Contour unimouse User manual

Wireless
Product Manual

Unimouse Wireless Unimouse Wireless
1
23
/1 /2
4
5
Unimouse FunctionsBox Contents
1. Unimouse
2. Dongle (Wireless receiver)
3. USB 2.0 cable adapter
4. USB to Micro USB cable/Charging cable
5. User Guide
For additional mouse features and specific Mac settings,
please download our driver at contourdesign.com/support
Auto scroll/Scroll wheel
Left click
Middle click/Double click*
Right click
Base/tilt
Charge port
Back button
Forward button
Thumb rest
Cursor speed adjustment (DPI)
Cursor speed/battery indicator
(LED)
* See page 4

Unimouse Wireless Unimouse Wireless
/3 /4
Power Switch Connecting to a Computer
The power switch can be found on the underside of the Unimouse. Before using
the Unimouse please make sure the power switch is set to the ON position.
Turning off the device is only necessary for long-term storage or during travel.
Plug the wireless receiver or the charging cable into the
computer’s USB port. Allow your computer a few seconds
to automatically install mouse drivers.
Charging Middle Click to Double Click
To charge your Unimouse remove the dongle from the extender cable
and plug the Micro USB into the Unimouse. Your Unimouse will charge
in 2 hours and you may continue to use your Unimouse while it charges.
Unimouse comes with middle click as the defualt setting. To change the middle
click function to double click, hold down the cursor speed button and the middle
click button at the same time. To switch back, repeat the same command.
Middle click / Double click
Cursor speed (DPI)

Unimouse Wireless Unimouse Wireless
e
/5 /6
Adjustable Features
The thumb rest can be extended
or collapsed to accomodate
different handsizes.
Slide the thumb support forward
or back to accomodate variations
in thumb length and grip
preference.
Adjust tilt for your desired
mousing angle.
The thumb support can be
rotated in any direction to adjust
to your prefered thumb position.
Unimouse has 4 key points of articulation. We econourage you to explore a
variety of positions while using your Unimouse. For more details regarding
adjustability, please refer to the Adjustability Guide.
With the Unimouse in close proximity to the dongle, hold left click, right click and
the cursor speed buttons at the same time until the LED indicator turns green
and pulses twice in succession.
Pairing
Cursor speed (DPI)
Left click
Right click

Unimouse Wireless Unimouse Wireless
100%
60%
20%
80%
40%
B
1) 800 2) 1000 3) 1200 4) 1400 5) 1600
6) 1800 7) 2000 8) 2200 9) 2400 10) 2800
/7 /8
Battery Level
Your Unimouse comes pre-charged and has an expected battery life of up to 3
months with average daily use.*
Unimouse has a built-in rechargeable battery. To see the battery level on your
device, press the cursor speed button once. The Unimouse will first display the
current cursor speed (DPI), then display the current battery level.
If your Unimouse is running low on battery, the center LED light will start
blinking in red.
To charge your battery, plug the charging cable into your Unimouse and connect
it to a USB port on your computer (see page 4). The Unimouse will charge in 2
hours and you may use your Unimouse as it charges.
*Battery life may vary based on user and computing conditions.
Change Cursor Speed
Press the cursor speed button to cycle through cursor speeds. There are
ten speed selections ranging from slow (800 DPI) to fast (2800 DPI). Speed is
indicated by the LED lights as shown.

FCC Statement
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: “ before the certication/registration number only signies that the Industry Canada technical specications were met. This
product meets the applicable Industry Canada technical specications.
Le présent appareil est conforme aux CNR d’Industrie Canada applicable aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement
For more information please visit:
www.contour-design.co.uk
Quay House
The Waterfront
Brierley Hill, Dudley
West Midlands, DY5 1XD
United Kingdom
Phone: [phone]
Email: [email protected]
Tested to comply with FCC
and IC standards
Warranty
If there is a functional defect due to faulty manufacturing, we will replace the product. This warranty does not cover
damage that results from misuse of the product.
Attention!
If you attempt to dismantle your Unimouse,, you will invalidate your warranty.