Connection Technology Systems EPS-2010G User manual

Trademarks
CTS is a registered trademark of Connection Technology Systems
Inc. Contents subject to revision without prior notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in part, in
any way whatsoever unless prior consent has been obtained from
Connection Technology Systems Inc.
FCC Warning
These devices have been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These standards are designed to provide reasonable
protection against harmful interference when these devices are
operated in a commercial environment. These devices generate,
use, and can radiate radio frequency energy and may cause
harmful interference to radio communications unless installed in
accordance with this Quick Installation Guide. Operation of these
devices in a residential area is likely to cause harmful interference
which will make the user responsible for the appropriate remedial
action at his / her own expense.
CE Mark Warning
These are Class A products. In a domestic environment these
products may cause radio interference in which case the user will
need to consider adequate preventative methods.
1. Checklist
The package should contain the following items:
-
PoE Switch
-
AC Power Cord
-
Four Rubber Feet
-
Rack-mounting Bracket Kit
-
Quick Installation Guide
-
SFP dust cap x 1
Please notify your sales representative immediately if any item is
missing or damaged.
As for power adapters, please refer to Section 8 for more detailed
information.
2. Overview
This PoE Switch is compact 9-inch, rack mountable, has 8-port
10/100BASE-TX 802.3at PoE+ with 1-port 10/100/1000BASE-T +
1-port 100/1000BASE-X SFP switch in front panel. This PoE
Switch provides high performance store and forward switching
plus built-in DIP switch that provides “Default”, “VLAN” and
“CCTV” mode.
Clear, at-a-glance per-port LED indicators make users easier to
monitor network and PoE status. EPS-2010G supports IEEE
802.3af/at PoE technology, up to 30W per port and maximum
100-meter transmission distance and supports a maximum of
120W of total PoE budget.
Major Features:
3. Switch Front Panel
Figure 1 shows the front panel of EPS-2010G
Figure 1. EPS-2010G Front Panel
4. LED Description
Power LED
LED
Color
Function
Power
Off
Power is off.
Green
Indicates the switch has power.
Port LED 1~8
LED
Color
Function
Link/ACT
Off
No connection
Green
Light: Indicates the link through that port
is successfully established at
10/100Mbps.
Blink: Indicates the switch is actively
sending or receiving data over that port.
Off
No powered device (PD) connected
PoE
Orange
Light: There is a PoE PD connected to
be port, which supply power
successfully.
Blink: Indicates port abnormal power
supply.
Port LED 9
LED
Color
Function
Link/ACT
Off
No connection
Green
Light: Indicates the link through that port is
successfully established.
Blink: Indicates the switch is actively
sending or receiving data over that port.
Speed
Off
Indicates the link through established at
10/100Mbps
Green
Indicates the link through established at
1000Mbps
Port LED 10
LED
Color
Function
Link/ACT
Off
No connection
Green
Light: Indicates the link through that port is
successfully established.
Blink: Indicates the switch is actively
sending or receiving data over that port.
Speed
Off
Indicates the link through established at
100Mbps
Green
Indicates the link through established at
1000Mbps
5. Switch Rear Panel
Figure 2 shows the rear panel of EPS-2010G
Figure 2. EPS-2010G Rear Panel
6. Network Installation
Please follow the steps described below to complete the network
installation.

Connect one end of a standard network cable to port-9.

Connect the other end of a standard network cable to the
network devices such as routers or workstations.

Install SFP transceiver and connect one end of a fiber cable to
port-9.

Connect the other end of fiber cable to the remote fiber device
-
8 x 10/100Base-TX port with 802.3af/at PoE Injector Mode
-
1 x 10/100/1000Base-T port
-
1 x 100/1000Base-X SFP slot
-
DIP switch for Default, VLAN and CCTV mode
-
4K MAC address table
-
Support 9K Jumbo Frames
-
Supports PoE power up to 30 watts for each PoE port
-
Total 120 watts PoE budget
-
Supports +/- 4KV surge immunity


Connect one end of a standard network cable to port-1 to
port-8 on the front of the PoE switch

Connect the other end of standard network cable to the
802.3af/at powered devices.

Connect one end of the power cable to the rear of the PoE
switch.

Connect the power plug of the power cable to a standard wall
outlet. When the PoE switch receives power, the Power LED
should remain solid Green.
7. DIP Switch
The front panel of EPS-2010G has one DIP switch that supports
“Default”, “VLAN” and “CCTV” modes. The detailed description are
shown in the following.
Note: After change the mode, in order to the corresponding
configuration take effect. The switch needs to restart manually.
Default DIP Switch Mode
The default DIP switch mode is general switch mode that can
normal communication between port 1~10.
VLAN DIP Switch Mode
The VLAN DIP switch mode is VLAN isolation mode that 1-8 port
can be isolated each other but 1-8 port can connect to 9~10 port.
CCTV DIP Switch Mode
The CCTV ON DIP switch mode is extension mode that allows 1-8
port to extend your network distance up to 250 meters at 10Mbps
while remaining to support 30W PoE power output.
8. Technical Specifications
Standards
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX/FX
IEEE 802.3ab 1000Base-T
IEEE 802.3z 1000Base-X
IEEE 802.3x Flow Control,
IEEE 802.3af Power over Ethernet,
IEEE 802.3at Power over Ethernet Plus
Interface
8-Port RJ-45 for 10/100Base-TX, auto MDI/MDIX
1-Port RJ-45 for 10/100/1000Base-T, auto
MDI/MDIX
1-Port SFP slot for 100/1000Base-X
PoE Injector Port
8-Port 802.3af/at PoE Injector (Port-1 to Port-8)
PoE Power Output
Max. 30W per port
PoE Budget
120W
Jumbo Frame
9K
MAC Address Table
4K
LED
Power, Link/ACT, PoE, Speed
Power
AC Input Voltage: 100V-240V 50/60Hz
Shipping Weight
1.3kg
Dimensions
220(W) x 150(D) x 44(H)mm
Temperature
Operating: 0oC~50oC; Storage: -20oC~60oC
Humidity
5%~90% RH non-condensing
EMC Safety
FCC Part 15 Class A, CE
Media
TP:
Fiber
EIA/TIA-568 CAT 3/4/5/5e
50/125, 62.5/125µm multi-mode fiber
9/125, 10/125µm single-mode fiber
*Please contact us for further reports and updates.
NOTE: Specifications may change without prior notice.
Contact Information
Connection Technology Systems INC (CTS)
18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: [phone] FAX: [phone]
E-Mail: [email protected]
EPS-2010G
8-Port 10/100Base-TX
802.3at PoE+
With 1-Port
10/100/1000Base-T + 1-Port
100/1000Base-X Switch
User’s Guide
Version 1.0