Contour Design RollerMouse mobile User manual

www.contourdesign.com
RollerMouse mobile

1
Quick Start
1. To connect via Bluetooth:
Power on RollerMouse Mobile (button A, see pg. 4). On your
computer, navigate to the area of settings regarding Bluetooth
connections (varies depending on operating system). Select the
option to add or discover a Bluetooth device. Your RollerMouse
Mobile should automatically be recognized, select it for the
computer to start Bluetooth connection.

2
Quick Start Cont’d
2. To connect via USB dongle:
Insert USB dongle into available USB port and power on your
RollerMouse Mobile. Your computer will recognize your new
device and connect automatically.
3. To connect via a wired USB connection:
Connect USB cable to your RollerMouse Mobile and into
an available USB port on your computer. Power on your
RollerMouse Mobile. Your computer will recognize your new
device and connect automatically.

3
What’s in the Box?
1. RollerMouse Mobile
2. Travel wrap (for RollerMouse Mobile)
3. Rubber feet (to raise keyboard height)
4. Dongle*
5. USB extender*
6. USB charging cable*
*Pleasendaccessories4,5,6
attached together in the box.
Functions
*The cursor speed button is multifunctional: On its own,
it controls cursor speed. Used in a sequence with other
buttons, it adjusts device settings. Please read on to learn
more about the functionality of this button.
• The LED indicators have corresponding tones to indicate a settings status.
An ascending tone indicates successful activation of a setting. A descending
tone indicates a setting was not successfully activated.
A. On/Off switch
B. Cursor speed/Settings*
C. Left-click
D. Right-click
E. Copy
F. Paste
G. Scroll wheel
H. Rollerbar

4
Top side
Left side Right side

5
Battery
• Battery level is shown when the device is powered on or plugged in.
• If battery is below 20%, a single light will blink to indicate the need to charge the device.
20% 40% 60% 80% 100%
Cursor Speed (DPI)
600 900 1200 1500 3000

6
Charging / Extension
To charge your RollerMouse remove the USB
extender and dongle from the charging cable.
Plug the USB-C end into the RollerMouse. Your
RollerMousewillchargein4hours.Youmay
continue to use your RollerMouse as it charges.
We recommend charging your RollerMouse once a
monthbasedonaveragedailyofceuse.See g. 1.
Wireless Connection
Once powered on, the device is in automatic mode
whichwillpairtotherstavailableconnection.The
devicewillattempttoconnecttothedonglerst.If
no connection is made, the device will attempt to
connect via Bluetooth using the pairing information
that is already in the unit. If no pairing information
is available, it will start Bluetooth pairing mode and
remain in that pairing mode for about two minutes. If
device is left in automatic pairing mode, RollerMouse
Mobile will cycle through the above steps each time
it’s powered off then powered back on again.
g. 1

7
1. Restart Bluetooth pairing:
Press button B. While continuing to hold B,
press and release button Ctwo times, then
release button B.
2. Select Bluetooth-only connectivity:
Press button B. While continuing to hold B,
press and release button Cthree times, then
release button B.
3. Select dongle-only connectivity:
Press button B, while continuing to hold B,
press and release button Dthree times, then
release button B.
Pairing and Secondary Options
• When the device is plugged in through the USB cable, this connection overrides wireless connectivity.
• Please visit contourdesign.com/BT for further information regarding your Bluetooth connection.
• If Bluetooth- or dongle-only connectivity is activated, the RollerMouse Mobile will retain
connection when the device is powered off then powered back on again.
4. Restore pairing with dongle:
Unplug then re-plug the dongle to the unit
to enable pairing. Hold the device close
to dongle and press button B. While
continuing to hold B, press and release
button Dtwo times, then release button B.
5. Reset wireless function to
automatic pairing mode:
Press button B. While continuing
to hold B, Press and release button
C, then release button B.

8

9
Click force refers to the level of resistance when clicking the Rollerbar. To adjust
click force, press and hold button Bthen press and release button H. Move button
Gup and down to adjust the click force settings. The current click force level will be
displayed by the LEDs on the right side of the unit. To disable the Rollerbar click,
adjust the click tension until all LEDs are illuminated.
Rollerbar Click Function (see gures 1&2)
g. 1