Cooper Lighting Solutions DLVP User manual

INS #
Brand Logo
reversed out of
black
INS #
Distributed Low Voltage Power System
Quick Start Guide DLVP
NOTICE: Designed for indoor installation and use only. Dry location rated.
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use outdoors (this item may be omitted if the product is suitable for outdoor use).
c) Do not let power supply cords touch hot surfaces.
d) Do not mount near gas or electric heaters.
e) Use caution when servicing batteries. Battery acid can cause burns to skin and eyes. If acid is spilled on skin or
in eyes, flush acid with fresh water and contact a physician immediately.
f) Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering
by unauthorized personnel.
g) The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
h) Caution: Halogen cycle lamp(s) are used in this equipment. To avoid shattering: Do not operate lamp in excess
of rated voltage, protect lamp against abrasion and scratches and against liquids when lamp is operating, dis-
pose of lamp with care.
i) Halogen cycle lamps operate at high temperatures. Do not store or place flammable materials near lamp.
j) Do not use this equipment for other than intended use.
SAVE THESE INSTRUCTIONS
WARNING
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this
product must be performed by a qualified electrician. This product must be installed in accordance
with the applicable installation code by a person familiar with the construction and operation of the
product and hazards involved. For continued protection against shock hazard replace all covers and
guards after field wiring is completed.
Risk of Fire and Electric Shock- Before installing or performing any service, the power MUST be
turned OFF. All installations should be in compliance with the National Electric Code and all state
and local codes.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care. Failure to comply with these instructions
may result in serious injury (including death) and property damage. Use caution when handling the
wallstation while the faceplate is removed.
DISCLAIMER OF LIABILITY: Cooper Lighting Solutions assumes no liability for damages or losses of any kind
that may arise from the improper, careless, or negligent installation, handling or use of this product.
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
NOTICE: Fixture may become damaged and/or unstable if not installed properly.
Note: Specifications and dimensions subject to change without notice.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on
delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be
filed within 15 days of delivery. All damaged material, complete with original packing must be retained.
All manuals and user guides at all-guides.com

DLVP - Distributed Low Voltage Power System
2
www.cooperlighting.com
1. MOUNT LOW-VOLTAGE POWER MODULE
Min. 3”
(75mm)
Min. 24”
(600mm) Min. 12”
(300mm)
2. PROVIDE POWER
All new wiring must be fully verified before applying power.
emergency power
connection
remove divider and wire internally
when NOT using EM panel
Note: LVPM-03-100-03 and LVPM-06-100-03 do not have emergency inputs
normal power
connection
Normal Power Input EM Power Input
120VAC 277VAC 120VAC 277VAC
LVPM-03-100-03-1E 1.76 0.76 0.88 0.38
LVPM-06-100-03-1E 4.40 1.90 0.88 0.38
3. CONFIGURE POWER MODULE
+ - + - + -
DEMAND CLOCK ALERT
LOW
HIGH
1 1 REC
BMS/OUT
2 2 SWITCH
PAC K
WALLSENSORS
12 3 4 5
V Y
ON
Occ / Vac Partial On
Y
N
Y
N
Select Occ Occ Share
F
S
Auto On
DEFAULT
10%
1
20%
30%
40%
2 3 4 5
DIAGNORM
DIP Switch Set A
Switch # / Mode Position Operation
1 / Occupancy VVacancy
OOccupancy
2 / Partial ON YPartial ON 50%
NScene 6
3 Selectable Occupancy YBy Zone
NBy Space
4 Occupancy Sharing YShare Sensor
NNo Sharing
5 Scheduled Level FFixed to Full / Off
DDefault Configured Scenes
4. CONNECT FIXTURES
STATUS
TEST
RESET
4 5 6
1 2
EMERGENCY
3
LOW-VOLTAGE OUTPUTS
SUITABLE FOR CLASS 2WIRING
LL503018EN
57VDC 90W MAX (EACH OUTPUT)
CAUTION: DO NOT OVERLOAD
+ - + - + -
DEMAND CLOCK ALERT
LOW HIGH
TRIM
1 1 REC
BMS/OUT
2 2 SWITCH
PAC K
WALLSENSORS
12345
V Y
ON
Occ / Vac PartialOn
Y
N
Y
N
Select Occ Occ Share
F
S
Auto On
DEFAULT
10%
1
20%
30%
40%
2 3 4 5
DIAGNORM
90W MAX
per LV output
circuit
Low-voltage
lighting cable
5. FIXTURE ZONE ASSIGNMENT
1 2 3 4 5 6
Zone 3
O
N
1 2 3 4 5 6
Zone 2
O
N
1 2 3 4 5 6
Zone 1
O
N
ote:N Zone 1 is any DIP switch configuration that is not specifically
zone 2 or zone 3.
ote:N During normal operation, avoid setting all DIP switches to the
ON position.
All manuals and user guides at all-guides.com

DLVP - Distributed Low Voltage Power System
3
www.cooperlighting.com
OR:
Z1
Z2
Z3
= zone 1
= zone 2
= zone 3
Open Loop Sensor
Sensor Range
2 Blinks = Low
3 Blinks = High
4 Blinks = Direct Sun
Direct SunHighLow
Daylight Gains
IntegratedSensor Settings
Motion
LVHH-01
TEST SET
+
+
LO
ID
5
10
15
20
Z
1
Z
2
Z
3
HI
+
321
−
+
−
+
−
DISABLE DISABLE
DaylightHoldTime
−
6. CONNECT WALLSTATIONS (up to 12)
STATUS
TEST
RESET
4 5 6
1 2
EMERGENCY
3
LOW-VOLTAGE OUTPUTS
SUITABLE FOR CLASS 2WIRING
LL503018EN
57VDC 90W MAX (EACH OUTPUT)
CAUTION: DO NOT OVERLOAD
+ - + - + -
DEMAND CLOCK ALERT
LOW HIGH
TRIM
1 1 REC
BMS/OUT
2 2 SWITCH
PAC K
WALLSENSORS
12 3 4 5
V Y
ON
Occ / Vac Partial On
Y
N
Y
N
Select Occ Occ Share
F
S
Auto On
DEFAULT
10%
1
20%
30%
40%
2 3 4 5
DIAGNORM
Pre-terminated
control cable
port
WALL
7. CONNECT SENSORS
(2 Occupancy / 1 Daylight)
Pre-terminated
control cable
Pre-terminated
control cable
GGRC-COUPLER
(Daylight Sensor Coupler)
OCC-RJ45
(Input/Output Device)
OCC-RJ45
(Input/Output Device)
GGRC-COUPLER
(Daylight Sensor Coupler)
STATUS
TEST
RESET
4 5 6
1 2
EMERGENCY
3
LOW-VOLTAGE OUTPUTS
SUITABLE FOR CLASS2 WIRING
LL503018EN
57VDC 90W MAX (EACH OUTPUT)
CAUTION: DO NOT OVERLOAD
+ - + - + -
DEMAND CLOCK ALERT
LOW HIGH
TRIM
1 1 REC
BMS/OUT
2 2 SWITCH
PAC K
WALLSENSORS
12 3 4 5
V Y
ON
Occ/ Vac PartialOn
Y
N
Y
N
SelectOcc OccShare
F
S
AutoOn
DEFAULT
10%
1
20%
30%
40%
2 3 4 5
DIAGNORM
STATUS
TEST
RESET
4 5 6
1 2
EMERGENCY
3
LOW-VOLTAGE OUTPUTS
SUITABLE FOR CLASS2 WIRING
LL503018EN
57VDC 90W MAX (EACH OUTPUT)
CAUTION: DO NOT OVERLOAD
+ - + - + -
DEMAND CLOCK ALERT
LOW HIGH
TRIM
1 1 REC
BMS/OUT
2 2 SWITCH
PAC K
WALLSENSORS
12 3 4 5
V Y
ON
Occ/ Vac PartialOn
Y
N
Y
N
SelectOcc OccShare
F
S
AutoOn
DEFAULT
10%
1
20%
30%
40%
2 3 4 5
DIAGNORM
Model:OCC-RJ45
OccupancySensor Coupler
Brown
Black
Red
Blue
Model:OCC-RJ45
OccupancySensor Coupler
Brown
Black
Red
Blue
STATUS
TEST
RESET
4 5 6
1 2
EMERGENCY
3
LOW-VOLTAGE OUTPUTS
SUITABLE FOR CLASS2 WIRING
LL503018EN
57VDC 90W MAX (EACH OUTPUT)
CAUTION: DO NOT OVERLOAD
+ - + - + -
DEMAND CLOCK ALERT
LOW HIGH
TRIM
1 1 REC
BMS/OUT
2 2 SWITCH
PAC K
WALLSENSORS
12 3 4 5
V Y
ON
Occ/ Vac PartialOn
Y
N
Y
N
SelectOcc OccShare
F
S
AutoOn
DEFAULT
10%
1
20%
30%
40%
2 3 4 5
DIAGNORM
STATUS
TEST
RESET
4 5 6
1 2
EMERGENCY
3
LOW-VOLTAGE OUTPUTS
SUITABLE FOR CLASS2 WIRING
LL503018EN
57VDC 90W MAX (EACH OUTPUT)
CAUTION: DO NOT OVERLOAD
+ - + - + -
DEMAND CLOCK ALERT
LOW HIGH
TRIM
1 1 REC
BMS/OUT
2 2 SWITCH
PAC K
WALLSENSORS
12 3 4 5
V Y
ON
Occ/ Vac PartialOn
Y
N
Y
N
SelectOcc OccShare
F
S
AutoOn
DEFAULT
10%
1
20%
30%
40%
2 3 4 5
DIAGNORM
Model:OCC-RJ45
OccupancySensor Coupler
Brown
Black
Red
Blue
Model:OCC-RJ45
OccupancySensor Coupler
Brown
Black
Red
Blue
OR:
port
SENSOR
8. CONNECT RECEPTACLE SWITCHPACK
(up to 5)
STATUS
TEST
RESET
4 5 6
1 2
EMERGENCY
3
LOW-VOLTAGE OUTPUTS
SUITABLE FOR CLASS 2WIRING
LL503018EN
57VDC 90W MAX (EACH OUTPUT)
CAUTION: DO NOT OVERLOAD
+ - + - + -
DEMAND CLOCK ALERT
LOW HIGH
TRIM
1 1 REC
BMS/OUT
2 2 SWITCH
PAC K
WALLSENSORS
12 3 45
V Y
ON
Occ / Vac Partial On
Y
N
Y
N
Select Occ Occ Share
F
S
Auto On
DEFAULT
10%
1
20%
30%
40%
2 3 4 5
DIAGNORM
Pre-terminated
control cable
port
REC
BMS/OUT
See full instruction manual: www.cooperlighting.com
Installation videos: YouTube.com
All manuals and user guides at all-guides.com

Cooper Lighting Solutions
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
© 2020 Cooper Lighting Solutions
All Rights Reserved
Publication No. IB503030EN
January 2020
Cooper Lighting Solutions is a
registered trademark. All
trademarks are property
of their respective owners.
Product availability, specifications,
and compliances are subject to
change without notice.
Warranties and Limitation of Liability
Please refer to www.cooperlighting.com for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site www.cooperlighting.com pour obtenir les conditions générales.
Garantías y Limitación de Responsabilidad
Visite www.cooperlighting.com para conocer nuestros términos y condiciones.
All manuals and user guides at all-guides.com