Coopers of Stortford 10708 User manual

Step1: Insert the battery into the transmitter to be used
(Doorbell button)
Step 2: Insert the batteries into the receiver (chime unit).
Step 3: Enter pairing mode for the receiver (chime unit).
Press and hold the ● zone selector button for 3
seconds. The LED in zone #1 will flash.
Step 4: Press the ● zone selector button again to move to the
zone you wish to pair with. Press ♫ button to scroll
through the melodies. Once you hear a melody you
prefer, do not press any button as the melody is set
for that zone.
Step 5: Once the zone & melody are selected, press the
Doorbell button once to pair. If successful, the
receiver (chime unit) will generate two short tones. Press the ● zone selector button to
exit the pairing mode, the system is now ready to use.
Wireless Receiver w/Doorbell 10708 Instrucons for Use
Please read and retain these instrucons for future reference v001: 23/11/16
Head Office, 11 Bridge Street
Bishop's Storord CM23 2JU
Tel: [phone]*
Fax: [phone]
www.coopersofstorord.co.uk OF STORTFORD
*Calls Cost 7 pence per minute plus your telephone company's network access charge
PARTS & FUNCTION DOOR BELL
PARTS & FUNCTION DOOR BELL
Battery compartment Access Door
Speaker
Zone ID
Flasher
Zone selector button
Melody
selector button
Reset button
DC jack
Mounting holes
Volume control
Receiver
Strobe/melody switch
MOUNTING
MOUNTING
Or
Hang on a wall Stand on firm flat surface
such as a desk or table
POWER
POWER
- +
Using an AC/DC
adaptor (not included)
Using C size
batteries (not included)
'C' Size
1.5V
'C' Size
1.5V
'C' Size
1.5V
Vibration pad ON/OFF switch
Vibration out
Indicators
12V DC 400 mA
Battery
compartment
or use sticker provided
+
CR2032 (included)
Open the cover
or
Doorbell pusher
Call button
Name plate
Zone select button
Melody selector button
Zone ID Chime Only
Chime/Strobe
Strobe Only
CODE PAIRING & MELODY SELECTION
* PLESE NOTE THE BELL PUSHER AND CHIME UNIT ARE PAIRED AND
READY TO USE.
To stop the Chime while the receiver (chime unit) is alerting press the reset button.

Press and hold the ● zone selector button for 3 seconds to enter the pairing mode. Press the ●
zone selector button to move to the zone you want to delete. Press and hold the ● zone selector
button and the ♫ button together for 3 seconds to delete the memory. The receiver will generate a
tone to indicate the transmitter on the specified zone has been deleted.
Press and hold the ● zone selector button for 3 seconds to enter the pairing mode. Press the ●
zone selector button to move to the zone then press the ♫ button to select the melody required.
Press the ● zone selector button until the pairing mode is exited.
Clear transmitter on the chime memory
Change the melody in desired zone
To cancel any alert on the remote receiver press the reset button. The reset button is located on
the back of the receiver behind the flasher.
Notes
Wireless Receiver w/Doorbell 10708 Instrucons for Use
Please read and retain these instrucons for future reference v001: 23/11/16
Battery low indicator
If a zone LED is blinking, it indicates that the battery is low for this transmitter. You must replace
the battery as soon as possible. If the white flash at the top of the chime blinks every 5 seconds,
this indicates the receiver batteries are low. You must replace the batteries of the receiver
immediately.
For best results, use good quality alkaline baeries.
Always replace old or weak baeries.
Keep doorbell dry. If wet, dry immediately.
Do not use cleaning solvents on electronic products.
Solvents contain chemicals that can damage circuitry. Use damp towel or cloth to clean. Dry immediately.
Do not expose the bell unit to rain or immerse in water. It is not water resistant.
Keep baeries away from children and pets.
Remove the baeries if le for long periods.
Never dispose of baeries in a fire.
Follow the baery manufacturer’s safety, usage, and disposal instrucons.
Dispose of all packaging, paper, cartons and plasc, plasc bags in accordance with your local recycling regulaons.
BATTERIES
Do not mix used and new baeries.
DISPOSAL
At the end of the product’s lifespan please dispose of it at an authorised household WEEE waste recycling centre.
WARNINGS / CAUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Baery disposal, spent or expired baeries must be properly disposed of and recycled in compliance with
local regulaons. For detailed informaon, contact your local authority.
Head Office, 11 Bridge Street
Bishop's Storord CM23 2JU
Tel: [phone]*
Fax: [phone]
www.coopersofstorord.co.uk OF STORTFORD
*Calls Cost 7 pence per minute plus your telephone company's network access charge