Quality Fine / Normal
Exposure +2/+1.7/+1.3/+1.0/+0.7/+0.3/Auto/-0.3/-0.7/-1.0/-1.3/-
1.7/-2.0
White Balance Auto / Daylight / Shade / Tungsten / Fluorescent
Date Stamp On / Off
Setup Menu
Quick View On / Off
Beep On / Off
Power Off Off / 1 min / 2 min
Date & Time Sets the date and time
File NO. Reset On / Off
TV Out NTSC/PAL
Language English / Traditional Chinese / Simplified Chinese /
Japanese / Korean / German / French / Portuguese /
Italian / Spanish / Dutch / Russian
Format No / Yes
USB Computer/Printer
Playback
Mode Menu
Protect Single / Lock All / Unlock All
Delete All Single / All
Slide Show Off / 5 sec / 10 sec
Print Order Single / All / Reset
Copy To Card No / Yes
Movie Mode
REC Menu
Movie Resolution 640x480,320x240
Quality Fine / Normal
Exposure +2/+1.7/+1.3/+1.0/+0.7/+0.3/Auto/-0.3/-0.7/-1.0/-1.3/-
1.7/-2.0
White Balance Auto / Daylight / Shade / Tungsten / Fluorescent
Note: MENU button is disabled in Voice mode.
PREPARING THE CAMERA

13
DATE STAMP
By default the Date Stamp is set at OFF mode. If you want to have Date and Time shown on the pictures, set
the Date Stamp to ON mode.
1. Press the MENU button.
2. Press or to select Date Stamp then press the SET button or to
enter its submenu.
3. Press or to select On or Off.
4. Press the SET button to confirm the selection.
5. Press the MENU button twice to close the menu window.
SETTING THE LANGUAGE
1. Press the MENU button.
2. Press to select the Setup Menu.
3. Press or to select Language then press the SET button or to
enter its submenu.
4. Press or to select a Language.
5. Press the SET button to confirm the setting and to close the menu
window.
2592 x1944
PREPARING THE CAMERA

14
TAKING PICTURES
BASIC STILL IMAGE SHOOTING
1. Make sure the camera is in still image shooting mode ( ).
2. Frame the subject in the LCD.
3. Press the Shutter button fully down to capture the image.
USING THE DIGITAL ZOOM
The camera provides up to 4x digital zoom.
1. Press to zoom in subject for a telephoto shot.
• The zoom indicator shows the current approximate zoom factor.
2. Press to zoom out for a wide angle shot.
USING THE FLASH
Use the flash according to the guidelines below.
Auto The camera judges if a flash is required. If the environment is
too dark, the flash will fire.
Force On The flash always fires.
Force Off The flash does not fire.
1. Press to switch between flash modes.
• The selected flash mode icon appears on the LCD monitor.
2. Shoot the image.
Note:
1. The indicator beside the Power button will blink in red when the camera is charging the Flash. Wait
until the indicator stops blinking then to take a flash picture.
2. When batteries are low, the Flash will be disabled. If you found that the Auto Flash ( ) or Force
Flash ( ) cannot be activated by pressing , replace or recharge the batteries.
The current approximate
zoom factor
TAKING PICTURES

15
TAKING CLOSE-UP PICTURES
Use the macro mode to shoot close-up of subjects in the range of 20 cm (7.87 inches).
1. Slide the Macro switch to the( )position.
• The icon appears on the LCD monitor.
2. Shoot the image.
Note:
1. Always remember to slide the Macro switch back to Landscape position ( ) when close-up
shooting is not required.
2. Focus range mentioned is the distance between the camera lens surface and the subject.
SETTING THE IMAGE QUALITY AND RESOLUTION
You can change the image quality and resolution to suit your purpose. Higher
settings contain more details and have larger file sizes.
1. Press the MENU button.
2. Press or to select Resolution or Quality then press the SET button
or to enter its submenu.
3. Press or to select the settings you wish to set then press the SET
button.
4. Press the MENU button to close the menu window.
Resolution Purpose
(Large) 2592 x 1944 Print large prints
(Medium 1) 2048 x 1536 Print on small size paper
(Medium 2) 1280 x 960 Send images by e-mail
(Small) 640 x 480 Shoot more images
Image Quality Purpose
Fine Shoot high quality images
Normal Shoot normal quality images
Macro
switch
2592 x1944
TAKING PICTURES

16
TAKING PICTURES WITH SELF-TIMER
Use the self-timer to set a delay from the time the shutter button is pressed to the time the image is shot.
1. Press to switch between self-timer modes until the desired mode icon appears on the LCD.
2. Shoot the image.
Setting Description
Blank Without delay
Two seconds delay
Ten seconds delay
Photography hints:
Since the red Self -Timer LED in the front of the camera will blink after the Shutter button is fully
pressed down, you have time to join in the photograph and know when the camera is done taking a
picture when the self-timer LED stops blinking.
ADJUSTING THE EXPOSURE---EV ADJUSTMENT
The camera uses Auto Exposure to give well-exposed pictures under most
lighting conditions. If the captured picture of the main subject turns out to be
too light or too dark, use the Exposure Compensation feature to improve the
exposure aspect.
1. Press the MENU button.
2. Press or to select Exposure then press the SET or to enter its
submenu.
3. Press or to set the exposure compensation value. Available settings
are:-2.0, -1.7, -1.3, -1.0, -0.7, -0.3, Auto, +0.3, +0.7, +1.0, +1.3, +1.7, +2.0.
4. Press the SET button to confirm.
ADJUSTING COLOR TONES---SETTING THE WHITE BALANCE
By default the camera uses Auto White Balance to reproduce colors under different lighting conditions.
For mixed lighting conditions, it is recommended to use the Auto White Balance option. However, if the
lighting condition is identical to one of the following White Balance settings, set the White Balance to the
corresponding mode to get pictures with colors more accurately.
Auto The camera will automatically choose the white balance setting.
Day light For recording outdoors on a sunny day
Shade For recording under overcast, shady or twilight skies
Tungsten For recording under tungsten lighting
Fluorescent For recording under fluorescent lighting
1. Press the MENU button.
2. Press or to select white balance then press the SET or to enter its submenu.
2592 x1944
TAKING PICTURES

17
3. Press or to set the desired white balance mode then press the SET button to confirm.
TAKING VIDEO CLIPS
The digital camera can shoot video clips with audio.
1. Press the MODE button repeatedly until the video mode icon ( ) appears on the LCD.
• The LCD monitor displays the maximum recordable time (in minute).
2. Press the Shutter button to start recording.
3. Press the shutter button again to stop recording. Otherwise the camera stops recording automatically when
the memory capacity is reached.
Note:
1. Be careful not to touch the microphone which is located at the top side of the camera while
recording video or audio clips.
2. The Video resolution can be set to 640 x 480 or 320 x 240 pixels.
3. The Self-Timer and Macro mode shooting can be activated in Video Mode.
4. The Image Quality, Exposure compensation and White Balance can be adjusted before recording
video clip.
TAKING AUDIO CLIPS
You can use the camera as an audio recorder.
1. Press the MODE button repeatedly until the voice mode icon ( ) appears on the LCD.
2. Press the Shutter button to start recording an audio clip. The green Operation Lamp will blink.
3. Press the Shutter button again to stop recording. Otherwise, it will stop automatically after the memory
limit isreached.
2592 x1944
Recordable time Recording time
Recording time
Recordable time Recording time
TAKING VIDEO CLIPS / AUDIO CLIPS

18
REPLAYING STORED FILES
REVIEWING THE STORED FILES
You can view the recorded images, video clips and audio clips on the
camera.
1. Press the MODE button repeatedly until the review mode icon ( )
appears on the LCD. The last recorded file appears on the LCD monitor.
2. Press to move to the previous file and press to move to the next file.
3. When a video clip or audio clip is selected, press the SET button to start
playing the file.
MAGNIFYING THE STORED IMAGES
Still images can be magnified up from 1 times to 8 times.
1. When the desired image is shown on the LCD, press to enlarge the
image, and press to zoom out. The zoom factor is shown on the LCD.
2. Press the SET button to confirm the selected magnifying level.
3. Press , , or to navigate in the image.
4. Press the SET button again to resume zooming mode.
VIEWING THE STORED FILES IN THUMBNAIL MODE
You can view up to nine files at a time on the LCD monitor.
1. Press the MODE button repeatedly until the review mode icon ( )
appears on the LCD.
2. Press . Up to 9 thumbnail files is shown on the LCD.
3. Press the SET button. The last file is highlighted in red border.
4. Press , , or to select the desired file.
5. Press the SET button to display the selected file in full screen size.
PROTECTING THE STORED FILES
You can protect important files from being accidentally erased by locking the files.
Locking Files Individually.
1. Press the MODE button repeatedly until the review mode icon ( )
appears on the LCD.
2. Press or to select the file to be protected.
3. Press the MENU button.
4. Press to highlight Protect and then press the SET button or to enter
its submenu.
5. Press or to select Single, then press the SET button or to enter
its submenu.
6. Press or to select Yes, then press the SET button to confirm. A key
shape icon will be shown on the LCD, which indicates the file is locked.
The zoom factor is shown
REPLAYING STORED FILES

19
7. Press or to look for other files to be protected, then press the SET button to lock the selected file.
8. Press the MENU button to exit file-protecting mode.
Locking All Files
1. Press the MODE button repeatedly until the review mode icon ( ) appears on the LCD.
2. Press the MENU button.
3. Press to highlight Protect and then press the SET button or to enter its submenu.
4. Press or to select Lock All, then press the SET button or to enter its submenu.
5. Press or to select Yes, then press the SET button to confirm. All the files will be locked.
Unlocking Files
To unprotect all the files, follow steps above but select “Single” or “Unlock All“ when protect Menu is shown
on the LCD.
DELETING UNWANTED FILES FROM MEMORY
Erase files that you don’t want to keep to make more memory space available. You can erase individual files
or all files in Playback Mode.
Deleting Files Individually
1. Press the MODE button repeatedly until the review mode icon ( )
appears on the LCD.
2. Press or to select the file to be deleted.
3. Press the MENU button.
4. Press to highlight Delete ALL and then press the SET button or to
enter its submenu.
5. Press or to select Single, then press the SET button or to enter
its submenu.
6. Press or to select Yes, then press the SET button to confirm.
7. Press or to find out other files to be deleted, and then press the SET
button to delete the selected files.
8. Press the MENU button to exit file-deleting mode.
Deleting All Unlocked Files
1. Press the MODE button repeatedly until the review mode icon ( ) appears on the LCD.
2. Press the MENU button.
3. Press to highlight Delete ALL and then press the SET button or to enter its submenu.
4. Press or to select All, then press the SET button or to enter its submenu.
5. Press or to select Yes, then press the SET button to confirm. All the unprotected files will be
deleted.
Note: To delete protected file, please unlock the file first.
REPLAYING STORED FILES