Converters.TV 854 User manual

DVI over one CAT6 Extender
- ID# 854
Operation Manual

Introduction
The DVI-D Transmitter and Receiver over One CAT6 is an intelligent
device for extending your DVI-D signal over long distances to a
compati le display. Instead of searching for lengthy DVI ca les, your
existing CAT6 ca les can e utilized to perform advanced functions,
along with a andwidth up to 2.25G ps per channel. Also, the device
receives power through its USB connection, while Receiver is powered y
the CAT6 connection, which makes installing and powering the
Transmitter and Receiver more convenient. These devices are hardware
ased with fast and easy installation and are perfectly suited for
common PC and note ook using.
Features
• Supports digital video formats up to 36 its
• Support high definition input/output up to WUXGA/1080p
• Uses one CAT6 ca le for data/DDC transmission
• Equalizes and recovers incoming TMDS data efore re-transmitting it in
optimal quality
• DVI Ca le testing showed that with WUXGA/1080p 8 it resolution, input or
output device can run up to 12 meters away and with WUXGA/1080p12 it
resolution it can run up to 10 meters away
• When transmitting a signal in WUXGA/1080p 8 it resolution the CAT6
operating distance is 40 meters, and when the signal is in 12 it resolution the
CAT6 operating distance is 15 meters
• It is recommended to use power adaptor on oth transmitter and receiver
side to get the est performance and long distance operating.
• Using power adaptor on transmitter side only, receiver side powered over
CAT6 ca le, the operating CAT6 ca le distance will decrease to 20 meters
or less.
Applications
• DVI-D signal extension over CAT6
• DVI-D signal transmitting over long distance
System
Requirements
Input DVI-D signal source and output DVI-D input display with DVI connection
ca les and CAT6 ca le in etween the transmitter and receiver device.

Operation Controls
and Functions
Front Panel Transmitter Receiver
1. DVI-D IN: This slot is to connect with source equipment such as PC or
graphic card for input signal sending.
2. DVI-D OUT: This slot is to connect with display monitor or TV for image
display.
Rear Panel Transmitter Receiver
1. SDI IN: This slot is where you connect the SDI source to, in order to send
a SDI signal to a display.
2. SDI OUT: This slot is where you connect the SDI display to, with an SDI
ca le for displaying images. Connect it to another SDI to HDMI
converter/ extender to extend your signal or connect to multiple
displays.
. DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to an AC outlet. The red LED will turn on when the power is on.
Top Panel Transmitter Receiver
1. Power ED: The lue LED will illuminate when the device is connected with
power and detected the signal.

Specifications
Transmitter
Input 1 x USB (for Power), 1 x DVI-D
Output 1 x CAT6
Receiver
Input 1 x USB (for Power), 1 x CAT6
Output 1 x DVI-D
Input Ca le Distance 12M/ WUXGA or 1080p 8 it, 10M/ WUXGA or
1080p 12 it
Output Ca le Distance 12M/ WUXGA or 1080p 8 it, 10M/ WUXGA or
1080p 12 it
CAT6 Ca le Distance 40M/ WUXGA or 1080p 8 it, 15M/ WUXGA or
1080p 12 its
ESD Protection Human Body Model:
± 8kV (air-gap discharge)
: ± 4kV (contact discharge)
Operating Temperature 0ºC ~ 45ºC/ 32ºF ~104ºF
Storage Temperature -20ºC ~ 60ºC/ -4ºF ~140ºF
Relative Humidity 20~90% RH (non-condensing)
Power Consumption 3.5W/TX, 2W/RX

Connection