Contour RollerMouse Pro Wireless User manual
Wireless
Product
Manual
RollerMouse Pro
– 2 –
2
1. RollerMouse Pro
2. Wrist rest
3. Keyboard Risers
4. Dongle
5. USB extender
6. USB charging cable
What’s in the Box? User guide
3
1
5
46
– 3 –
A. Cursor speed
B. Power switch
C. Rollerbar
D. Copy
E. Paste
F. Left-click
G. Right-click
H. Scroll wheel
I. Double-click
Functions
A
B
C
DE
FG
H
I
H
A
B
– 4 –
Quick Start
1. Connect via Bluetooth
Power on RollerMouse Pro (button B). On
your computer, navigate to the area of
settings regarding Bluetooth connections.
Select the option to add or discover a
Bluetooth device. Your RollerMouse Pro will
automatically be recognized, select it for
the computer to start Bluetooth connection.
2. Connect via USB dongle
Insert USB dongle into available USB port
and power on your RollerMouse Pro. Your
computer will recognize your new device
and connect automatically.
3. Connect via a wired USB connection
Connect the USB cable to your RollerMouse
and into an available USB port on your
computer. Your computer will recognize
your new device and connect automatically.
– 5 –
Cursor Speed (DPI)
Press the Cursor speed (button A) to cycle through cursor
speeds. There are speed selections which range from slow
(600 DPI) to fast (2800 DPI). Speed can be identified by the LED
lights as shown. Hold Cursor speed (button A) for 8 seconds to
default settings.
Battery level
Battery level is shown when the RollerMouse Pro is powered on
or plugged in.
If battery level is below 20%, a single light will flash to indicate
the need to charge the device.
A
600 800 1000 1200 1400
1600 1800 2000 2400 2800
20 % 40 % 60 % 80 % 100 %
– 6 –
Rollerbar click force adjustment
Click force refers to the level of resistance when clicking the
Rollerbar. To adjust click force, press and hold button A (Cursor
speed) then press and release button C (Rollerbar). Move
button H (Scroll wheel) up and down to adjust the click force
settings.
To disable the Rollerbar click function, adjust the click tension
until all LEDs are illuminated.
Rollerbar click volume adjustment
The Rollerbar has 6 different click volume settings. To change
the click volume, press and hold button A (Cursor speed), while
continuing to hold A (Cursor speed), press and release button
H (Scroll wheel), the LED light will show current click vilume
setting. Move button H (Scroll wheel) up/down to adjust volume
setting. Release button A to confirm adjusted click volume.
To disable the Rollerbar click volume, adjust the click volume
until alle LEDs are illuminated.
– 7 –
Charging
To charge your RollerMouse remove the USB extender and
dongle from the charging cable. Plug the USB-C end into the
RollerMouse and connect to a USB-A at your computer.
Your RollerMouse will be fully charged in approx. 5 hours.
You may continue to use the RollerMouse as it charges.
Wiresless connection
Once powered on, the device is in automatic mode which
will pair to the first available connection. The device will
attempt to connect to the dongle first. If no connection is
made, the device will attempt to connect via Bluetooth
using the pairing information that is already in the unit. If no
pairing information is available, it will start Bluetooth pairing
mode and remain in that pairing mode for about two
minutes.
If the device is left in automatic pairing mode, the RollerMouse
will cycle through the above steps each time it's powered
off and then powered back on again.
–8 –
1. Restart Bluetooth pairing:
Press button A. While continuing to hold A, press and release
button F two times, then release button A.
2. Select Bluetooth-only connectivity:
Press button A. While continuing to hold A, press and release
button F three times, then release button A.
3. Select dongle-only connectivity:
Press button A, while continuing to hold A, press and release
button G three times, then release button A.
Pairing and secondary options
4. Restore pairing with dongle:
Unplug then re-plug the dongle to the unit to enable pairing.
Hold the device close to dongle and press button A. While
continuing to hold A, press and release button G two times,
then release button A.
5. Reset wireless function to automatic pairing mode:
Press button A. While continuing to hold A, press and release
button F, then release button A.
When the device is plugged with the USB cable, this connection overrides wireless
connectivity.
Please visit contourdesign.com/BT for further information about Bluetooth.
C
DE
FG
I
HH
A
B
– 9 –
Keyboard risers
Before using your RollerMouse Pro, please
take a moment to adjust your keyboard.
If you are using other keyboards than
Contour's Balance Keyboard, you can use
the Keyboard risers to achieve the desired
keyboard height and angle. Simply place
the Keyboard risers under your keyboards
feet - as the keyboard was lying on the
table.
For a proper ergonomic position the front
edge of the the keyboard should be as
close to the Rollerbar as possible. We
recommend to use negative tilt helping
you to hold a neutral wrist position and
decreasing the extension of your fingers.
Negative tilt
Neutral flat
Neutral elevated
Postive tilt
–11 –
Battery disposal
Contour Design Nordic A/S
Nyropsgade 41-43, 1. floor
DK-1602 Copenhagen V, Denmark
Phone: +45 70 27 02 27
Email: [email protected]
Contour Design, Inc.
10 Industrial Drive
Windham, New Hampshire 03087, USA
Phone: (603) 893-4556
Email: [email protected]
For more information please visit:
www.contourdesign.com
Tested to comply with FCC and
IC standards.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
IC Statement
This device complies with Industry Canada’s licence-
exempt RSSs. Operation is subject to the following two
conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
The term “IC:“ before the certification/registration
number only signifies that the Industry Canada
technical specifications were met. This product meets
the applicable Industry Canada technical
specifications.
Warranty
If there is a functional defect due to faulty
manufacturing, we will replace the product. This
warranty does not cover damage that results from
misuse of the product.
Attention!
If you attempt to dismantle your “RollerMouse Pro” you
will invalidate your warranty.
FCC Statement
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV
technician for help.
Table of contents
Other Contour Computer Accessories manuals
