Cooper Lighting All Pro APX Exits User manual

WALL MOUNT INSTALLATION
Step 1. De-energize the circuit at the junction ox (J- ox) where the
exit sign is to e installed.
Step 2. Remove the exit sign stencil from the EXIT frame. Remove
and discard the plastic canopy from inside the EXIT.
Step 3. Knock out the appropriate mounting pattern and the wire
pass hole in the EXIT ackplate to fit the J- ox eing used.
Step 4. Feed the orange, lack, and white wires through the center
hole.
Step 5. Connect the J- ox wires to the EXIT power supply wires
using the wire nuts provided. Connect the white wire to
neutral. If using 120V, connect the lack wire to the hot lead.
If using 277V, connect the orange wire to the hot lead. Cap
the unused lead. Press the wires into the J- ox.
Step 6. Secure the EXIT to the ackplate using installer supplied
hardware.
Step 7. For self powered units, attach attery leads to PCB.
Step 8. Snap the EXIT stencil onto the frame.
Step 9. Energize AC supply, LED display will come on.
COOPER LIGHTING
Insta ation Instructions for the A Pro APX Exits
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS
BE OBSERVED INCLUDING THE FOLLOWING:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
2. Do not use outdoors.
3. Do not use in hazardous locations, or near gas or electric heaters.
4. Do not let power supply cords touch hot surfaces.
5. Use caution when servicing atteries. Battery acid can cause urns to skin and eyes. If acid is spilled
on skin or in eyes, flush acid with fresh water and contact a physician immediately.
6. Do not use this equipment for other than the intended use.
7. Installation is to e performed only y qualified personnel.
8. Install in accordance with National Electric Code and local regulatory agency requirements.
9. The use of accessory equipment not recommended y the manufacturer may cause an unsafe
condition.
10. Equipment should e mounted in locations and at heights where it will not readily e su jected to
tampering y unauthorized personnel.
11. SAVE THESE INSTRUCTIONS
HOLE PLUG -
REMOVE FOR
CEILING MOUNT
CANOPY
MOUNTING PLATE
MOUNTING PLATE
CANOPY
HOLE PLUG -
REMOVE FOR
WALL MOUNT
Risk of Electric Shock
Disconnect power at fuse
or circuit breaker before
installing or servicing.
Risk of Fire/Electric
Shock
If not qualified, consult an
electrician.
Customer First Center 1121 Highway 74 South Pea htree City, GA 30269 770.486.4800 FAX [phone] 049-205

COOPER LIGHTING
CEILING OR END MOUNT INSTALLATION
Step 1. De-energize the circuit at the junction ox (J- ox) where the exit sign is to e installed.
Step 2. Remove the exit sign stencil from the EXIT frame.
Step 3. Remove the canopy kit from inside the EXIT.
Step 4. Place the provided screws in the canopy screw holes. Ta s inside the holes will prevent the screws from falling out during installation.
Step 5. Remove the appropriate mounting hole plug on the top (ceiling mount) or side (end mount) of the frame.
Step 6. Place the canopy nose through the mounting hole until the side of the frame touches the canopy. Lock the frame onto the canopy y sliding the
frame in a direction parallel to the canopy length toward the narrow end of the mounting hole. Slide the frame until oth snaps engage the canopy
nose preventing any motion ack out of the hole.
Step 7. Feed the orange, lack, and white wires through the canopy nose.
Step 8. Feed the wires from the J- ox through the steel mounting plate, then attach the mounting plate to the J- ox with installer provided hardware.
Step 9. Connect the J- ox wires to the EXIT power supply wires using the wire nuts provided. Connect the white wire to neutral. If using 120V, connect
the lack wire to the hot lead. If using 277V, connect the orange wire to the hot lead. Cap the unused lead. Press the wires into the J- ox.
Step 10. Secure the EXIT canopy to the steel mounting plate using the screws placed in the canopy in step 4.
Step 11. For self powered units, attach attery leads to PCB.
Step 12. Snap the EXIT stencil onto the frame.
Step 13. Energize AC supply, LED display will come on.
SELF POWERED OPERATION: Depress the test switch. The LED display will remain lit and the charge LED will extinguish when the
switched to attery power. Release the test switch. The charge LED will illuminate and the LED display will operate from the AC supply.
MAINTENANCE: None required. For self powered units, replace the atteries as needed according to am ient conditions. However, we
recommend that the equipment e tested regularly in accordance with local codes.
NOTE: Servicing of any parts should e performed y qualified personnell. Only use replacement parts supplied y Cooper Lighting.
CAUTION: This equipment is furnished with a sophisticated low voltage attery dropout circuit to protect the attery from over discharge after its
useful output has een used. Allow 24 hours recharge time after installation or power failure for 90 minute testing.
TROUBLE SHOOTING GUIDE: If LED display or harge indi ator LED does not illuminate, he k the following:
1. Che k AC supply – verify that unit has 24 hour AC supply.
2. Unit is shorted or battery is not onne ted.
3. Battery dis harged. Permit unit to harge for 24 hours and then re-test.
4. If following the above trouble shooting hints does not solve your problem, onta t your lo al Cooper Lighting representative for
assistan e.
ORANGE LEAD - TO 277V
BLACK LEAD -TO 120V
WHITE LEAD - TO NEUTRAL
LED DISPLAY PC BOARD
POWER SUPPLY
PC BOARD
BATTERY
SCHEMATIC
Customer First Center 1121 Highway 74 South Pea htree City, GA 30269 770.486.4800 FAX [phone] 049-205