Connected RFK2101 User manual
CONNECTED OWNER'S GUIDE
2
4-7
8
10
powe by:
lighave
TECH NOLOGY
Technology FM 2-WAY SST
Max. Range 5000 feet
Buttons 1
Transmit Confirmation (TX) LED
Receive Confirmation (RX) LED + Chime
Batteries Required 2 x CR2016
Avg. Battery Life 1 Year
Warranty 1 year
REMOTE OVERVIEW
Please take a moment to familiarize yourself with your Connected RTX2100 remote’s general features.
CONNECTED OWNER’S GUIDE
REMOTE MODEL RFK2101
NOTES:
1. All functions must be enabled by an Authorized Dealer during installation to
be functional on remote
2. = Press & release button
3.
= Press & hold button for the amount of seconds indicated in the center of icon.
4. Coma (,) between icons = Press buttons one after the other
5. Timeout between each button press = 3 seconds
This Single button transmitter can be configured in 3 different way to change it’s behaviour with your vehicle.
To configure your transmitter, please follow the steps below.
1- Choose which configuration mode is desired from the next pages of this guide.
2- Once the Configuration mode is chosen, Press and hold the button on the transmitter for at least
10 seconds. The White LED will blink once + 1 chirp.
3- Then the White LED will blink 1 or 2 or 3 times to display the current transmitter configuration mode.
(you now have 10 seconds to proceed to Step 4)
4- Press and Release the button until the White LED blinks the desired configuration mode.
5- When the White LED is blinking the desired selection, Press and Hold the transmitter button for 10 seconds.
After 10 seconds, the White LED will blink the 1 or 2 or 3 blinks depending on the saved configuration mode.
6- Release the transmitter button.
Note: To exit programming at any time, do not press transmitter button for at least 10 seconds. Also removing
the batteries will not alter the programmed configuration mode.
COMMAND
S & CONFIRMATIONS
In order to get the most out of your Connected RFK2101 remote, please take a moment to get
acquainted with the following commands and confirmations below:
5s
COMMAND DESCRIPTION
Extended Runtime 3 chirps, 1 Flash of Blue LED
,
Seamlessly extends your
engine runtime without
restarting your vehicle.
COMMAND
Lock & Arm
Unlock & Disarm
Starts the engine.
Secures your vehicle by
locking the doors and
arming the factory alarm.
2 long chirps then
3 chirps, 2 flashes of Blue LED
Stop
Start
1 chirp, 1 flash of Blue LED
2 chirps, 2 flashes of Blue LED
2 chirps, 1 flash of Blue LED
While engine is remote
started. Stops the engine.
,
2 long chirps then
3 chirps, 2 flashes of LED
Cold Weather Mode
Accesses your vehicle by
unlocking the doors and
disarming the factory alarm.
CONFIGURATION MODE 1 (default)
Displays remote firmware
version inside remote.
Query Remote
Firmware Version
Transmitter transmit LED blinks :
- 1x flash, pause, 3 flash = V.1.3
3s
5s
5s
15s
20s
CONNECTED OWNER’S GUIDE
3s
While engine is not
remote started.
.
&o
a
&o
a
:,
*"
:2
CONNECTED OWNER'S GUIDE
powe by:
lighave
TECH NOLOGY
COMMAND DESCRIPTION
CONFIGURATION MODE 2
While engine is not
remote started.
o,
O"�
o,
:,
*"
:2
CONNECTED OWNER'S GUIDE
.
'
powe by:
lighave
TECH NOLOGY
.
COMMAND DESCRIPTION
CONFIGURATION MODE 3
While engine is not
remote started.
While engine is not
remote started.
CONNECTED OWNER’S GUIDE
REPLACING REMOTE BATTERIES
Follow the steps below to replace the batteries in your Connected remote:
1. On the backside of your remote, remove the 2x mini-phillips screws and seperate
the front and back part from the transmitter.
2. Remove the old batteries and replace by two new CR2016 batteries.
3. Close back the front and back of the transmitter and reinstall the 2x screws.
WHEN SERVICING YOUR VEHICLE
To ensure safety during vehicle servicing, the remote starter must be placed in “Valet Mode”. The
“Valet Mode” will disable remote start functionality. See your Remote starter manual for Valet mode procedure.
CONNECTED OWNER'S GUIDE
REMOTE RT TROUBLESHOOTING
powe by:
lighave
TECH NOLOGY
ONE-YEAR LIMITED WARRANTY
Lightwave Technology Inc. warrants to the original purchaser of the Connected product that the
following components product shall be free of defects in material and workmanship under normal use
and circumstances for the period of one (1) year from the date of original installation, excluding battery
replacement.
In the event of any product malfunction during the Warranty period, the original purchaser must return
to the Authorized Dealer where it was originally purchased with the original proof of purchase. If a
malfunction is detected, the Authorized Dealer will elect to repair or replace the product at its
discretion. Labor costs may be applicable and are at the discretion of the Authorized Dealer.
THE ONE-YEAR LIMITED WARRANTY IS AUTOMATICALLY VOID IF:
An original proof of purchase is not provided when servicing the product
during the warranty period;
The Connected product is transferred to another vehicle;
The vehicle in which the product was originally installed is transferred to a new owner.
Lightwave Technology Inc. is not responsible for any damages whatsoever, including but not limited to
any consequential damages, incidental damages, damages for loss of time, loss of earnings,
commercial loss, loss of economic opportunity and the like that may or may not have resulted from the
installation or operation of a Connected product.
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation
of the device.
CAN ICES-3 (B)/NMB-3(B)
Tested to comply
with FCC Standards
Table of contents
