ConvaQuip 1731 Installation instructions manual

ConvaQuip Ind., Inc warrants the frame of product to be free
from defects in materials or workmanship for a period of lifetime
from date of purchase. If, within the specified warranty period,
this product is proven to be defective, it will be repaired or
replaced at ConvaQuip Ind., Inc option. This warranty does not
cover shipping costs incurred in replacement or repair of this
product.
ConvaQuip stands firm on our commitment to providing the
highest quality products, as well as exceptional service. This
product was built to precise standards and thoroughly
inspected prior to shipment. This Lifetime Limited Warranty
represents our confidence in the materials and workmanship of
our products. For warranty service, please contact the dealer
from whom you purchased your ConvaQuip product. In the
event that you do not receive satisfactory service, please call
us directly at the number below. Be prepared to indicate the
nature of the defect, the product serial number, and the name
and location of your dealer. You will also be required to provide
a receipt of your purchase. DO NOT return any products to our
office without prior consent. This warranty does not cover
problems due to user negligence or misuse of the product. This
warranty shall not extend to non-durable components,
including, but not limited to rubber tips, hand grips, casters,
brakes, and other parts subject to normal “wear and tear”.
These items are covered for a period of 90 days.
THIS FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU
OF ALL OTHER EXPRESS WARRANTIES, IMPLIED
WARRANTIES, IF ANY, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. CONVAQUIP SHALL NOT BE
LIABLE FOR ANY SEQUENTIAL OR INCIDENTAL DAMAGES
WHATSOEVER.
MANUFACTURED IN CHINA FOR:
ConvaQuip Ind., Inc
P.O. Box 3417
Abilene, TX 79604
Height Adjustable
Tool-Free Assembly
Holds up to 500 lbs.
INSTRUCTIONS
& WARRANTY
Bariatric Tub
Transfer Bench
Lifetime Limited
Warranty

* Make certain that the height adjustment snap buttons
fully protrude through the same respective holes of
each leg extension. This will ensure that the leg
extensions are securely locked in position ans an
even height is achieved.
* Ensure ALL screws, nuts and/or bolts are tightened.
* Check all the rubber tips on the leg extensions for
rips, wear or if they are missing. Immediately replace
any or all if any of these imperfections exist.
* All floor leg extensions with rubber tips MUST touch
the floor simultaneously at all times.
* DO NOT stand on transfer bench.
* ConvaQuip Ind., Inc. assumes no responsibly for
any damage or injury caused by improper install-
atio, assembly or use of this product.
Tip
Support
Arm
Suction
Cup
SAFETY GUIDELINES
PLEASE READ BEFORE USE
CAUTION: Transfer benches should be adjusted to
a height above the wall.
CAUTION: When removing a transfer bench from the
tub, always release the suction cups by
pinching the two tabs together.
INSTRUCTIONS FOR USE
Platform
Height
Adjustment
Back Support
Weight Capacity : 500 lbs.
Note: seat color may vary.
SET-UP:
1. Remove frame, back, support arm and legs from box.
2. Insert support arm into frame until support arm buttons
protrude fully through guide holes.
3. Place frame on side on a working surface.
4. Locate channel guides (4 each) on underside of seat.
Align seat support tubes with channel guides.
5. Slide seat support tubes through channel guides until seat
support tube buttons protrude fully through channel guide
holes.
6. Attach suction cup legs to frame on same side as support
arm. Attach flange tips to frame legs on opposite sides of
frame. from supoort arm.
7. Adjust seat height as directed in height adjustment section.
Assembly Instructions
HEIGHT ADJUSTMENT:
1. Depress the height adjustment button and slide the lower
leg upward or downward until the height adjustment button
is fully engaged in the desired hole.
2. Repeat for the other legs.
NOTE: Legs inside the tub may be adjusted to a different
height than the legs outside the tub. However, the
legs inside the tub should be adjusted to the same
height, and the legs outside of the tub should be
adjusted to the same height.
MAINTENANCE:
1. Use a soap and water solution, rinse with clean water,
then dry with a soft cloth.
2. Never use organic solvents, abrasive cleaners or
scouring pad on any part of the tub transfer bench.
3. Check fit and tightness of all nuts, bolts and knobs on
a weeklt basis to ensure tub transfer bench is safe to use.
Safety Precautions
DO NOT ATTEMPT TO ADJUST OR OPERATE
TRANSFER BENCH WITHOUT READING ALL
INSTRUCTIONS CAREFULLY.
Model 1731