Conspit GT-lite User manual

CONSPIT GT-lite
Quick Guide
Elite Sim-racing Development

-1-
Product Disclaimer
We hereby reminds you that：
If you have any questions about this Disclaimer or the following product safety tips and operating
specifications, you can consult through [e-mail]. In the process of reading this
Disclaimer and the following product safety tips and operating specifications, you should immediately
stop using this product if you do not agree with any of the contents. If you do use this product,
your behavior will be regarded as an acceptance of this Disclaimer and the following product
safety tips and operation specifications.
Before using this product, please ensure that you have carefully read and fully understood this
Product Disclaimer and all the following product safety tips and operation specifications. To the
extent permitted by the laws of the People's Republic of China,
Ensu (Shanghai) Electronic Technology Co., Ltd. is not responsible for all personal injury and/or
property damage caused by your failure to obey any of the following safety tips or operating
specifications.
Safety messages during handling and installation:
- The product and its components are relatively heavy in weight. Please ensure that you or the installer
and user have sufficient lifting capacity. When handling and installing parts, please do so within your
capabilities. We recommend that at least two people work together to handle and install the product.
- The product is made of metal and has certain sharp edges. There is a possibility of collision injuries
during the handling and installation of parts. Please do not wear slippers, shorts, or clothing that
exposes a lot of skin during installation and use.
- When picking up and moving items, please make sure you have a firm grip. Dropping components
can cause property damage or even personal injury.
It is essential to use this product under safe conditions:
- Please ensure that the user has the ability to move independently and is conscious. Do not use
this product when sick, fatigued, or under the influence of alcohol/drugs.
Ensure proper installation of the product:
- This product requires you to complete some installation work. Make sure that all parts of
the bracket are properly and securely installed. Please follow the steps and instructions
in the product manual during the installation process. Using the product without proper
installation may result in the following: partial fasteners coming loose and causing collision
injuries, parts detaching and causing injury to yourself or others.
Safety information for product placement:
- Do not pile up debris within a 50-centimeter radius around the product. Leave enough
space around the product for comfortable use and movement.

-2-
Safety information during play:
- Do not carry sharp objects (such as keys, screwdrivers, utility knives, etc.) during activities.
Otherwise, serious personal injuries may occur.
- Avoid others entering the user's operating area.
- Avoid using excessive force. This product has been designed and manufactured with large
structural strength and safety margins to prevent component detachment/failure. However,
improper application of force beyond normal usage may still cause component damage,
leading to potential safety risks.
Situations that may pose hazards during normal use include, but are not limited to:
- Other people or pets coming close to the user's operating area.
- Electrical cables near the working area of pedals, steering wheels, and other moving parts.
- User's foot slipping off the pedal when applying force.
- Exposed skin on knees, arms, feet, legs, and other body parts due to inadequate clothing coverage.
Follow all safety tips and operating procedures:
- Avoid using the product for an extended period - prolonged continuous use may cause fatigue,
muscle pain, or other negative effects. We recommend a maximum single-use time of 2 hours,
and the daily maximum recommended usage time should not exceed 6 hours.
- Prohibit independent use by children under 12 years old, this product is not designed for use
by children. Children should use this product under the supervision of their guardian.
Malfunctioning and damaged products:
- If the product is damaged or cannot be used properly, please stop using it immediately and consult
CONSPIT's after-sales customer service. Continuing to use it may cause further damage to the product.
- Do not attempt to repair the product or its accessories by yourself.
General preventive measures:
- Please store and protect the product and its accessories properly.
- Do not immerse the product in liquid.
- Do not use the product in any environment with flammable substances.
- Using the product in dusty or dirty locations may cause damage.
- Do not drop the product (or its components) or subject it to physical impact.

-3-
CONSPIT GT-style series is specifically designed for GT racing and sports-car
seating posture. With a well-developed ergonomic system, it offers powerful
adjustability to meet the personal preferences of each driver.
GT-lite is designed with an Easy-Assembly Structure. Please verify all the
components listed in the packing list before starting the installation.
Follow the instructions in the manual to complete the installation
and fine tune your driving position.
The installation process is expected to take 20-40 minutes.

M6*12mm
Round head hex bolts
(26 pieces)
M8*100mm
Semi-tooth bolts (5 pieces)
13mm
open-end wrench
（1 pieces）
M8*16mm
Hex bolts (18pieces)
M8 flange nuts
(26 pieces)
M8 nylon anti-loose nuts
(6 pieces)
M8 Spacer
（5 pieces）
Hex wrench 6.0
Hex wrench 5.0
Hex wrench 4.0
Hex wrench 2.5
Hex wrench 2.0
M8*16mm
round head hex bolts
(5 pieces)
Packing list
-4-
*Safety Warning: Contains metal parts with sharp edges,
stay safe when installing.
Gloves Carpet（1 carpet ）

Packing list
-5-
*Safety Warning: Contains metal parts with sharp edges,
stay safe when installing.
C×2
EL
ER
E×2
FLFR
F×2
H×1G×1
I×1
A×2
AL
AR
B×2
D×1
CR
CL

-6-
Packing list (pre-assembled version)
M8*16mm
Hex bolts (18pieces)
M8*16mm
round head hex bolts (5 pieces)
M6*12mm
Round head hex bolts
（6 pieces）
M8 flange nuts
(22 pieces) M8 Spacer （5 pieces）
pre-assembled rig body
* Skip to page 13 if your GT-lite is pre-assembled version.
13mm
open-end wrench
（1 pieces）
Hex wrench 6.0
Hex wrench 5.0
Hex wrench 4.0
Hex wrench 2.5
Hex wrench 2.0
Gloves
Carpet（1 carpet ）

-7-
Installation of seat base
01
M6*12mm
Round head hex bolts (12 pieces) M8*16mm Hex bolts （4 pieces）M8 flange nuts（4 pieces）
Parts required for this step:
A×2
AL
AR
B×2 C×2 D×1
CR
CL

-8-
M6*12mm Round head hex bolts （8 pieces）
M8*16mm Hex bolts （4 pieces） M8 flange nuts（4 pieces）
The position shown in the picture is the recommended
seating position. However, you can adjust the rear
mounting position of the L-shaped plate to your
preference to change the angle of the seat.
* Do not tighten the bolts in this step for the convenience of
subsequent installation steps.
1
2

-9-
3
M6*12mm Round head hex bolts（（4 pieces））
*Tighten all the fasteners in the previous steps before
continue installing.

-10-
Installation of the wheelbase supporting pillars
02
M8*100mm
Semi-tooth bolts (4 pieces)
M8*16mm
Hex bolts (2 pieces)
M8 nylon anti-loose nuts
(6 pieces)
Parts required for this step:
E L
F L
F R
E R
E×2 F×2

-11-
* During installation, please ensure that the heights of the pillars
on both sides are the same.
M8 nylon anti-loose nuts
(6 pieces)
M8*100mm
Semi-tooth bolts (4 pieces)
M8*16mm Hex bolts
(2 pieces)
We recommend using this hole position as initial set-up,
but if you prefer a different wheelbase height,
you can adjust the fixing hole position
on the pillar to your desired setting.
Front view

-12-
Installation of pedal mounting plate
03
M8*16mm hex bolts (4 pieces) M8 flange nuts (4 pieces)
Because the angle of the pedal surface of different brands of pedals may
differ, we suggest that you install your pedals on the pedal base before
tightening the bolts shown in the figure below to facilitate the adjustment
of the driving position.
G×1
M8*16mm Hex bolts
(4 pieces)
M8 flange nuts
(4 pieces)
Parts required for this step:
* Mounting direction

Installation of wheelbase mounting plate
04
-13-
Parts required for this step:
H×1
I×1
M6*12mm
Round head hex bolts (8 pieces)
M8*16mm
Hex bolts (4 pieces)
M8 flange nuts
(4 pieces)

-14-
Supported devices:
Fanatec: Clubsport V1, Clubsport V2,Clubsport V2.5, CSL, CSL ELITE,
DD1, DD2
Thrustmaster: T300, T500 RS, TS-PC Racer, TX-XW Racer,
TMX Force Feedback, T-GT
SIMAGIC: M10, ALPHA, ALPHA MINI
Logitech: Driving Force GT, G920, G25, G27, G29, G923
Moza: All series
Simucube: Requires special mounting bracket
1
Please install bolts of the corresponding specifications according
to the instructions provided by your base manufacturer.
(GT-lite provides M6*12mm round head hex bolts)

2
3
-15-
M6*12mm
Round head hex bolts (4 pieces)
M8*16mm
hex bolts (4 pieces)
M8 flange nuts
(4 pieces)

-16-
Pitch angle adjustment
Front/rear adjustment
Seat Angle Adjustment
Steering Wheel Position Adjustment
* The middle mounting hole is
recommended to be the first option

-17-
Height adjustment

-18-
Pitch angle adjustment
A. The flatter angle of the pedal （-12°— 5°） base is suitable for pedals with
a more vertical pedal surface (such as CONSPIT CGP&CPP).
B. The steeper angle of the pedal （10°— 45°） base is suitable for pedals
with a certain degree of tilt.
Front/rear adjustment
Pedal Pitch Angle Adjustment

-19-
M3*8mm bolt (2 pieces) USB cable DC 12V power block
Installation of M-DVF kit
05
Knob
Motor
VIB controller
*Optional for M-DVF kit users