Snug Seat Minnow User manual

Minnow Bath Support
User’s Manual – September 2006
By
1

INTRODUCTION
Thank you for purchasing the Minnow Bath Support from Snug Seat. When used properly
the Minnow should provide years of convenient bathing assistance.
It is very important to read all instructions before using this product. Keep these instructions
for future reference, as they contain vital safety and use information.
WARNINGS
• To prevent burns, set your hot water heater to 120 degrees Fahrenheit or lower. Always
check the water temperature before placing your child in the tub. Swirl the tub water
around with your hand to eliminate any hot spots.
THIS PRODUCT IS NOT A SAFETY DEVICE!
• Children have DROWNED while using infant bathing devices. Since children can drown
in as little as 1 inch (2.5 cm) of water, ALWAYS bathe child using as little water as
necessary.
• ALWAYS keep child within adult’s reach.
• DO NOT allow other children to substitute for an adult.
• DO NOT carry child in this product.
• ALWAYS test water temperature before placing child in this product.
• DO NOT use this product if any parts are missing or broken.
2

PARTS INVENTORY
WARNING
Before each use please inspect this product for damaged hardware, loose parts, missing
pieces, or sharp edges. Do not use this product if any parts are missing or broken.
Item
Number Quantity Provided Description
1 1 Bath Support PVC Frame
2 2 ¼-20 x 2.25” SS Carriage Bolt
3 2 Four-Arm Knob, Blue
4 1 Bath Support Pad Wrap
5 1 Frame Hanger Plate
6 1 Back Support Assembly Complete
7 2 #8 x ½” SS Sheet Metal Screw
8 1 Bath Support Hanger Wall Plate Assembly
3

Bath Support Hanger
Assembly
The Minnow Bath Support comes with a hanger assembly for easy drying of the unit and
convenient storage when not in use. Before using the Minnow, you must assemble the
frame hanger plate (5) to the pre-drilled PVC frame (1) using the stainless steel screws (7).
This assembly requires the use of a Phillips head screwdriver.
Use of Hanger
The Minnow Bath Support hanger wall plate assembly is provided with two large suction
cups that adhere to many bathroom surfaces. Hanging the Minnow is a convenient way to
speed drying of the unit and to store it when not in use.
WARNING
Pooled water can cause slippery surface conditions and increase the chances of falling in the
bathroom. Never hang the Minnow in an area where water can accumulate and pool
beneath it.
4

Back Support Assembly
Adjustment
The Minnow Back Support assembly can be height adjusted for optimal fit. Simply loosen
the blue plastic knobs (3), adjust the back support as needed, and tighten the blue knobs.
Safety Trunk Strap
The Safety Trunk Strap is provided to secure the user’s trunk in the Minnow. The Safety
Trunk Strap uses a hook and loop fastener for quick and easy closing and a safety buckle for
added security.
WARNING - Always secure the safety buckle!
Adding An Additional Back Support
A second Back Support can be easily added to the Minnow to accommodate taller users.
Assembly - The Back Support is independently height adjustable and can be
attached to the Minnow in-line with the standard back support (upright seating), or
slightly behind the standard back (recline seating).
Upright Seating Recline Seating
5

6
Minnow Bath Support
Cleaning and Care
Removable mesh seat pad
Machine wash warm and tumble dry. Use non-chlorine bleach as needed. Bleach will yellow
the cloth and accelerate deterioration especially if soaked.
PVC Frame and trunk pad
Use a mild detergent.
Measurements
Single Back
Support Dual Back Supports
Seat width 14" 14"
Back Support, Inside Width* 12" 12"
Back Support, Height Range 7½" to 10½" 7½" to 13¾"
Frame Width 17" 17"
Frame Depth 27½" 27½"
Product Weight 4.5 lb 5.4 lb
*The back support is made of aluminum and can be mildly bent to adjust to different torso widths.