Converters.TV Converter User manual

HDMI & IP over single cat6
Extender - ID# 866
Operation Manual

Introduction
Are you searching for a device that can make your home or office
more efficient? Then the HDMI™ & IP over a Single AT5e/ AT6 cable
is for you. This cutting edge product is more powerful than previous
generations of AT5e/ AT6 Transmitters and Receivers, because with
one Ethernet cable you are able to control the device through the
built-in RS-232 / IR ports, send uncompressed audio/video and
provide power to the receiver.
Applications
●House hold en tertain men t s harin g an d co ntro l
●Le ct ure ro om d is pl ay an d co nt ro l
●Sh o w ro o m d is p la y an d con t r ol
●Me et in g ro om p re se n tat io n a nd c on tr ol
●la ss ro om d is play a nd co nt ro l
Features
●HDMI v1.4 (with Audio Return hannel ), HD P & DVI
ompliant
●Supports HD P repeater and E function
●Simultaneously uncompressed data sending over a single 100M/328ft
AT5e/ AT6
●Uncompressed video 1080p, 60Hz, 48bits, 3D and 4K x 2K
●Audio supports up to 7.1 H & TrueHD, DTSHD
●Ethernet speed up to 100Mbps
●Various controls over HDMI E , RS232 & IR
●5Play™ convergence: HDMI, Internet, Power & ontrol (IR & RS232)
●Easy Installation
System
Requirements
Input HDMI source equipment such as DVD/Blue-Ray player and output
display with HDMI input jack.
IP router system or internet hub system and P /NB devices.

Operation Controls
and Functions
Front Panel
1. Power LED: This red LED will illuminate when the power is connected with AC
wall outlet.
2. DC 5V: These slots are where you plug the 5V DC power supply into the unit
and connect the adaptor to an AC outlet.
3. IR 1/2 Blaster: These slots are to connect with the IR blaster cables included
in the pac age for IR signal transmitting.
4. IR 1/2 Extender These slots are to connect with the IR receiver cables
included in the pac age for IR signal receiving.
5. RS-232 In: This slot is to connect with PC/laptop with D-Sub 9 pin cable for
RS-232 control system.
. HDCP LED: This red LED will illuminate in when the input source signal contains
HDCP data.
7. Link LED: This yellow LED will illuminate when the both input and output signal
is connected.
8. Mode LED: This green LED will blin ing when the device is processing data.
9. RS-232 Out: This slot is to connect to the device that wishes to be controlled
with D-Sub 9 pin cable for RS-232 signal to be execute.
10. CAT5e/ Out/IN: These slots are to be connected with a single CAT5e/6
cable for data transmitting.
Rear Panel
1. HDMI Bypass: This slot is to connect with HDMI TV/monitor for instant
display HDMI input source signal. W hen the HDMI bypass is connected, all
signals will not transmit to the receiver side. Therefore, unplug this slot after
confirm image display.
2. HDMI In: This slot is to connect with HDMI source equipment such as DVD/ Blue-
Ray player.
3. HDMI Out: This slot is to connect with HDMI TV/monitor for display HDMI input
source signal.
4. LAN 1 /2/3: These slots are to connect with internet server hub or IP system
allowing internet protocol to be transmit and received from 100M away. Either
side can be a transmit or receive side and all three LAN are shareable
within the two device's connection.

D-Su 9 Pin Definitions
Pin Define
1 N/C
2 TxD
3 RxD
4 N/C
5 GND
6 N/C
7 N/C
8 N/C
9 N/C
Specifications
Transmitter
-Inputs 1 x HDMI, 1 x HDMI Bypass, 3 x Ethernet,
1 x I , 1 x S-232
-Output 1 x CAT5e/CAT6
Receiver
-Inputs 1 x CAT5e/CAT6
-Output 1 x HDMI , 3 x Ethernet, 1 x I , 1 x S-232
ESD Protection Human body model:
+/- 8kV (air gap discharge)
+/- 4kV (contact discharge)
Operating Temperature Operating from 0°C – 40°C
Storage Temperature -20°C - 60°C
Relative Humidity 20 ~ 90% H non condensing

Connection and
Installation