Congatec conga-PA5 Series User manual

conga-PITX
Chassis for congatec Pico-ITX Modules
Quick Start Guide
Revision 1.0

Copyright © 2019 congatec AG conga-PITXq10 2/3
1 Introduction
1.1 Supported Boards
The conga-PITX supports a range of congatec modules as shown in the table below:
Part No - Chassis Part No - Supported Boards
052556 - conga-PA5/Chassis PIX-APH1 lidded,
commercial temperature
048100 - conga-PA5/E3950-8G
048101 - conga-PA5/E3940-4G
048102 - conga-PA5/E3930-4G
052557 - conga-PA5/Chassis PIX-APH1 non-lidded,
commercial temperature
048120 - conga-PA5/N4200-8G
048121 - conga-PA5/N3350-4G
048123 - conga-PA5/N4200-4G
1.2 What is in the Package
Contents
① ② ③ ④
⑤ ⑥ ⑦ ⑧
⑨ ⑩ ⑪
⑫⑬
1. The received product may differ slightly from the illustrations in this guide. While the drawings
may differ, the basic steps described in this guide remains the same.
2. For optimal storage installation, use right-angled SATA cables. To order from congatec AG,
use the following part numbers: 48000030 (SATA data) and 14000205 (SATA power)
3. Apply thermal compound only on variants with non-lidded CPU (PN: 052557)
x2
Note
1.3 Front Panel Layout
1.4 Back Panel Layout
1.5 Internal Layout
1.6 Internal PCB
The motherboard may damage if you connect the panel to the wrong headers. Check the
specific module's manual for connection tips.
USB 2.0 portHard drive LED Power LED
Power switch
COM Port
USB 3.0 LAN
USB CPower DP++
USB
ACPU stack BFront panel PCB CMainboard standoffs DMounting hole for HDD/SSD bracket
DD
D D
C C
CC
A
B
USB cable
LED cable
2-pin Power
switch
PWR & HDD
LED
USB 2.0
connector
USB 2.0
connector
Note
x2
x2 x8 x2
x4
① HDD protective film
⑤Copper block (for PN:052557 )
⑦ Chassis Panels with PCB
⑩Cables (LED, USB, COM)
⑨VESA mounting screw⑧Motherboard screws and washers
⑪Case feet items
④VESA mount bracket ⑥Thermal compound
③2.5" HDD/SSD screws②2.5" HDD/SDD mounting bracket
⑫Gap pad ⑬COM port screw

Copyright © 2019 congatec AG conga-PITXq10 3/3
2 Installation
2.1 Assembly
1. Remove the back cover: 2. Mount the COM cable to the chassis
(if required)
3. Remove the blue film from the gap
pad:
4. Place the gap pad on the heat sink
and remove the transparent film
5. Place the copper block on the gap
pad (only for PN: 052557):
6. Apply the CPU thermal compound
(only for PN: 052557):
7. Connect the COM cable to the
board (if required):
8. Mount the congatec board. Screw
positions are shown below:
⑩
⑬
⑥
CPU
⑧
9. Connect LED and USB cables from
front panel to congatec board:
10. Secure the HDD protection and the
brackets to the hard drive:
11. Connect SATA cables to HDD and
mount assembly to chasis:
12. Attach the back cover and the case
feet items:
2.2 VESA Mounting
1. Attach VESA mounting screw: 2. Detach case feet items:
3. Mount the VESA bracket: 4. Align the chassis:
USB2.0 connector
Red Orange
White Brown
Yellow
Blue
KEY
Purple
Black
GND
- White + Red H.D.D LED - White + Green Power LED - White + Orange Power
Empty Empty Empty Empty Empty Empty
2.5” HDD / SSD
②
①
③
PN: 48000030 PN: 14000205
⑪
⑨
⑪
⑪
④